What are the basic steps for novice automatic transmission training?

1. One dial, two steps and three gears; 2. Four songs, five pines and six observations; 3. Seven lifts, eight steps and nine back lights.

Introduction:

1. Automatic gear starts.

First toggle the gear to N gear (i.e. neutral) and press the brake, and then put D gear (forward gear) after the car starts; Honk your horn before you get ready to start, then release the handbrake and observe that there are obstacles around. Lift the brakes with your feet loose, press the accelerator pedal lightly, and return to the turn signal after the car slowly drives off the road.

2. Automatic stopping.

Novice automatic car driving tips remind that if the parking time is very short, you can press the brake pedal in D gear to stop, so that you can release the brake pedal to start immediately. If you stop for a little longer, you can apply the handbrake while pressing the brake pedal in D gear. For longer periods of time, it is best to put the gear selector lever in N gear and release the brake pedal after tightening the handbrake.

3. Automatic transmission and reversing.

When novices need to reverse while driving an automatic transmission, they should move the gear selector lever to R gear after the car is completely stopped, otherwise it will damage the shift actuator or the parking lock mechanism in the automatic transmission. If you are reversing on a flat road, you can slow down at the idle speed of the engine after releasing the brake pedal and hand brake, without pressing the accelerator pedal. If you want to cross steps or other obstacles while reversing, you should press the accelerator pedal slowly and brake in time after crossing the obstacle.

When you were taking the driver's license test, the master taught you. Here you can write down the meanings of the commonly used letter representations: P stop, D forward gear, n neutral, r reverse. Hope mine is helpful to you.

1. Get in the driver's seat and press the brake pedal.

2. Press and hold the "one-key start" button (press once for the power switch, and press and hold for 3-5 seconds to start the engine).

3. Gear up, according to the need to move forward or reverse, the gear is operated. Then release the electronic handbrake (lift it lightly and press it).

Fourth, release the brake pedal, the vehicle moves, and the start is completed.

5. When the engine is about to turn off, slowly step on the brake and gradually slow down until it stops.

6. Hang the gear on the n gear.

7. The electronic handbrake is pulled up.

8. Press the "one-key start" button to turn off the engine and power.

Beginner automatic transmission tutorial:

Before the vehicle starts, make sure that the target is in P or N gear, and pay attention to the brake and handbrake when starting.

It should be well coordinated with the throttle, hang up the D gear, and release the brake at the same time to slow up, which is equivalent to a manual gear.

Slow-lift clutch.

In the process of opening the automatic transmission, when going uphill and climbing, the driver should change the "D gear" when getting used to the knotting and bending bundle, especially when climbing, only the use of the D gear, the driver will obviously feel that the car is more powerless, can not increase the speed, at this time may as well take a step back, use the climbing gear to climb the hill in low gear, the car not only runs very strong, but also drives faster;

Use low-speed imaginary gear at the right time, when driving on a ramp, open the automatic gear to D gear, sometimes the resistance is large, the throttle can't keep up with the decrease in speed, when the speed drops to a certain extent, the transmission.

It automatically reduces one gear, then adds throttle drive force greater than drag to accelerate the car, and so on to a certain speed when it rises to a high position.

Automatic transmission, as the name suggests, does not require the driver to manually change gears, and the vehicle will automatically select the appropriate gear according to the speed and traffic conditions traveling.

Driving. Automatic cars in general.

There are six positions in the upper gear, from top to bottom: P, R, N, D, S, L.

Cars with automatic transmissions only use parking gear, P gear, reverse gear, R gear, and neutral gear.

N gear, forward gear D gear can fully meet the needs of general driving, and if you encounter some special driving environment, you need to use other function gears. Therefore, if you are able to choose the right way to control the controls, the car with an automatic transmission will perform better than the manual transmission.

Steps to start learning to drive for novice automatic transmission:

1. Step on the clutch pedal with your left foot and put the gear lever into low gear with your right hand. In the case of a blind calendar, the empty car can start on a flat and solid road, 2 gears can be used, and heavy vehicles can be used 1 or 2 gears depending on the situation;

2. Turn on the left turn signal, whine, observe the surrounding situation, confirm the safety, hold the steering wheel steadily, and release the hand brake lever;

3. Relax the clutch pedal with the left foot according to the essentials of "fast stop and slow", and slowly step on the accelerator pedal at the same time to make the vehicle start smoothly, and turn off the turn signal after entering the normal driving route.

The correct way to start for automatic transmission novices is as follows:

1. After the driver sits in the driver's seat, he does not need to step on the brakes, directly press the start button, the ACC light is on at this time, and then press it more, and the vehicle will conduct a self-test at this time; It is recommended not to skip the self-test step every time you start cold, and you can choose to skip the hot start.

2. Step on the brake and press the start button again to start the ignition; Under normal circumstances, the engine will start within 3 seconds of pressing the ignition switch, if the engine is difficult to start, do not start frequently, let the starter rest for a while every 5 times to avoid burning out the starter.

3. Release the foot brake, you can choose to heat the car in situ, and the time can be determined according to the environment; Specifically, you can look at the water temperature gauge on the instrument, when the water temperature reaches and stabilizes at about 90 degrees, it means that the hot car has been completed.

4. Step on the pedal again, hang D gear, and release the handbrake (the electronic handbrake can be short-pressed directly); Before starting, look in the rearview mirror to see if the road conditions are suitable for starting, and also honk your horn and turn signal to alert other vehicles and pedestrians.

5. Slowly release the foot brake and start; After starting, you should drive quickly into the road and drive at the prescribed speed.

Introduction of automatic transmission

Automatic transmission, as the name suggests, does not require the driver to manually change gears, and the vehicle will automatically select the appropriate gear according to the speed and traffic conditions. There are six gears on a general automatic transmission car, from top to bottom: P, R, N, D, S, and L.

When starting in automatic transmission, don't step on the accelerator too hard, because the automatic transmission starts with a fixed speed, so no matter how you step on the accelerator with a lot of sleepiness, it is a fixed speed shift. Moreover, the automatic transmission has a speed protection function. If you rev too high, it won't shift up even when it reaches the gear speed to protect the engine.

It's as if you're always in first gear to run the most appropriate start. You should press the throttle lightly first, release it and then press the throttle a little harder. Beginner practice automatic transmission tutorial:

1。Pay attention to the automatic transmission when starting. Before the vehicle starts, make sure the target is P or N, and pay attention to braking when starting.

The handbrake and throttle should be well coordinated, and the D gear should be hung. At the same time, release the brakes and slowly rise (equivalent to a manual gearbox slow up clutch); 2.In the process of driving an automatic transmission, when going uphill or climbing, the driver should shift to "D gear" at the end of the habit.

Especially when climbing, only when using D gear, the driver will obviously feel that the car is more weak and unable to speed up. At this point, it is advisable to take a step back and climb in climb gear (low gear). The car will not only run fiercely, but also drive faster; 3.

Use low gear when appropriate. When driving on a ramp, turn the automatic into D mode. Sometimes there is a lot of resistance, and the throttle can't keep up with the deceleration.

When the speed of the vehicle is reduced to a certain level, the gearbox automatically lowers one gear, and then the driving force of the throttle is greater than the resistance, which causes the vehicle to accelerate, thus gaining a certain speed when rising to a higher level.