What are the advantages of dispensing machines?

Different from the traditional manual dispensing operation, it will be faster and more convenient to choose a dispensing machine to complete the dispensing operation, because we all know that no matter what the nature of the work, if the manual operation is selected, then it will take a long time and energy, and there is also a large error rate, which greatly reduces the production efficiency and production time, and at the same time, because the wages to be paid to the workers, which increases the production cost at another level, so it is not cost-effective; However, if you choose a dispensing machine, you don't have to worry about any mistakes at all, because its programs are set to ensure a good dispensing operation, and because it can complete all operations automatically, so that manual operation is no longer required, so it also greatly reduces the use of labor and production costs, and the production efficiency has been greatly improved.

Secondly: because we all know that the dispensing machine is a kind of mechanical equipment, so we can realize the mechanization and effective production of dispensing work, and it does not need to be combined with any other equipment to complete the dispensing work alone; At the same time, it is very simple and fast to operate, and at the same time ensures a good dispensing accuracy.

Finally: Generally speaking, inside the dispensing machine, there is a memory card that can be used by roommates to operate programs and data, that is, the SD memory card that we often see, so that we can store some of the data we need to use, and at the same time facilitate the transfer of data between some machines.

There are many advantages. It can improve efficiency.

The dispenser is to send compressed air into the plastic bottle (syringe), press the glue into the feed pipe connected to the piston chamber, when the piston is in the upper stroke, the piston chamber is filled with glue, when the piston pushes down the dispensing needle, the glue is pressed out from the needle nozzle. The amount of glue discharged is determined by the distance at which the piston is downpunched and can be adjusted manually or controlled in the software.

The dispenser can be divided into two working modes:

1. Manual dispensing: manually use the principle of manual dispensing machine to dispense on electronic products, the process method is simple, low cost, the disadvantage is that the dispensing efficiency is slow, and a lot of labor will be consumed.

2. Automatic dispensing: The principle of FISNAR dispensing machine is to use air pressure to push out the glue within a set time. The instrument controls the time of each injection to ensure that the amount of each injection is the same, as long as the air pressure, time and selection of the appropriate needle nozzle are adjusted, the amount of each injection can be easily changed, which is convenient and accurate.

The working principle of the dispensing machine: compressed air is fed into the plastic bottle (syringe), the glue is pressed into the feed tube connected to the piston chamber, when the piston is in the upper stroke, the piston chamber is filled with glue, and when the piston pushes down the dispensing needle, the glue is pressed out from the needle nozzle. The amount of glue dripping is determined by the distance of the piston downflush and can be adjusted manually or automatically controlled in the software.

Features: High speed, low sensitivity to adhesive viscosity.

Advantages: It can increase the dispensing speed, improve the dispensing environment, and improve the dispensing quality.

Dispensing machines, also known as glue applicators, glue dropping machines, glue punching machines, glue filling machines, etc., are specially designed to control fluids. The automatic machine that drip and coat the surface of the product or the inside of the product can realize three-dimensional and four-dimensional path dispensing, precise positioning, precise glue control, no wire drawing, no glue leakage, and no glue dripping. The dispensing machine is mainly used for glue, paint and other liquids in the product process to accurately point, inject, coat, and drip to the precise position of each product, and can be used to achieve dotting, line drawing, round or arc.

Hello, I know that the principle of Hangzhou Maisu Glue Molding Machine is to send compressed air into the syringe or plastic bottle, press the glue into the feed tube, and use the pressure to dispense. The amount of glue dispensed can be adjusted manually or programmed.

There's a house downstairs that says it's a bit uncertain.

Dispensers are pneumatic and are the most common on the market.

The private service glue pressing system is a bright spot in the recent dispensing machine industry, and Shenzhen Shichun is the earliest manufacturer of this kind of system, which can be referred to.

The typical application of motion control, the traditional dispensing process is integrated into the motion control system, which is perfect, and it is relatively mature in China! @

The principle is the same as that of a syringe

At present, the dispenser mainly uses air pressure to push the glue out, and the SAMON dispenser sends compressed air into the plastic bottle (syringe), presses the glue into the feed pipe, and the glue flows through a screw that rotates at a fixed time and a specific speed. The rotation of the screw creates a shear force on the adhesive, which makes the adhesive flow down the thread, and the rotation of the screw continuously pressurizes the adhesive to make it flow out of the tip of the dispensing needle. Features:

It has the flexibility of no fixed limit on the dot size. It can be adjusted by software. However, when dripping large glue dots, the screw rotation time is long, which will reduce the output of the whole machine.

In addition, the viscosity and flow characteristics of the adhesive can affect its stability. Harmon Technology.

Seriously answer:

The dispensing machine is divided into several parts: hardware, software, and glue.

Hardware:

Automatic machine (dispensing table - including slide rail, wire gauge, motion control host, controller, teach pendant), dispensing valve (needle, needle valve; screw valves; piezo valves; Dispensing controller, etc.) Other auxiliary equipment: air compressors, connecting pipelines, etc.;

Software: Control software1. By studying the characteristics of the product, select glue and put it into a glue bucket;

2. After setting the dispensing path, start dispensing;

3. The glue passes through the dispensing valve, sprays and dispenses to the surface of the product;

4. UV curing, baking, natural curing, etc., to complete the dispensing process.

Therefore, the principle of the dispensing machine is through the combination of software and hardware, through the software calculation and planning path, and the hardware through the air pump to stabilize the glue, and then to achieve the completion of dispensing.

How the dispenser works: After the power is on, the glue valve heats up, and the glue is put in to preheat and prepare for the fluidity of the glue. There is a pneumatic compressor compressed air into the hose syringe, the compressed air pressure sends the glue into the piston and the feed pipe, the air pressure impacts the glue in the piston and pushes it down into the needle, controls the mechanical operation through the control programming into the route track that has been programmed, adjusts the amount of glue through the distance pushed down by the piston, and continuously presses back the gap in the middle of the air pressure to adjust the dispensing speed of dispensing.

The current development direction of dispensing machines is destined to be automation and high precision. If you want to achieve automation and high precision, the first thing to do is to understand the dispensing machine, only by understanding the dispensing machine, can you reasonably use the dispensing machine and improve the dispensing machine. Below we will work together to **, how the dispensing machine performs the dispensing operation.

The first step is to send compressed air to a syringe or a plastic bottle. Before that, it is necessary to ensure that the syringe or plastic bottle is clean and free of contamination. In daily dispensing operations, care should be taken not to mix different glues in one container.

If there is a requirement for mixing and dispensing, the cartridge should be cleaned in time after mixing. After using the glue, place the glue in a cool, ventilated and dry place that is not easy to touch. Tighten the rubber cap to prevent colloid leakage.

When there is a large amount of leakage, it can be cured with water and then scraped off.

The next step is how to press the glue into the feed pipe connected to the piston chamber. In the compression process, the scope of compression, the specification of the style, and the requirements for the surface all directly affect the quality of the lamination. The relevant variables should be strictly controlled to ensure the quality of dispensing.

In the glue lamination process, the glue is pressed into the pipeline, and the needle flows out in a state or spot shape according to the dispensing requirements for a short stay in the pipeline. When the piston is in the upstroke, the piston chamber is filled with pre-added glue. When the piston is pushed down on the dispensing needle, the glue is squeezed and pressed out of the nozzle.

The final process is glue discharge. In the process of dispensing, there is often a phenomenon that the size of the glue is inconsistent or the glue is not smooth. At this time, it is necessary to check and confirm the four links.

The first is the glue ratio, many times, the glue is not smooth due to the glue is too silky. Another thing to check is the working air pressure, which should be maintained appropriately and steadily. The third thing to pay attention to is the patency of the pipeline.

The last thing to pay attention to is whether the temperature of the mating device is normal. It is important to note that the amount of glue dripping is determined by the distance the piston is downstroked and can be adjusted manually or programmed.

Abstract:The dispensing machine is a machine used to control the fluid and drip and coat the surface or interior of the product, and its main functions are to dispense and fix the object, dispense and mark the surface of the object, and dispense and conduct conductivity on precision parts such as circuit boards. The basic parameters of the dispensing machine mainly include the number of shafts, repeatability, transmission system, maximum load, dispensing range, programming mode, moving speed, etc., among which the repeatability, maximum load and other parameters are more important.

Let's take a look at the parameters of the dispensing machine. 1. What is the dispenser used for?

Dispensing machine, also known as glue coating machine, glue dispensing machine, glue punching machine, glue filling machine, is used to control the fluid, and the fluid dripping, coating on the surface of the product or inside the product automation machine, mainly used in the electronics industry, lighting industry, automotive industry, industrial electrical, solar photovoltaic, construction engineering and other fields. The main functions of the dispensing machine are:

1. Dispensing and fixing objects for bonding, such as car hardware, mobile phone screens, cameras, amplifiers, etc.

2. Dispense and identify the surface of the object, such as making clothing patterns, product logos, keyboard letters, etc.

3. Dispense and conduct precision parts such as circuit boards, and use special conductive adhesives to dispense and conduct conduction on semiconductors, PCB boards and chips.

2. What are the important parameters of the dispensing machine?

As a kind of mechanical equipment, the dispensing machine has corresponding parameters, and the basic parameters of the dispensing machine are:

1. Number of axes: that is, the dispensing machine is several axes.

2. Repeatability: refers to the maximum deviation value of the result corresponding to the same change process repeated by the dispensing machine for many times. This corresponds to the maximum deviation of an intact dispenser from multiple runs.

3. Transmission system: the origin of the internal kinetic energy of the dispensing machine.

4. Maximum load: the weight capacity of the Y-axis Z bearing of the dispensing machine.

5. Dispensing range: the maximum distance that can be reached by the machine dispensing, which is similar to the running memory of a mobile phone.

6. Programming method: that is, what system is controlled.

7. Program record capacity: the maximum number of groups of programs that can be stored.

8. Movement speed: The unit is generally millimeters per second, the distance traveled per second.

9. Air supply requirements: air pressure.

10. Operation mode: point-to-point, continuous line, plane auspicious orange all images, points, and straight lines can be theoretically realized.

11. Transmission mode: The transmission system gives a signal, how to do the following parts to achieve this function.

12. Signal: input and output.

13. External control interface: the interface between the screen commonly used by the dispenser and the main chassis.

Among these basic parameters, the dispensing range, repeatability accuracy, moving speed, operating system, programming mode, etc. are the more important parameters of the dispensing machine.

Dispensing machine is a kind of equipment that can accurately control dispensing socks, glue injection or gluing, and is often used in many fields such as electronics industry, lighting industry, automotive industry, file Suiye electrical, solar photovoltaic, construction engineering, hardware, home appliances and so on. It can accurately dove, inject, coat and drip glue, paint or other liquids to the corresponding position of each product to meet the accuracy requirements of the product process.

When choosing the right dispenser, you need to consider the following factors:

Dispensing needs: Determine the type of glue that needs to be dispensed, as well as the accuracy and speed requirements for dispensing.

Production line requirements: According to the product size, output, production line configuration and other factors, select the appropriate dispenser model and specification.

Working environment: Consider the working environment of the dispenser, such as temperature, humidity, dust, etc., and choose a dispenser that adapts to the environment.

Cost: According to the budget and production needs, choose the cost-effective and sensitive Yuyin Qiaoyan dispensing machine.

Brand and service: Choose a well-known brand of dispensing machine, you can get better after-sales service and technical support.

To sum up, choosing the right dispensing machine needs to comprehensively consider factors such as dispensing needs, production line needs, working environment dismantling, cost, brand and service.

The laser in the dispenser is also the laser, and there are many functions depending on what you are used for, and it generally has the following uses: 1. Laser positioning, that is, visual function.

Positioning scans are fine.

2. Laser welding.

Welding is carried out with a laser that generates high temperatures.

3 for glue.

Dispenser:It is to apply the glue to the product according to the preset path to achieve the purpose of bonding, fixing, waterproofing, and anti-vibration. It is divided into several parts: dispensing machine hardware, dispensing software, dispensing valve and controller, and glue.

Dispensing is to dispense and coat UV glue, conductive glue, heat dissipation glue, and AB glue to the designated position of the workpiece through the dispensing device.

There are three modules involved:

Dispensing hardware: dispensing machine (manual, automatic, and some machines with visual, light source, height measurement module) Dispensing software: industrial control system, dispensing system, 3D glue detection system glue:

Waterproof adhesive, special adhesive, heat dissipation silicone, UV glue, conductive glue, heat dissipation glue, AB glue and so onPrinciple:

The principle is that through the cooperation of the above three modules, the dispensing hardware moves according to the preset path, the glue is produced in proportion, and the dispensing software is designed and the path is taken.

Collaborate on dispensing. Composition dispensing machine.