Booker water heater functions and instructions, Booker water heater use steps

What's going on with the Booker water heater not decelerating.

Precautions before using the electric water heater:

1. Before use, it must be filled with water before turning on the power to prevent the electric heating pipe from leaking due to dry boiling.

2. The reliable ground wire must be connected, if there is no good grounding device, it should be preheated and cut off the power supply before use. Due to the large power of the electric water heater, the cross-sectional area of the power cord should be greater than the square millimeter.

3 The socket must use a 10A 15A socket.

The contact between the plug and the socket must be firm and firm, and cannot be loosened;

And the fuse holder with appropriate current should be configured on the special line to prevent the line from being too thin and the contact is poor, resulting in leakage and fire.

The basic steps of using the electric water heater are to pass the water The first time you use the electric water heater, you should pay special attention to the hot water valve of the hot and cold water regulating valve first, and then open the tap water valve leading to the water heater, the water enters the water heater, and the air is discharged, and the water flow out of the shower or hot water faucet, indicating that the water heater is full of water, and then close the hot water faucet. Power on Check that the water supply system is normal and then turn on the power heating, you can set the required water temperature first, and then plug the power plug into the socket and turn on the power. Heating After the circuit is turned on, turn on the switch of the water heater, the red light indicates that everything is normal, and the heating starts;

The yellow light is on and the red light is off, indicating that the heating has stopped, and the water temperature has reached the requirements, and the water can be discharged.

Hot water discharge The temperature of the hot water that has just been released is high, so you should pay attention when using it. When adjusting the temperature of the shower water, the shower head should not be directly facing the human body, and test the water temperature with your hands first to avoid burns.

Maintenance and cleaning of electric water heatersRemember to maintain and clean the electric water heater frequently1.

1. First open the hot water valve or hot water faucet of the cold water regulator so that the air can be exhausted when the water is filled.

2. The water valve of the water heater, but do not open it too much to avoid impact.

3. When there is water flowing out of the hot water faucet or hot water nozzle, the straight valve for hot water outflow is closed.

4. Plug the power back into the socket and turn it on.

5. The heating lamp starts to work and starts heating.

6. The water heater is starting to work.

The key points of use of electric water heaters are four steps: "water on, electricity on, heating, and hot water discharge".

The following describes the operation process of a closed water heater.

Access to water. For the first use, pay special attention to opening the hot water valve or hot water faucet of the cold water regulating valve first, so that the air can be exhausted when filling water. Then open the tap water valve leading to the water heater and fill the water heater with water, so as not to open it too much to cause a large impact.

When water flows out of the hot water faucet or nozzle, it means that the water heater is filled with water, and turn off the hot water outlet valve.

Power. After checking that the water supply is normal, set the desired water temperature, then plug the power plug into the socket and turn on the power supply.

Heating. After the circuit is connected, turn on the power switch of the water heater, the heating light is on to indicate normal, and the heating starts. The heating lamp is off and the heat preservation lamp is on, indicating that the heating has stopped and the water temperature has reached the required level.

Hot water is put in. For suitable use, the mixing water temperature can be adjusted, i.e. the flow of hot and cold water can be adjusted. When adjusting the water temperature, test the temperature with your hands, and do not flush directly on your body to avoid burns.

Closed water heaters allow continuous work, can automatically control the temperature, and can be selected according to the needs of the home. If there is no special need, the temperature control is not easy to adjust too high to save energy and prolong the life of the water heater. The open water heater cannot be automatically filled with water, and must be manually filled to the required water level, but the water level must not exceed the electric heating pipe by more than 10cm, and generally at least half of the water must be used.

Before using the open water heater, be sure to cut off the power supply to ensure safety.

Booker's water heater display flashed, what's going on.

Hello, I am happy to serve you and give you the following answers: Booker water heater failure**Daquan:: This is a failure caused by the failure of the temperature sensor of the water heater**, which may be caused by the poor connection of the temperature sensor or the failure of the temperature sensor itself.

Solution: Check the connection of the temperature sensor, if the connection is normal, replace the temperature sensor. : This is a malfunction caused by a malfunctioning water level sensor in the water heater**, which may be caused by a poor connection to the water level sensor or a malfunction of the water level sensor itself.

Solution: Check the connection of the water level sensor, if the connection is normal, replace the water level sensor. : This is a malfunction due to a malfunction of the water heater's power supply**, which may be caused by a poor connection of the power supply or a malfunction of the power supply itself.

Solution: Check the connection of the power supply, and if the connection is normal, replace the power supply. : This is a malfunction caused by a faulty controller of the water heater**, which may be caused by a poor connection of the controller or a malfunction of the controller itself.

Solution: Check the connection of the controller, and if the connection is normal, replace the controller. Personal Tips:

1.When using a Booker water heater, the various parts of the water heater should be checked regularly to ensure that it is functioning properly. 2.

If the water heater is found to be faulty, it should be dealt with in time to avoid more serious damage. 3.If you are not familiar with water heaters.

Summary. When there is e6**, it not only means that the electric water heater should be burned dry, but also it means that there is a failure, e6 is also a fault**, when e6 appears, it may indicate that some of the original parts of the computer version may be burned out, then this time is not what we can solve, at this time we need to ask professional repairers to solve the electric water heater, in this part it is not recommended that we do it ourselves, because it is possible to accidentally touch other lines, Cause other unnecessary troubles.

Hello dear! Glad to answer this question for you, Booker water heater failure** Daquan.

e1 means that the ignition of the water heater is unsuccessful, that is, it does not ignite. There are many reasons why the gas water heater cannot catch fire, and the components of water, gas, and electricity are damaged, which will cause the water heater to fail to ignite. In fact, many times the reason why the fire cannot be ignited is because of the waterway scaling caused by the waterway scaling or the hot water pipeline blockage caused by the noise, resulting in a large waterway flow back pressure, which is large to a certain extent, and the water heater water-gas linkage device will think that the hot water faucet has been closed and the gas channel is closed, and there is no gas, of course, it cannot be ignited.

If the accompanying phenomenon is that the water heater faucet is significantly smaller than the cold water faucet, then it can basically be confirmed that the scale is to blame. The solution is regular descaling.

When there is e6**, not only does the brigade only mean that the electric water heater should be burned dry, but it also means that there is a fault, e6 is also a fault**, when e6 appears, it may indicate that part of the original part of the computer version may be burned out, then at this time it is not that we can solve the limb sebb settling, at this time we need to ask professional repair of electric water heaters to solve, in this part is not recommended for us to do it ourselves, Because it is possible to accidentally touch other threads, causing other unnecessary troubles.

Summary. The steps are as follows:1

Locate the water heater's inlet valve, usually located at the bottom or side of the front of the water heater, and rotate the inlet valve to the open state. 2.Turn on the cold water tap and let the tap water flow into the water heater until the inside of the water heater is filled with water, and no more air bubbles are emitted from the faucet, and water is flowing out.

3.Turn off the cold water tap and wait for the water heater to heat up, usually about 10-30 minutes, depending on the water heater model and temperature setting. 4.

Turn on the hot water faucet and check if the hot water flow and water temperature are normal, if it is normal, the water heater has been successfully filled.

The steps are as follows:1Locate the water heater's inlet valve, usually located at the bottom or side of the front of the water heater, and rotate the inlet valve to the open state.

2.Turn on the cold water tap and let the tap water flow into the water heater until the inside of the water heater is filled with water, and there are no more bubbles emitting from the faucet, and there is water flowing out and lumpy. 3.

Turn off the cold water tap and wait for the water heater to heat up, usually about 10-30 minutes, depending on the water heater model and temperature setting. 4.Turn on the hot water faucet and check if the hot water flow and water temperature are normal, if it is normal, the water heater has been successfully filled.

Notes:1During the water supply process, make sure that the switch of the source of the electric book is turned off to avoid accidental electric shock.

2.Keep the surroundings of the water heater clean and dry to ensure that the water heater is working properly. 3.

If you find that the water heater is leaking or has abnormal noise, you should stop using it immediately and contact the after-sales personnel for maintenance in time.

Summary. The method of water supply in Booker water heater is a storage electric water heater, when you use it for the first time, open the water inlet valve, and then open the valve that discharges hot water, and you can hear the sound of water inlet. When the shower has water and air discharged, until it is clean water without dirt and air, the water inside is full.

Don't close the inlet valve, let it stay open, and keep the water inside always full. As much hot water as you use, it will enter as much cold water, and the water in it will not be used up. If there is no cold water going in, hot water cannot be released.

The method of water supply in Booker water heater is a storage type bent electric water heater, when you use it for the first time, open the water inlet valve, and then open the valve to discharge hot water, you can hear the sound of water inlet. When the shower has rotten water and air discharged, until it is clean water without dirt and air, the water inside is full. Don't close the inlet valve, let it stay open, and keep the water inside always full.

As much hot water as you use, it will enter as much cold water, and the water in it will not be used up. If there is no cold water going in, hot water cannot be released.

1. Turn on the hot water faucet first, and the air must be discharged to facilitate the injection of water after the attack. 2. Open the tap water valve, and you can directly fill the water heater with water. 3. Turn on the water tap or faucet, if there is water flowing out, it means that the water heater is full.