iPhone6s can still be used when the screen is flooded?

Apple 6s can still be used if dropped into the water if it is dealt with in time.

Let's talk about how to deal with it first, the first water ingress must be turned off first to prevent the motherboard from burning out;

The second is to dry the mobile phone from beginning to end, use a cotton swab to get the gap in and absorb it, and the third is to put a paper towel or bag in the rice jar and seal it for 2 days to let the moisture absorb dry.

The above three steps are what Xiaobai should do, after all, Apple is a whole machine and can't remove the battery by itself, so it can only do this.

But what happens after 2 days?

If it is not serious, it can be used normally, but if it is serious, it will have a blurred screen, a black screen, and various small problems.

In fact, regardless of whether it is used normally or not, there is still water inside our mobile phones, and this water will definitely not be absorbed by rice so easily. Even if it is displayed normally now, the mobile phone is working with illness, and it may crash or even be scrapped at any time.

Because the water enters the circuit of the motherboard, if you don't disassemble the machine and do an internal cleaning with plate washing water and ultra-green wave, it will slowly oxidize and rust, and wait until a certain time, so many lines only need a short circuit, the entire motherboard will be wasted, and it is irreparable. Because by that time, all the lines would be almost rusty.

Therefore, we must take the water inlet machine to disassemble and clean it as soon as possible, and the other thing is that the water inlet machine apple is not guaranteed, which is artificial. And there are some labels in the Apple phone, as long as the water enters, those labels will turn red. Apple will not have a warranty after sale.

It can only be repaired by a mechanic master. Because it is very annoying to do the whole machine cleaning process, the internal fine parts need to be dismantled by professional equipment to clean and dry, and many places are troublesome, only a few large pieces are cleaned up, and the fine cleaning can not be done. And basically there are no ultrasonic instruments to remove water in those places.

There are so many tiny parts, just by a hair dryer to blow, it is useless. So why there will be problems after a while after many water inlet machines have been cleaned, this is also the reason.

If the screen goes black, most of them are broken by the power supply of the motherboard or the baseband of the CPU hard disk. This can only be repaired by experienced masters. Most small shops can give you a replacement part, after all, it is only a disassembly and assembly, which is relatively easy, but to repair at the chip level, it is a headache, and most of the answers are that it cannot be repaired or returned to the factory.

Their so-called factories are factories and stores with equipment and machines here in Guangzhou. I have been opening an Apple repair center factory store in Guangzhou, and I still know a lot about this.

Maintenance**, depending on the severity, cleaning ** is not expensive, about 100 yuan is OK, the key is to design to the maintenance of large pieces, iphone6s are basically hundreds to thousands.

How to deal with the water after the iPhone is ingressive.

1.Turn off the phone as soon as possible, cut off the power, and do not try to turn it on again to avoid causing a short circuit in the motherboard.

2.Remove the SIM card and use a tissue or cloth to remove water from the outside and crevices of the phone.

3.If there is light water ingress, you can wrap the phone with a paper towel, put it in a bag and put it in a small bag of desiccant.

4.The mobile phone cannot be turned on after entering the water, most of the chips such as the motherboard and CPU are short-circuited and burned, and it is recommended to send it to the after-sales service center for repair immediately.

Don't try the following wrong methods after your phone gets into water.

1.Don't shake your phone too hard. Because under the constant shaking, the liquid will swim inside the machine, and the moisture may enter deeper and burn the internal chip of the machine.

2.Don't use the hot air of a hair dryer to dry your phone for a long time. iPhones are now all metal bodies, and metal conducts heat easily, which will blow off the solder joints of the motherboard inside the machine, causing the motherboard to malfunction.

3.Do not attempt to charge a phone that has been flooded. An iPhone that gets into the water may have water stains inside, which can burn out the motherboard when it is powered on and cause a more serious failure.

4.Do not leave your phone in water for a long time. In the case that it cannot be used normally after two or three days after general treatment, it should be sent for repair immediately, and long-term placement will cause the motherboard to be corroded, or even unable to be repaired.

It is recommended to restart the phone to see if it can be used normally, if not, it means that this is a kind of screen blurry, and the reasons and solutions for the blurry screen are as follows:

1. If the cable of the mobile phone is broken, the cable connecting the screen and the motherboard is burned or the contact is poor, so it is good to go to the after-sales store to replace it.

2. The screen is broken and the screen needs to be replaced, ** higher.

3. The motherboard is broken, this probability is relatively small, but it is not ruled out that the solution is to replace the motherboard, which can be repaired by Apple. It is mainly caused by the failure of the screen group, that is, the problem of the screen line IC.

If the after-sales service of the water inlet machine is generally not warranted, there is a water inlet sticker inside the machine.

It can also be repaired after sale, but ** is similar to buying a new one.

Outside repairs are generally hundreds or thousands.

It is impossible to repair it yourself, and the maintenance of the water inlet machine depends on the character, and it may not be possible to repair the original, and only some resistors and capacitors can be used, and the general chips are different.

At present, the iPhone is still the well-deserved king of arcades in terms of market popularity. It inherits most of Apple's advanced technology, which makes people love it. It is because the technology and technology are too sophisticated,So the presentation of the problem is also varied,I have introduced to you before the disposal method of the headphones and speakers caused by water ingress without sound,Today I will introduce you to the situation,Water incurs the situation of the flower screen。

What to do if the iPhone gets into the water.

The above is the iPhone that causes the screen to be blurred after entering the water, after booting and entering the system, it is obvious that the color difference between the screen and the screen is huge, and it is very easy to incur the shortcomings of the mobile phone screen failure, which affects the use very much.

There are two types of phone water damage repairs:

1: The interface is corroded by water, and it can be dealt with only by changing the interface.

Two: The interface cannot be changed, so the screen needs to be changed.

The above is the shortcomings of the iPhone water splash screen and the precautions for disposal after water ingress, I hope to help the little companions.

You can sell your current phone at a low price (with the lowest economic loss).

1.Do not try to turn on the device immediately if there is water ingress. Because the iPhone has a built-in battery that cannot be removed, the motherboard will be short-circuited if it gets into the water, and if it is turned on, the motherboard will be burned, causing irreparable consequences.

2.You can first use toilet paper to dry the water outside the mobile phone, and then place the mobile phone screen horizontally to prevent water from flowing to the motherboard, and then use a blow dryer to dry the water, and turn on the temperature at medium or small temperatures.

3.Wipe down the circuit board with anhydrous alcohol and try to turn it on. Because alcohol volatilizes quickly, the moisture on the circuit board can be volatilized clean.

4.Send it to the maintenance center (020-83621957) for repair as soon as possible. If the motherboard is severely corroded over time, it will cause irreparable consequences.

iphone6 mobile phone water into the screen of the treatment method:

First, after finding that the iphone6 is flooded, the power is turned off and shut down as soon as possible, and after the shutdown, it is necessary to judge how much water enters and the type of water.

Second, a small amount of water inlet type: if there is not much water intake, but there is some water in the surrounding gaps, then you can wipe it with a paper towel after shutting down, and then use the hair dryer at home to blow it gently, and then put it on the paper towel to control the water, and put it in the ventilated place for a day or so, and then turn it on again It should be no problem, the small water inlet is generally not a big problem, and the iPhone is still relatively leathery. Pay attention to the hair dryer do not use hot air to blow, do not use hot air, otherwise it is easy to burn the machine.

Third, a small amount of oil type: if it is not water but oil, it is recommended to turn off the machine at the same time, open the iphone with a screwdriver, wipe the oil dry, no matter how much oil is in, because the oil is difficult to volatilize, so the oil can not be completely clear with blowing or drying, the only way is to turn on the oil dry, and then dry it in a ventilated and dry place, and then wipe it with a paper towel after a period of time, knowing that there is no oil at all and then turn it on. Note that oil is far more terrible than water.

Third, a small amount of laundry detergent water type: laundry detergent water is somewhat corrosive, so you still have to open the mobile phone, first dry the water, and then use a soft paper towel to wipe the traces left by the laundry detergent, and put it in a ventilated place to dry for a day.

Fourth, a large amount of water inlet type: first turn on the machine by yourself, and then wipe it clean with a paper towel, if there is a lot of water inside, then you can use a cotton swab with alcohol to wipe it a little more, because the volatilization of alcohol is relatively fast, which can speed up the volatilization of water. After wiping with alcohol, dry the phone with a cool breeze from a hair dryer.

Then pick up the phone and shake the water with your hand to see if you can shake the water, if you can shake the water, and then continue to repeat the above steps. Then open the lid and put it head up in a dry and ventilated place to air dry naturally for about a week. Remember that it must be more than a week, don't turn on the machine out of curiosity in the middle, it may seem dry on the surface, but there is still water inside, so the air drying time must be long.

Pay attention to wiping, wipe the water near the battery first to prevent too much water near the battery from causing a short circuit.

Fifth, long-term immersion in water: If you accidentally put your iphone6 in the washing machine and wash it together, or soak it in water all the time. Then first dry the water yourself according to the large amount of water inlet type, and then find a special place for disassembly and maintenance, and let them wipe it clean for you.

Do not turn it on immediately after wiping it off. Take it back and continue to dry, turn it on after a week, if there is no problem at all, then you can use it with confidence, if you still can't turn it on, then continue to dry, and dry it for another week, if you can't turn it on for such a month, then iPhone6 has drowned.

Sixth, if you can occasionally turn on the computer during the period, and the white screen or flower screen after turning on the device, then the iphone6 is still saved, you can turn it on every few days and use it, and then continue to dry, knowing that there is no problem with it, the iphone6 has been cured.

First of all, for the 1st and 2nd cases, we must not think that the machine has been scrapped. Don't think it's already in the water anyway, so you disassemble it indiscriminately. The following I would like to put forward my personal suggestion for various situations, in the case of power-on, it falls into clean water, which generally does not need to be disassembled.

Turn off the power as soon as possible and shake it dry vigorously, but don't shake the machine off, the idea is to shake the water out of the screen. If there are water droplets left on the screen, there will be traces after drying. Place under a slight heat source such as a desk lamp or spotlight to let the moisture slowly dissipate.

This process takes more than six hours. Do not use a strong heat source such as a hair dryer in a hurry. After these three steps of processing, the power supply can basically work normally.

Take a hair dryer to blow first, don't turn it on or off, and then go to the after-sales point.

Originally, the water was in the water, and the screen was blurred, but I turned on it for an hour**, and the phone screen was completely fine