How does the mobile phone show that the connection does not exist when it enters Monternet?

It's because you haven't set up your mobile phone network well, and someone else will help you get it in the business hall, or call 10086 manual service to teach you, and tell him what brand your machine is, as well as the model.

It is recommended to contact the local 10086 to check whether the main switch or sub-switch of Monternet is turned off.

Did you just top up? You unplug the battery and reboot it.

Decisively call mobile customer service and ask him to refresh the network for you, or restart the phone himself. If not, check whether the phone is in arrears and is shut down. There is a situation where you have stopped the phone before and charged the phone bill.

Generally, just restart the phone. It is recommended to call customer service to ask one side first.

There may be arrears, if there is no arrears, you can turn off the computer at boot, most of them are this problem!

If there is a problem with the mobile phone, you can change the mobile phone...

GPRS call 10086 to open GPRS network settings: The first thing is to confirm the activation of GPRS in the dynamic zone or global pass, at present, China Unicom and Shenzhou Xing users can not enter the tool Settings Connection settings Access point 1 Add an access point, the connection name is "China Mobile Monternet" 2 The data bearing mode is GPRS 3 The access point name is CMWAP (lowercase) 4 Username No 5 Prompt for password No password No password does not need to be set Authentication Normal homepage.

Gateway IP Address Connection Security Close Connection Type Permanent After completing the above, press "Options" to enter "Advanced Settings" Game Phone IP Address Automatic Primary Nameserver Secondary Nameserver **Server Address (most important) **Port Number 80 (most important) Then select China Mobile Monternet as the access point in the network to access the Internet. However, the software version before it will be garbled You can also install software to surf the Internet, such as Opera cable tester Chinese Simplified Chinese version 2: The following is the setting of MMS:

1: First of all, you need to activate GPRS 2: Then go to "Connection Settings" to add a new default access point Connection Name:

China Mobile MMS Data bearer mode: GPRS Access point name: cmwap (certain lowercase) Username:

None Prompted for Password: No Password: (do not enter) Authentication:

Normal Home:

Permanent 3: After finishing, enter the "Message" Options-Settings- MMS Change the "Access Point Used" to the one you just set The other options remain the same All in your browser settings !! Look for it, and are you not good at using the Internet or only one network?

It's not good to only get on one, so that's a matter of the network, Nokia's mobile phones are generally bought when these are good ah.

The landlord is wrong, in fact, GPRS** is to be opened, you cancel the month**, but you also have to open the day** to be able to use, after you cancel the **, it is regarded as suspending all GPRS business, that is, you can't access the Internet.

Don't have an access point set up? Please make it clear, thank you.

Internet (default) There are 2 access points connected to the Internet (priority: 1) Connection name: China Unicom connects to the Internet Data bearer mode:

Packet Data Access Point Name: 3GNET Username: None Prompt for Password:

No Password: **Authentication: Normal Home:

None Using an Access Point: The parameters in the automatic advanced settings are as follows: Network Type:

None **Port Number: 0

China Unicom GPRS Internet connection (priority: 2) Connection name: China Unicom GPRS Internet connection Data bearer mode:

Packet Data Access Point Name: Uninet Username: None Prompt for Password:

No Password: **Authentication: Normal Home:

None Use an access point: After confirmation, the parameters in the advanced settings are as follows: Network Type:

None **Port number infiltration base code: 0

Generally, there are two options: "Monternet" and "GPRS", right? It would be much better to choose GPRS, which is the case with Monternet, where the speed of the big finger is slow, and sometimes you can't get in.

I went to mobile and asked, both of them belong to mobile, and there is no difference in cost. The imitation shed can be used with confidence.

That's a matter of moving. You can also try to solve it, change the settings, then pull out the SIM card, put a different card to open first, and then put the previous SIM card, and then try again. It should be fine.

Port: 80 Network Connection: Monternet Locked Status: Unlocked Access Point: CMWAP Username: Password:

First of all, you can activate the mobile GPRS for free

GPRS settings for v3:

1.Go to Access the Web - > Web Settings - > a new entry (or your existing one)2Name: Monternets.

3.Home: wap

4.Service Type: WAP

5.Gateway: 6Port: 9201

7.Domain Name: Not specified.

8.Dial-up connection: 17266

9.Username: WAP

10.Password: WAP

Access point name: CMWAP

。MMS settings for v3:

1.Access to the Internet" Web Settings" new entry.

2.Name: Mobile MMS.

3.Home: 4Service Type: WAP

5.Gateway: 6Port: 9201

7.Domain Name: Not specified.

8.Dial-up connection: 17266

9.Username: WAP

10.Password: WAP

Access point name: CMWAP

After the above is set, you have to go to the information to set it.

Info > Intermediate Function Keys > Select Info Settings > Multi ** Info Settings > Server Info > Select the first inverted "Intermediate Function Key".

1.Service: Mobile MMS or your preferred name.

2.Server:

3.Web page settings: Select the mobile MMS 4Finish.

5.Select Mobile MMS in the current server page that is returned.

Hello, first of all, you need to confirm whether the GPRS function is enabled on the mobile phone number, this is recommended to call the local 10086 to confirm. If the function has been activated, it may be a setting problem, it is recommended to operate according to the following prompts: Click "Main Page - > Settings - > Wireless and Network - > Mobile Network Settings - > Access Point Name Fan Loss", and set the following parameters, and click [Menu] to save after setting the nuclear fiber.

Name: Arbitrary.

Access point name: CMWAP

**: Port: 80 Username: Default "Not Set".

Password: Not set by default

Server: mmsc: Default.

MMS**: Default.

MMS Port: Default.

MMS Protocol: Default.

mcc: The default < 460 >

mnc: default<00>

Authentication Type: None

Access point name type: default

Thank you for your understanding.

Ask your friend to send you an MMS message and see if you can receive it. If you receive it, it means that it is activated. Check your settings! If you can't receive it, go to the business hall and ask her to help you adjust. Can't you think of that simple? Wisdom + patience = good life, I wish you a smooth solution!

Go to the business hall and give them your mobile phone! So strenuous! Just tell me that it's not good to get the money back!

You're activated, but this is **, and you have to set up your mobile phone to surf the Internet.