The angle valve on the wall of the water heater is dripping, no matter how you get it, what should I

First observe whether the water inlet hose and the angle valve thread are in contact with the leakage, or the angle valve is leaking from the outlet pipe on the wall, or the angle valve body is leaking.

If there is a leak in the contact between the inlet hose and the angle valve thread, take out the inlet hose to see if there is a gasket in the nut, if there is, the nut is not tightened enough, and it can be tightened from scratch.

If the angle valve and the water outlet pipe on the wall are leaking, it may be that the raw material belt does not have the effect of sealing water, and you can re-circle the raw material belt and then install it.

If the angle valve body is leaking, then the angle valve can only be replaced.

First, to replace a new angle valve, it is best to purchase copper angle valve:

Except for the right-angle body, the structure of the angle control valve is similar to that of the straight-through single-seat control valve. It is suitable for applications with high viscosity, suspended solids and granular fluids, or where right-angle piping is required. The flow direction is usually bottom-in and side-out.

Under the condition, it can be reversed, that is, the flow goes to the side and the bottom exit. There are two kinds of hot and cold valves, and most of the raw materials are the same, which is symbolized by hot and cold, mainly to distinguish which is hot water and which is cold water.

Second, the accurate way to surround:

1. Remove foreign bodies from the joint parts and keep them clean;

2. Pay attention to the direction of surrounding, taking the angle valve as an example, the angle valve rotates clockwise to the right when the inner wire thread is screwed into the wall, so the direction of wrapping the leftover strip on the angle valve is counterclockwise to the left, so that the time of tightening the angle valve will be tighter and tighter, and it will not be loosened.

3. When winding, the raw material belt should be tightened, so that the raw material belt is tightly attached to the thread, as tight as possible, do not loosen the winding, and press it tightly with your hand after wrapping, and you can also wrap it while pressing.

4. There is no hard and fast rule as for the "several layers" around, which can be tightened and does not leak, but it usually needs to be wrapped more than a dozen times to ensure the sealing effect.

3. Matters needing attention to when installing angle valves:

1. Ask professionals to carry out the installation, and require the device to be in the outstanding local area of the water to avoid accidental loss.

2. Before the installation, please be sure to clean the sand and debris connected to the outlet pipe to prevent the formation of jamming on the ceramic chip and causing water leakage.

3. When installing, do not grasp the handwheel of the angle valve by hand and rotate and fasten, wrap several layers of cloth or paper towels and other buffers on the valve body, and then use a wrench to clamp the valve body and rotate it for fastening. If the valve body is clamped directly without a cushion, the appearance of the angle valve may be bruised, which will affect the appearance.

First observe whether the contact between the inlet hose and the thread of the angle valve is leaking, or the angle valve is leaking from the outlet pipe on the wall, or the angle valve body is leaking?

If there is a leak in the contact between the water inlet hose and the angle valve thread, then take out the water inlet hose to see if there is a gasket in the nut, if there is, the nut is not tightened enough, just tighten it from the beginning.

If the angle valve and the water outlet pipe on the wall are leaking, it may be that the raw material belt does not have the effect of sealing the water, and it is enough to re-circle the raw material belt and install it.

If the angle valve body is leaking, then the only way to replace the angle valve is to replace it!

Take a closer look at the copper head buried inside the wall, there may be cracks.

More savvy. Buy a triangle valve and a raw meal belt. The main valve is closed. The water runs out and you can do it yourself.

There are 3 tricks for the water heater to keep dripping water when the drain valve is dripping.

1. It may be because the water pressure of the tap water is too large, and it is inevitable that there will be water splashing in the process of water feeding, resulting in the water in the water tank flowing out of the exhaust hole when it is not full.

Solution: The water pressure of the tap water needs to be adjusted.

2. It may be because the water valve of the water heater is not closed tightly, resulting in water seeping.

Solution: It is necessary to tighten the water supply valve of Tongshu water heater.

3. It may be because the water temperature of the water heater is a little high, which causes the hot water to emit hot gas and condense into water droplets.

Solution: You need to adjust the water temperature of the water heater to the appropriate temperature.

What to do after a water leak is found:

Once you notice that the water heater is dripping, be sure to unplug the water heater and make sure to turn off the power before the water is detected.

The drain valve of the water heater has been dripping, it may be that there is a problem with the valve of the water heater, the boiling time is too long, resulting in too much pressure inside the inner tank of the water heater, and the valve door is not closed tightly enough, resulting in water dripping out, which is a normal situation, but it is still not recommended to boil water for a long time.

When there is a dripping situation in the drain valve, it may be caused by excessive pressure inside, you can turn off the power and then open the drain for cleaning. It is also possible that the drain valve of the water heater has been dripping due to loose screws, so you need to tighten the screws, and replace the new nuts in time if the screws appear. The recommended maintenance methods are:

1. For newly installed water heaters, be sure to fill the inner tank with water before plugging it in. 2. Regularly drain the water heater system, which can prevent the pipeline from being blocked, and clean the water tank to ensure the cleanliness of the water quality. 3. When the water heater is discharged, it is necessary to ensure that the water enters the water, and under normal circumstances, open the sewage valve to the sewage valve to flow out of the clean water.

4. In the long-term use of the water heater, the water contains trace impurities and mineral precipitation, such as irregular cleaning will affect the effluent quality and service life, the cleaning of the inner tank is recommended to be operated by professionals. 5. The water heater must be powered off when it is not used for a long time, which can prolong the service life of the water heater. 6. Check the valve of the water heater regularly to prevent the water heater from dripping.

Water heater leakage is a frequent failure in the use of water heaters, generally speaking, the common causes of gas water heater leakage are probably as follows: 1. Water heater water tank leakage, often occurs in winter, the temperature is too low and the water temperature freezes and cracks. Or the place directly opposite the open flame is easy to burn through, causing the water heater to leak.

2. The water-gas linkage valve of the gas water heater is leaking, and there is a water diaphragm used to push the gas valve in the valve, which is easy to age and leak after a long time. 3. There are three situations of water leakage at the water pipe of the gas water heater: First, the water heater interface is not installed firmly; Second, the water heater leakage caused by the rupture of the water heater pipe; The third is that the water heater valve is leaking.

If the water pressure of the tap water pipe is too large, when the pressure of the tap water suddenly increases or the heating is overheated and the pressure of the inner tank is too large, the safety valve will automatically drip and relieve the pressure, so as not to damage the inner tank due to excessive pressure. Therefore, during the heating process, the slow dripping of the safety valve is a normal positive sign, not a problem with the quality of the water heater.

It is recommended that the user close the inlet valve and adjust the knob of the mixing valve to the high temperature to open it to avoid the leakage of the one-way safety valve and make the water drip out of the shower; If the mixing valve is not installed, the hot water outlet valve can be opened a little to relieve the pressure, which can also avoid the leakage of the one-way safety valve.

After the circuit of the storage electric water heater is turned on and working, it can not produce hot water immediately, and it takes about 20-40 minutes to produce hot water. [smiles].

If my answer is helpful to you, please give a thumbs up (rate it in the bottom left corner), look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. If you feel that my answer is still satisfactory, you can click on my avatar for one-on-one consultation. Finally, I wish you good health and a good mood!

The leakage of the angle valve is the problem of the angle valve, and it has nothing to do with the water pipeline in the wall.

Since it has been found that the angle valve is leaking, it is necessary to try to replace the angle valve with a new one, and see if it can solve the problem after replacement.

If the problem still can't be solved, it is necessary to find a local experienced plumber to check and confirm the site and deal with it appropriately.

Summary. What is going on with the leakage of the water inlet valve of the water heater 1, the wear of the inlet valve core will cause its water leakage, if it is caused by this reason, we can turn off the water heater, remove the water inlet valve, and replace it with a new valve core or a new inlet valve.

What is the matter with the water heater inlet hydroponic valve leakage 1, the inlet valve core wear will cause its water leakage, if this is the reason, we can match the bureau to turn off the water heater, dismantle the water inlet valve, and replace it with a new valve core or a new inlet valve.

2. The water heater inlet valve leaks, and it may be caused by the poor connection and sealing between the valve and the water pipe. When installing the hose, we can wrap the raw material tape around the threads of the connection and tighten the hole. 3. If the valve at the water inlet of the water heater is leaking, then it shows how much water pressure is inside the water heater, which causes the pressure relief valve at the water inlet to drip and depressurize.

We can turn off the inlet valve of the water heater, turn on the shower, etc., drain some of the water in the water heater, and then open the inlet valve.

The water heater drain valve keeps dripping water can be caused by a poor seal of the valve or fouling inside the valve. Here's how to fix it:

1.Check whether the valve is tight: first close the water inlet valve and power switch of the water heater, and then use a wrench or pliers to tighten the Zhihu Meng drain to make the excitation valve to see if it can solve the problem.

2.Replace the valve: If it still drips after tightening, it may be that the valve is not tightly sealed and needs to be replaced with a new valve.

3.Clean the valve: If the scale inside the valve causes dripping, you can use acetic acid or citric acid solution to clean the valve, remove the valve and soak it in the solution, clean it and then install it back.

4.Ask a professional to repair it: If none of the above methods can solve the problem, it is recommended to ask a professional to repair or replace the water heater.