Do you need to break the wire to install LED car headlights?

Hello, if you replace the headlight assembly, you don't need to break the line, if it is modified on the basis of the original headlights alone, this needs to break the line, it is recommended to go to a professional modification shop.

If you install LED headlights, you don't need to break the wire, which needs to plug in the plug of the original model L E D lamp, if it is modified to LED, it is necessary to break the line, it is recommended to go to the auto repair shop for modification.

Hello, the installation of LED car headlight bulbs or the replacement of new headlight assemblies does not need to break the wire, because the LED car headlight bulb base and the original car base can be installed without damage. The plug can be directly docked with the original car plug.

Hello, for the car to install LED headlights, this does not need to break the wire, this only needs to be purchased according to the model, and then plugged directly into the plug, this does not need to be broken wire installation.

Hello, if it is to replace the LED headlight assembly, it needs to be modified by breaking the line. If you just replace the original car bulb with an LED bulb, you don't need to break the wire. It is recommended to go to a more professional place to replace and modify to avoid bad line connection.

Hello, buy LED bulbs directly, according to the original car bulb model purchase and installation does not need to break the wire, you can consult the accessories store, I hope it will help you, I wish you a happy trip.

Hello, if you just replace the LED headlight bulb is not required to change the original car line, you only need to replace the bulb can, if it is to modify the entire headlight, it may be necessary to change the line due to the different connectors.

Hello, the installation of LED car headlights all need to be installed with broken wires, because this is not the original accessory.

If you replace the assembly, you need to break the wire, if you don't need to change the assembly, of course, you don't need to break the wire, it depends on what you replace.

Hello, this LED headlight is installed without breaking the line, and it can be replaced directly.

If you install LED headlights, you need to break the line to replace the assembly, and if you don't need to break the line if you don't replace the assembly, please refer to it.

The LED headlights are installed non-destructively, and in most cases, they can be installed by directly replacing the original car bulb, which is simple and convenient. However, there are a small number of models on the market that do not take into account the problem of the owner modifying the lights when designing, so there are "unreasonable" places in the design, if the original car dust cover can not be covered, a special buckle is needed to fix the bulb, etc.

This specific need to see what kind of headlights you have, and some lights do not need to break the wire.

Hello, if this car is modified with headlights, this, you need to break the line, you can go to the 4S shop or repair shop to find out.

This belongs to the modification, it is necessary to move the main line, go to the auto parts city to change the lamp shop directly, the cost is relatively small.

It depends on what kind of car you are and how to install LED lights, and the best way for the rest is to go to a 4S shop or auto repair shop to find a professional master.

If you install LED car headlights, you need to break the line, and it is recommended that you go to your local car tuning shop for advice.

When the engine starts or does not start, the voltage of the circuit system is different, the former is about 14V, and the latter is about 12V. The voltage will also vary from car to car. Therefore, in addition to the lamp beads, there will be some electronic components on the qualified LED products, and the function of these components is to adjust the voltage so that the lamp beads can work stably under different voltages.

LEDs without voltage regulator components are often inferior products that control costs, and attention should be paid to screening when choosing.

1. Brand selection: We must choose a reliable big brand, and the risks of automobile lines must be taken seriously.

2. Model selection: It is best to choose a bulb with the same power as the original car, and must not choose a high-power bulb that does not match, as the circuit is overloaded and has potential safety hazards.

3. Installation attention: Some car bulbs can be installed directly, but some may need to change the wiring slightly, such as adding a diode or a resistor.

Select the installation site. Indoor and outdoor places with good ventilation, no corrosive gases, no combustibles and less dust are suitable for the installation of LED lights. The power supply voltage of LED lamps is rated in the range of +20% to -20%.

Wires should not be lengthened at will, especially those connected to the bulbs.

LED bulbs and ballasts are used together, and the electrical power should be the same, but the deviation is within the allowable range of about 10%.

For areas with cold winter or in outdoor places, the LED lamps used should be of high sealing level, and it is strictly forbidden to disassemble the cover of the lamps and lanterns.

Before installing LED lights, it is best to connect the lamps and lanterns first, and then install the lamps after powering on to confirm that the lamps will be on, so as to prevent the trouble caused by checking the lights after installation due to transportation or other reasons.

Before installation, when modifying the car LED light, you need to prepare some tools to connect the positive and negative poles of the bulb, what are the steps for the modification of the car LED light? The resistors need to be connected, and one end of the positive electrode is cut. The use of the welding torch directly to the position of the positive electrode requires resistance welding, and these need to be prepared, and only after these preparations are in place before the retrofit, then it will be more convenient and there will be no errors.

Operators and disadvantages: Modify the positive and negative electrodes to weld the positive and negative electrodes below the resistor, and also need to find the right direction, what are the steps for the modification of automotive LED lights? White wire is used to weld in the direction of the resistance. In addition, heat shrink tubing is used to drop it from under it to one end of the wire.

This is pushed all the way to the underside of the bulb. The tool is tightened with a tool on the wires of the positive and negative poles, and it can be done. Therefore, when operating, it is necessary to check each step according to the above steps, and each step needs to be checked when it is complete, so as not to have an impact.

Different styles of cars have different operating methods when modifying, and there will be some differences in the materials that can be used, so there are also adjustments in operation. Retrofitting and inspectionAfter the connection is made, it also needs to be inspected. What are the steps for car LED light modification by using clips to clamp LED bulbs?

When it is operated, it is very safe. Welding two wires next to each other increases its firmness. It will also be more convenient to use.

Therefore, it needs to be tested after the connection, and if it can be used normally, then the effect is also ideal, so that when it is used, it can bring more convenience to people. Tell the potato.

Recently, I plan to modify the car headlights, what do I need to pay attention to when modifying the car headlights with LED lights?

1. Pay attention to whether the illumination angle of the car headlights when modifying the LED meets the requirements, the irradiation angle will affect the driver's field of vision, and will also affect the phenomenon of concentrating.

2. Pay attention to the wattage of LED modified by car headlights, too low wattage will cause its brightness to not reach more than 1400 lumens stipulated by the state, which is not only easy to cause traffic accidents, affect driving safety, but also can not successfully pass the annual inspection of the car.

3. Note the quality of the modified LED of the car headlights, do not choose the poor quality LED lights, not only the use time is short and the failure rate is high, but also its color temperature, color gamut and heat dissipation and other functions are also poor, sometimes even unable to meet the daily needs of the owner.

4. It is also necessary to pay attention to whether the car itself can be compatible with LED headlights, most models are possible, if not, it can be solved by installing a decoder and other methods. It is also necessary to check for phenomena such as astigmatism, and if necessary, to improve the light gathering ability of modified LED headlights.

To modify the car LED lens from the original car base, the lights need to be turned on and resealed, and the level of repositioning and decoding needs to be adjusted.

Owners who want to modify the LED lens headlights of the car must find a professional car modification service organization to upgrade and modify the lights to ensure the illumination effect and quality of the lamps after the modified LED lenses.

Heat dissipation is also the main problem of modified LED headlights, because the original headlights were designed at the beginning of the replacement of LED bulbs, so the heat concentrated on the lamp body is usually difficult to dissipate, so LED heat dissipation needs special attention, the life of the bulb is also difficult to guarantee, the original car is equipped with LED headlights and upgraded LED bifocal lenses can be used with confidence.

Modding tips

Due to the moderate LED lights, good light effect and high brightness, many car owners hope to convert the original halogen lights into LED lens headlights, but to modify the LED lens to slow the lights, you need to pay attention to the problem and ensure the quality after modification.

If the original car directly replaces the bulb of the LED light source, it will cause serious light scattering and dazzling problems of the car lamp, and the astigmatism and high beam will seriously affect the vision of the vehicle driver. After using a vehicle with a replaced LED bulb, due to the use of the original headlight reflex grip bowl, even if the low beam is turned on, without the help of the LED bifocal lens, the strong light emitted by the LED bulb will produce a strong scattering, which is not friendly to other drivers, and may even lead to safety accidents in serious cases.

Of course, the LED taillights can be repaired. Automotive LED taillights are innovative brake lights and taillights that use long-term LED light sources. When a car brakes, makes a U-turn, or makes a U-turn, they can send signals to other vehicles and pedestrians.

The automotive LED taillights have excellent light source intensity, which can maintain excellent visibility even in foggy days.

LED has the obvious characteristics of long life, high light efficiency, no radiation, and low power consumption. Theoretically, its service life can be as long as 100,000 hours, but after being made into a car light, the general service life is 20,000 hours, that is, if you turn it on 24 hours a day, the LED can be used for about 800 days. Of course, no one will have their headlights on 24 hours a day.

LED lights are brighter, more energy-efficient, prettier, and of course more expensive.

Over the years, low-profile streamlined styling has become increasingly popular due to design, aerodynamics, and aesthetic needs. The shape of the tail lights is also developing towards special-shaped and integrated. Depending on the application, automotive LED lights can be divided into two types:

Distribution lights and decorative lights. The light distribution light is suitable for the backlight display of instrument indicators, front and rear turn signals, brake indicators, reversing lights, fog lights, and reading lights. Decorative lights are mainly used to change the color of the lights and beautify the interior and exterior of the car.

Millions of car purchase subsidies.

Car LED taillights can be repaired. Automotive LED taillights are innovative brake lights and taillights that use long-term LED light sources to signal other vehicles and pedestrians when the car brakes, makes a U-turn, or turns. Automotive LED taillights have excellent light source intensity and maintain high visibility even in foggy days.

LED is an electroluminescent device that uses a solid semiconductor chip as a light-emitting material and emits light directly through photon emission caused by carrier recombination. LED headlamps are lighting devices that are manufactured using LEDs as a light source.

Headlights can be used not only in automobiles, but also in displays, traffic lights, LCD backlights and lighting, with a wide range of applications.

LED has the remarkable characteristics of long life, high light efficiency, no radiation and low power consumption. Theoretically, its service life can be as long as 100,000 hours, but after being made into a car light, the general service life is 20,000 hours. That is to say, if it is turned on for 24 hours, the LED can be used for about 800 days.

Of course, no one will have their headlights on 24 hours a day. LED lights are brighter, more energy-efficient, prettier, and of course more expensive.

In recent years, low-profile streamlined styling has become increasingly popular due to design, aerodynamics, and aesthetic needs. The shape of the tail lights is also developing towards special-shaped and integrated. Automobile LED lights can be divided into two types: distribution lights and decorative lights according to their uses.

The light distribution light is suitable for instrument indicators, front and rear turn signals, brake indicators, reversing lights, fog lights, reading light backlight display, etc. Decorative lights are mainly used to change the color of the lights and beautify the interior and exterior of the car. Millions of car purchase subsidies.

Headlight modification should choose a regular modification factory to ensure the safety of modification. 2.The modification personnel should adjust the original design and circuit of the vehicle in accordance with the original design of the vehicle, try to keep the original state of the vehicle, minimize the adjustment and modification, and avoid damage to the original circuit of the vehicle.

3.Use regular brand LED lamps and lanterns to ensure safety and reliability.

4.Conduct adequate inspections prior to installation of vehicle headlights to ensure that the fixtures and circuitry are installed correctly.

5.After the installation is completed, joint commissioning should be carried out to ensure that the performance of the headlights is normal and reliable.

Millions of car purchase subsidies.