How to get the best leakage around the bathroom pipes

Method (1) Beat glass glue.

The so-called glass glue is that we use glass glue to close the surrounding area of the floor drain. Because there may be a gap between the floor drain and the surrounding area when it is installed, if this gap is not tight, the water will seep underneath. At the same time, there is a gap between the pipe and the floor slab, and the water goes down this gap.

So we can deal with this problem by blocking the water source.

Operation steps: First clean up the floor drain around. We can use tools such as wallpaper knives to loosen the perimeter of the floor drain and then clean out the cement mortar inside.

If there is water in the crevices around the floor drain, wipe it dry with a dry rag and then use a hair dryer to dry as much water as possible. , glass glue. Then we use glass glue to fill in these gaps.

At this time, the key to our operation is to ensure that the glass glue and floor drain, as well as the ceramic tile can be made to have a close combination. In this way, the gap is sealed.

Points to note: Before hitting the glass glue, the gap must be cleaned, and the depth should be at least 5mm. In this way, the filling of glass glue can be ensured.

When we make glass glue, it is recommended that you stick a circle of masking paper around the floor drain, and then go to the glass glue. For the type of glass glue, it is recommended that you choose neutral, so that the taste is relatively small and the viscosity is very good. When playing glass glue, be sure to keep no water around the gap, otherwise the glass glue will not stick.

Method (2) Jar glue.

All glue filling is the use of permeable waterproof adhesive to avoid smashing tiles to fill joints. In this way, glue is used to penetrate into the inside of the gaps, so as to seal these gaps, and it is also effective in preventing the penetration of water. This method is actually the simplest and easiest to operate.

Operation steps: We must first wipe the floor drain around it, and there should be no floating sand particles. If there is water, try to clean it as much as possible, and there should be no open water.

Second, we go to buy waterproof adhesive for non-wipe tiles. Because we are only plugging the perimeter of the floor drain, the dosage is very small. Then pour the glue into the gap until all the gaps are filled with glue.

Stagnation for a day or two. That said, try not to drain the floor for a day or two, and don't let the drain have water around it. This ensures that the glue can solidify naturally and achieve the best impermeability.

Pay attention to the problem: When using the waterproof adhesive that does not smash the tiles, it is necessary to ensure that there is no water in the gaps. This is also the most important point.

After we finish pouring glue, if allowed, we will apply a layer of glass glue directly on top. In this way, double protection is achieved, and the effect will be better.

The leakage around the toilet sewer pipe is caused by not doing waterproofing seriously or not doing waterproofing.

The current maintenance method is to remove the tiles around the pipe, and remove the cement mortar that lays the tiles, and then it is best to use membrane waterproof material to make the perimeter of the water pipe, and the diameter should reach 60 cm. Then do a closed water test for 24 hours, if there is no more leakage, you can re-install the tiles, so that you can permanently no longer leak.

If it is troublesome to remove the tiles, it is necessary to make waterproof nails at the leakage, which also requires professional construction, and it is not good to do it yourself. But it saves a lot of trouble, but the effect is not as good as removing the floor tiles and re-waterproofing.

Hello <> toilet drain around the drain pipe is as follows: 1. The tiles around the sewer pipe should be warped first, and the surrounding dirt should be cleaned up. 2. Apply an appropriate amount of plugging phase balance around the pipeline, and it needs to be smooth. 3. Apply waterproof mortar on the surface 3 times, and each time you must wait for the last time to dry thoroughly before you can continue construction.

4. After the construction is completed, a closed water test should be done on the ground to ensure that there will be no water seepage, and new tiles should be laid around the toilet sewer pipe. Pro-<>

There is often a problem of water leakage in the bathroom, and if the waterproofing work of the bathroom is not done well at the beginning, the probability of water leakage will be greatly increased, which will not only flood the home, but also may affect the residents downstairs. What is the cause of a water leak in the bathroom, and how to solve it?

1. Reasons for water leakage in the bathroom.

1. It may be that there is a leakage in the pipeline, for example, there is a crack in the connection pipe or the wrapped raw material belt is loose, and it will slowly leak down the pipeline.

2. If there is a leakage problem in the sewer pipe of the bathroom, it may be that the sewer pipe is damaged, or there is a problem at the joint between the sewer pipe and the ground, and the water seepage will slowly occur in the later stage.

3. The bathroom is not waterproof, and waterproofing is very important, because the frequency of water use in the bathroom is relatively high, in case the waterproof project is not done, there will be water leakage in the later stage.

2. How to solve the leakage of water pipes in the bathroom.

1. To re-do the waterproofing, re-do the waterproofing, the amount of work is still relatively large, but in order to have the problem of water leakage in the future, I think it is very necessary. The original tiles should be removed, the ground should be cleaned again, and then in accordance with the relevant proportions, after the cement mortar ratio is successful, the ground should be leveled, and then waterproof, and the height of the waterproof should also meet the requirements, generally speaking, it should reach more than 20 cm, and then it is necessary to do a closed water test to ensure that there is no longer a water leakage problem, and then paste the tiles.

2. Next, the water pipe needs to be treated, the leakage point needs to be found, and then the water pipe needs to be rearranged, if the water pipe has been broken, the pipe needs to be replaced. When laying pipes in the wall, a groove should be made, and then the groove should be made of waterproof material, which can also effectively avoid water leakage again.

I concluded: If there is a leakage of the bathroom water pipe, you first need to find out whether it is a problem with the pipe, or the bathroom waterproof work is not done well, and then solve it accordingly. Sometimes, it is necessary to choose high-quality pipes, which can also reduce the problem of leaking water pipes in the bathroom.

Whether it's a public restroom or a family bathroom, the most important thing is to do a good job of waterproofing. Go and choose waterproof tiles, waterproof stickers and more. And if there is a leak around the drainage pipe in the drainage system, the entire waterproof layer will work.

Toilet drain around the leakage treatment method:

1. External treatment: Seal around the drainage pipe, water cannot enter, and naturally it will not seep out.

2. Inside**: Fill the perimeter of the drainage pipe with a flexible waterproof agent, or you can use gypsum water to fill it - the material is cheap and easy to obtain; Use polyurethane styrofoam or sealant to beat the surrounding, and finally treat it with water-resistant putty or cement slurry at the treatment position, and then press the sanitary ware, and make a splash around the sealant.

If it is a PVC water pipe, you can buy a PVC water pipe to connect it yourself, first cut the broken pipe, put the interface into one end of the pipe first, so that the cutting position of the other end is just flush with the other opening of the interface, so that it can be straightened, and then send it directly to this end, so that both ends have a certain cross distance (length) and then disassemble it, and use PVC glue to apply it to the inside of the two ends and the outside of the two sewer pipes.

In the toilet safety knowledge, the bathroom waterproof experiment is as follows:

1.Pay attention to the waterproof treatment of the seams. The joints between the spine wall and the floor in the bathroom, as well as the joints between the pipes and the floor, are often a mistake-prone link. In the construction process, we must urge the construction personnel to do the work carefully.

2.After the waterproofing treatment is done, finally do a waterproofing experiment. The owner can block all the drains in the bathroom and circumference the doorway about 20 cm high.

After 24 hours, re-check for leakage. This 24-hour waterproof experiment is currently being promoted in the industry.

3.It is best to use a waterproof socket with a buckle box. Because there is more water in the bathroom, it is possible to ensure the safety of electricity to the greatest extent with the socket of the buckle box. Homeowners may also consider placing restroom power switches and outlets outside the restroom.

Finally, it is recommended that due to the small space in the bathroom, it is best to use small wall and floor tiles in order to make the interior of the bathroom more harmonious.

Bathroom pipe leakage should first find the cause of the leakage, and then solve the problem in a targeted manner.

1. If the leakage of the toilet water pipe is caused by cracks in the sewer pipe body, the leakage should be blocked with a plugging agent, or the pipe body should be directly replaced with a new one. Tsai Zhengshi.

2. If the leakage of the toilet water pipe is caused by the aging and damage of the waterproof tape at the faucet connection position, you should use a new waterproof tape to reconnect the interface position, or replace the connection accessories with a new one.

3. If the leakage of the toilet water pipe is caused by the aging and damage of the sewer pipe under the washbasin, the sewer pipe should be directly replaced with a new one, and effective sealing measures must be taken at the interface position when replacing.

4. If the leakage of the toilet water pipe is caused by the rupture of the water pipe in the ground or wall, the wall or the ground should be chiseled, and then the leaking pipe should be found, and then the leaking pipe should be replaced with a new one.

Precautions for installing toilet water pipes

1. In order to improve the decorative effect in the bathroom, it is recommended to change the exposed water pipe to a concealed water pipe, so that the overall appearance of the bathroom can be more beautiful. In order to use convenient hot water, it is recommended to install a hot water pipe in your home.

2. If the user uses a gas water heater at home, Qingwu should install the water heater in the kitchen, and then lead a long pipeline from the water heater to the sanitary limb room. If you want to install hot and cold water pipes, it is best to choose a water pipe made of PPR, which will have better pressure resistance and heat resistance.

<> if the main pipeline is a PVC pipe, you can buy a PVC pipe of the same model when the water leaks and replace it yourself, if the leakage is relatively small, you can use waterproof tape to wrap a few more times around the leaking part, and then use cement mortar or waterproof paint to wipe it on. If there is a leak in the joint of the water pipe, it is very likely that the joint itself is broken and needs to be replaced with a new one. If the iron pipe leaks, the diameter of the water pipe is not the same, and the solution is not the same, and if it is inconvenient to replace it, you can find a professional to repair it.