What do you need to prepare before using your DJI drone?

Preparation steps before the take-off of the Xinjiang elves:

1.Check that the remote controller, Intelligent Flight Battery, and mobile device are fully charged before takeoff.

2.Whether the propellers are installed correctly.

3.Make sure a micro-SD card is inserted.

4.Whether the camera and gimbal work normally after the power is turned on.

5.Calibrate the compass after powering on and check if the motor starts normally.

7.Whether the surrounding environment meets the flight conditions (it is recommended to be in an open field, avoid tall buildings, crowds).

Please pay attention to the following points when flying the aircraft:

1. Please observe the flight environment before takeoff.

2. Please calibrate the compass and IMU before takeoff.

3. Please set the appropriate return altitude and pay attention to the prompt of automatic return to home when the battery is low.

4. Power on the aircraft on the ground, do not power on during shaking, otherwise it will cause the aircraft's heading axis to drift.

5. Turn on the multi-mode switch in the DJI Go app, and manually switch to attitude mode after the aircraft compass is disturbed, which will turn off the work of the compass and GPS module. In this case, the auto-return function is invalid.

6. Try to be as soft as possible when the remote controller hits the lever, and under normal circumstances, do not continue to fly with the full pole to avoid drifting too fast due to excessive inertia when the aircraft turns. Prevent errors in judgment and ensure flight safety.

The aircraft can take off in the following ways:

* When the aircraft lands, pull the throttle stick to the lowest position and hold it for a few seconds before the motor stops.

[Aerial Photography Aircraft Series]: Aircraft, remote controller, and goggles should short press the battery switch once, and then press and hold the battery switch for more than 1 second to turn on and off;

Power on and off. The aircraft is powered on.

Press (release) briefly (release) and then press and hold the power button for about 1 second to turn on the aircraft.

The aircraft is powered off.

When the aircraft is powered on, press (release) briefly (release) and then press and hold the power button for about 1 second to turn off the aircraft.

The method of turning on and off the remote controller is the same as that of the aircraft.

Takeoff. After the aircraft is powered on and connected to the remote controller, it can take off in one of the following ways:

Automatic take-off. dji fly

Please click Enter a description.

dji go 4

Please click Enter a description.

Manual take-off. After the aircraft is turned on, the remote controller will play the lever for about 2 seconds according to the diagram below, and the propellers will start to rotate. Then hit the ascending rod and the aircraft can take off.

Please click Enter a description.

Taking the American hand as an example, the rising lever is the left joystick of the remote control, and the aircraft can take off by pushing the joystick upwards.

Please click Enter a description.

Landing. Automatic landing.

When the aircraft returns to the vicinity of the Home Point and is in the air of a landable location, tap the button on the flight interface of the DJI FLY app, and then press and hold "Land", and the aircraft enters automatic landing.

Landing manually. After the aircraft returns to home, or needs to land after the flight (at this time, the aircraft is already in the air of the landing place), you can push the left joystick down, and the aircraft will slowly descend, and when descending to the ground, continue to push the joystick downwards for about 3 seconds to stop the motor, and the aircraft will complete the landing.

1. Install the battery in the main slot on the drone.

2. Use the data cable to connect with the tablet or mobile phone to install the software.

3. Install the rotors.

4. Press the power button of the remote control, and then press and hold the button to turn it on.

5. During take-off operation, the double rod is pressed to the middle and bottom (45° angle into an inverted figure-eight shape) at the same time.

6. Flight control, the left rod is up and down, and the fuselage rotates.

Go directly to the flight interface, select the aircraft icon, enter the "flight control parameter settings", and click to cancel the novice mode.

DJI. Precautions for drone starter mode:

1. Read the user manual to eliminate common problems for novices.

On the product page of DJI's official website, you can find the official user manual, quick start guide, and tutorial content in the ** area. Read the user guide carefully to understand the aircraft's functions, operating environment, and precautions.

2. Practice flight simulation and understand basic flight operations.

Before flying, you can use the flight simulation function in DJI GO and DJI GO4 app to more intuitively understand the flight attitude and direction changes corresponding to the remote controller's stick operation.

3. Novice mode first practice.

When activating the aircraft, the app will prompt you whether to turn on the novice mode to limit the flight distance, altitude and speed of the aircraft. Novices are advised not to turn off this mode to ensure that the aircraft can fly within visual range.