How to install TP LINK wireless router for Wi Line Connect?

The first-line pass has not been realized in my local area, whether he realizes it or not, the main thing you know is how he authenticates you to surf the Internet, a few examples here in Beihai, Guangzhou:

Beihai Telecom, Tietong, and Netcom all have PPPoE dial-up, TP-Link wireless routing is set up with PPPOE dialing settings at the WAN port, and after selecting PPPoE dialing, enter the account number and password routing can generally be dialed, and your computer is generally set to automatically obtain the IP address.

Beihai Mobile is the so-called web authentication method,Generally, the first web page opened after connecting to the computer from the cat will pop up a certified page,Enter the account number、Password can go online,To install the route, the WAN port of the route is set to automatically obtain the IP address,Every time all the computers connected to the route as long as there is a computer to enter the account password,Other computers can access the Internet,This is to see which computer is the first to browse the web to log in first。

Finally, there is the way to fix the IP address, but it is estimated that your so-called one-line communication should not use this method, so I won't say much here.

Put your broadband input connection on the device and you're good to go. The IP address of the incoming route is basically OR or you can directly call ** to Great Wall Broadband and ask their staff to help you install it. Installing a wireless router basically will not affect the speed of the network, I hope mine can bring you convenience.

Connect it with a network cable to set it up first. admin admin

The building mainly uses wireless routers. First of all, the line connection must be correct (nonsense). It turns out that the network cable that is plugged into the host through the cat, unplug the computer first, and don't move the cat's line.

Unplug the computer and plug it into the WAN hole (the first hole) of the wireless router. Then use another network cable to plug in the other holes of the wireless router, which one, and then plug the other end into the main unit. After getting it done.

Enter the browser and enter**or some routers**Yes will pop up the login homepage, the default username and password are adminThe landlord can change it later.

Once you are on the wireless router settings homepage. Point Setup Wizard. Select PPOE, and the next step is the username and password of the Internet access account.

Just enter it. The wireless setup will appear. There are items such as wireless state SSID channels.

The wireless status is on, and the SSID is the name of your wireless network when you search for wireless networks. It can only be set in English, making it easy to distinguish between multiple wireless networks when finding your drop, (some nonsense). All other channel modes are not set and are default.

At the bottom, there is the WPA-PSK WPA2-PSK PSK password This is the password of your wireless network, it is recommended to set a slightly more complicated one, not all 123456, because some software that cracks the password of the wireless network can crack the simpler passwords such as 123456. After that, it's time to reboot. If the landlord doesn't understand anything, you can ask.

In view of the fact that I am more verbose and careful, I will adopt it.

Pull a network cable from the mesh hole to the router's LINE excuse, and then use a network cable from the router's LAN interface to the WAN interface of the wireless router, and then a network cable from the wireless router's interface to the computer, just connect. Those names are written on the edge of the interface, just look for them. After the line is connected, turn on the computer, open the Internet Explorer, enter in the address bar, press Enter, and the account and password are admin to enter the TP-Link setting interface.

Then select the second setup wizard in the left option, select the first router after the next step to select the Internet access method, and then the next step, fill in your broadband account password, and then keep the next step OK.

After the power is turned on, connect the wireless router to the computer, open the browser and enter in the address bar: to enter the settings interface of the wireless router. According to the setup wizard step by step, select the Internet access method, and restart the wireless router after the setup is completed.

Next, go to the wireless settings and set the SSID name

1. The LAN port of the computer connected to the router;

2. Find out the default gateway of the router.

Start "->Run" and enter "cmd" -> "ipconfig", where default gateway is your router gateway.

3. Open the Internet Explorer browser and enter the gateway address of the router in the address bar. Go to the router and enter the username and password of the router.

4. After entering the page of the router, you can explore the settings by yourself. Generally, the router does not need to set it up by itself, and can automatically assign an IP address, the main thing is to enter and take a look, the SSID (network name) of the wireless network, and change the familiar wireless password by yourself.

The instructions are very clear, follow the instructions, and you can get it in a few minutes.

Please read the instruction manual Don't say you don't understand Chinese.

Prepare two network cables (the first one you have ready, which is the one that goes through the "modem").

The second is to buy a network cable sent by the router, if you don't send it, you have to make a network cable with crystal heads at both ends. ）

1.Change the local connection to automatically obtain the IP address.

2.The network cable from the "modem" (modem) is connected to the "wan" port on the router, and the router's ports 1, 2, 3, and 4 are connected to the network cable port behind the computer host.

3.Open the browser and enter the password and username of the router are admin

4.Go to the router settings screen, select the PPPoE (ADSL virtual dialing) method, enter your home account and password, and confirm.

5.Then set the SSID, encryption method, and password. Save, restart.

6.In the end, the setup is considered successful.

If your community is assigned an IP address, then yours is a static IP, and if you change it yourself, it will conflict with other people's homes; Generally, it is obtained dynamically, and if an IP is free, it will automatically assign you this IP.

You can connect the fiber directly to the computer without going through the router and ping the IP, and then connect to the router and set it according to the IP you ping.

If you use dial-up Internet access at home, choose PPPoE If you set the IP address, use a static IP address to access the Internet

Take out the manual, and teach you how to set it up step by step.

Home Network Environment Cabling:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Router Settings:

1. Check the router management address on the router shell label, there are two types of management addresses, please be sure to fill in the actual information. After entering the address in the browser, set the administrator password, and continue to set it (the default username and password of some routers is admin);

2. After entering the management interface, click Next to start the setup wizard, and select PPPoE (ADSL virtual dialing) in the Internet mode;

3. Enter the broadband account provided by the broadband operator in the Internet account and the broadband password in the Internet password;

4. Wireless settings: Set the wireless network name in the SSID, and set the wireless password of no less than 8 digits in the PSK password (it is recommended not to set the SSID to Chinese or special characters.) If the PSK password is set to 8 digits or more, be case-sensitive. ）；

5. Click Done, and the router is set up successfully. At this time, the computer that needs to access the Internet only needs to connect to the router LAN port or wireless network, and can access the Internet without any settings.

1. ** line access user (please prepare 2 short network cables): connect the ** line (the thinner line) to the line port of the cat (the smaller one), the cat separates a network cable to connect to the WAN port of the router, and then find a short network cable, one end is connected to the computer, and the other end is connected to the No. 3 interface of the router, and the wiring method is as follows:

2. Users who directly enter the home with network cables (please prepare 2 short network cables): directly connect the network cable to the WAN port of the router, and then find a short network cable, one end is connected to the computer, and the other end is connected to the No. 3 interface of the router, and the wiring method is as follows:

Use the page that opens in your browser to set the settings.

1.Connect your router.

Connect the broadband cable of the front-end Internet to the WAN port of the router, and confirm that the indicator of the corresponding interface is always on or flashing.

2.Log in to the management interface.

When the phone is connected to the router's wireless signal, the router's login page will automatically pop up. If it doesn't pop up automatically, open a mobile browser, clear the address bar and enter the router's management address or, the login page will be displayed, the login management interface, and the administrator password will be set.

3.Enter your broadband account number and password.

After logging in to the interface, please follow the wizard prompts to operate the router to automatically detect the Internet access mode and set the Internet access parameters4Set a wireless name and password.

On the wireless setting page, you can change the wireless name and wireless password of the signal and set the wireless parameters.

5.Complete the setup and reconnect your phone to the wireless signal.

At this point, the router setup is complete.

How to set up a TP-Link wireless router phone?

Line connection router and setup steps:

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

How to set up a TP-Link wireless router phone?

In general, it is connected to the wireless, enter it in the browser, and the account admin password admin can enter the management page, and configure the Internet access mode in it.

Open Internet Explorer (the software that surfs the Internet).

Enter the username admin

Enter the password admin

Enter the settings interface and set it according to your needs.

Enter :

Account and password: admin

There is a router address on the back of the TP-Link router, generally after making sure that there is no problem with the connection between the router and the network cable and the computer, open the IE browser and enter the router address.

When logging in to the router, you need to fill in the account and password of a router, and the initial account and password are admin

After entering the router, set your ADSL dial-up Internet account and password in the settings guide. Then follow the prompts to proceed to the next step and finally finish.

If there is no problem with the account and password for surfing the Internet, you can go directly to the Internet.

Enter the router.

Click Setup Wizard.

How to set up a wireless router.

Required tool material: TP-Link wireless router.

Here's how to do it (take TD-W89741N as an example):

1. One end of the network cable is connected to the WAN port of the router, and the other end is connected to the LAN port of the cat.

2. Open the browser, enter the IP address of the router), enter the router account and password (see the label or manual on the router box).

3. Point setting wizard.

4. Select the wireless ADSL route and click Next.

5. Check "Automatically detect PVC" (it can automatically detect the VPI and VCI values in the user's region), and then go next.

6. If the line is normal, the VPI VCI value of the current line can be successfully detected, and the next step is to do so.

7. Enter the broadband account number and password.

8. Wireless status: If you need to use the wireless function of the router, you must choose to turn it on, so that the host in the wireless network can access and access the wired network.

SSID Number: This item identifies the network name of the wireless network, which can be changed at will.

Channel: This option is used to select the frequency band (1-13) in which the wireless network operates.

Mode: This item is used to select the working mode of the router, which can be selected from 11M bandwidth mode, 54M bandwidth mode, 150M mode, G mixed mode and G N mixed mode.

Band bandwidth: Auto, 20MHz and 40MHz.

Maximum Sending Rate: Default is OK.

Once the setup is complete, click "Next".

9. Click Restart.