How do you change a spare tire for a car? How to change the spare tire of the car

1. Park the car with a flat tire on the right, take out the warning sign from the car, and place it about 100-150 meters away from the back of the car.

2. Then take out the tire change kit from the car, with spare tires, jacks, wrenches, etc., and prepare to change tires.

3. Use a jack to lift the side of the puncture tire first, and remember to top it on the steel beam or the girder under the chassis.

4. Then use a special wrench for tire disassembly and assembly to unscrew all the screws on the hub.

5. After unscrewing the screws, pull the tire out vigorously and take out the entire broken tire.

8. Find a place to repair tires as soon as possible, check the specific situation of broken tires, and either repair or change tires, because there are not many roads to drive for spare tires.

8. Find a place to repair tires as soon as possible, check the specific situation of broken tires, and either repair or change tires, because there are not many roads to drive for spare tires.

8. Find a place to repair tires as soon as possible, check the specific situation of broken tires, and either repair or change tires, because there are not many roads to drive for spare tires.

Take out the hand jack, spare tire and sleeve, put the jack on the lower beam of the vehicle, shake the jack, use the sleeve to loosen the tire screws after slightly resisting (the strength is limited, you can use the pedal sleeve rod to operate), after completing the above operations, shake the jack again until the tire is off the ground, completely unscrew the screws and remove the broken tire and replace it with the spare tire, and finally fix the tire with one hand to the maximum extent and tighten the screw with the sleeve with the other hand, put down the jack, and tighten the screw again by pedaling the sleeve rod.

Quick and easy way to change the spare tire Can't remember** at the end.

1. Put a heavy object (such as a stone, concrete brick, spare tire, etc.) in front of the front and rear tires.

2. Take out the spare tire and jack, place the jack under the frame close to the tire you want to replace, and make sure the jack touches the metal part of the frame.

3. Raise the jack until it supports (not lift) the car, the jack should be firmly under the vehicle, check and make sure that the jack is at right angles to the ground.

4. Remove the hub cover and loosen the nut in a counterclockwise direction. Never loosen the nut completely, as long as it's enough to remove the drag, and when you first loosen the nut, keeping the tire on the ground will ensure that you're turning the nut and not the tire.

5. Twitch or turn the jack to lift the tire off the ground, and you need to lift it to a height high enough to remove the flat tire and replace it with a spare tire.

6. Loosen all the nuts completely, turn the nuts in a counterclockwise direction until they are loose, repeat this step for all the claw nuts, and remove the nuts completely.

7. Remove the tires and put the flat tires under the vehicle, then if the 11,000 pounds fail, the vehicle will also fall on the old tires, and the car can be avoided by this method.

8. Put the spare tire on the hub, carefully align the spare tire rim with the wheel bolts, and then install the wheel claw nuts.

9. Tighten the nuts by hand until all nuts are tightened.

10. Lower the car and remove the jack so that the spare tire can be replaced.

Changing the spare tire of the car requires a method and requires the driver to have certain skills.

When changing the spare tire of the vehicle, park the car in a safe and stable area first, turn on the double flashing lights, and place the tripod; Remove spare tires and special tools; Remove the plastic bottle cap on the top of the anchor bolts; Use a socket wrench to loosen the anchor bolt in the opposite direction and at the top angle; support on the hydraulic jack; remove the tires ; Install a spare tire; Tighten the screws to the level where the tire is fixed; learn to put down a hydraulic jack; Finally, the highest force application of special tools to tighten the screws; Replace the spare tire.

1. Park the car in a reliable area, turn on the double flashing lights, place the tripod 150 meters away from the car, and only come to the car after prompting, pay attention to avoidance.

2. First of all, take out the spare tire and special tools, first use the thin wire hook to take out the plastic bottle cap on the five anchor bolts of the tire, pull out the hook as soon as it comes out, and then use the socket wrench to loosen the anchor bolts in the opposite direction at the top angle, and loosen them one by one to replace one. Because the screws of the spare tire will be tightened very tightly, if necessary, you must use your foot to loosen the screws.

3. Then put the hydraulic jack on the vehicle, pay special attention to the lifting place to be stuck, and the crankshaft can be used to rotate the hydraulic jack to lift the car, and lift the tire to completely leave the road. Then remove the tires.

4. After replacing the spare tire, you can put on the screws, and you must also use the top angle of the driving screw, tighten it one by one and replace it with one by one, and screw it to the level that can fix the spare tire, without thorough tightening.

5. Learn to put down the hydraulic jack and tighten the screws with the highest force screws of your hand with special tools.

To better ensure safety, it is possible to stuff a tire into the chassis when removing the spare tire to reduce damage. It is also necessary to choose a flat and firm one, so it is recommended that everyone tuck another tire under the vehicle before lifting, so that in case of an accident, this tire can also be blocked to reduce damage.

After the object is retrieved, put it in its original position, put the removed tires and tire special tools in the original part of the trunk of the car, and don't forget to take the warning triangle behind the hip of the car home. As an emergency tire, the spare tire is subject to a speed limit.

There are usually 50 or 80 colorful words written on the spare tire, which means that the speed should not exceed 80 kilometers (50 miles per hour) after the spare tire is replaced. Since the spare tire itself is used as an emergency application, its effect is to enable the vehicle to survive to the repair shop for repair, so it cannot replace the original tire for long-term use.

Drive off the main road, pull over, turn on the vehicle warning lights, pull up the handbrake, and do the following.

1.Open the trunk, find the red cuboid box, open the box and take out the warning triangle, and place it fifty meters behind the car.

2.Take out the hand jack, spare tire and sleeve, put the jack on the lower beam of the vehicle, shake the jack, use the sleeve to loosen the tire screws after slightly resisting (the strength is limited, you can use the pedal sleeve rod to operate), after completing the above operations, shake the jack again until the tire is off the ground, completely unscrew the screws and remove the broken tire and replace it with the spare tire, and finally fix the tire with one hand to the maximum extent and tighten the screw with the sleeve with the other hand, put down the jack, and tighten the screw again by pedaling the sleeve rod.

Quick and easy way to change the spare tire Can't remember** at the end.

If we have a flat tire during driving, or the tire is out of gas, the car will not drive right, the driving will become slow, if the front wheel will be difficult to control the direction, at this time must not continue to drive, should immediately get out of the car to check, park the car first, turn on the danger lights, put the warning triangle.

First of all, we have to see if the spare tire of the car is good, and if it is good, we must start replacing the spare tire.

Take out the tools and jacks that come with the car first, usually these things are in the trunk and the spare tire together or on both sides of the spare tire.

First, use the tire wrench in the vehicle tool to loosen the screws of the bursting tire, otherwise it will not be loosened after jacking.

See 1 image remaining.

Then use a jack to jack up the side of the punctured tire, which can top the hard place on the edge of the bottom of the car.

See the remaining 2 images.

Then use a wrench to remove the tire screws, you can take the tire down, some tires will stick to the hub, so it will be tighter, you can kick the edge of the tire twice, and take the tire off after sending.

See 1 image remaining.

Then take out the spare tire, put the spare tire on the tire screw, be sure to align the screw, otherwise the screw can not be installed, and then screw the tire screws all by hand, and tighten it slightly with a wrench.

See 1 image remaining.

Then let go of the jack and tighten the tire screws with a wrench, which can be tightened according to the strength of the dismantling to ensure that the tire screws are all tightened.

Then put the tires and tools and jacks well, everything is done, you can continue to drive, you must take the burst tires to the maintenance place to deal with, if it is out of gas, you can see if it is a nail, if you have a nail, you can repair it, if it bursts, you need to replace the tire.

Precautions. Be sure to tighten it when installing.

Before driving, check that the tools, jacks, and spare tires must be normal.

2.Take out the spare tire and tools, and use a wrench to loosen all the screws in a diagonal direction in a counterclockwise direction. Find a load-bearing beam on the site and jack it up until the tire is off the ground;

3.Remove all the screws and remove the tire, put it at the bottom of the car to prevent the jack from slipping, align the screws and install the spare tire, and install the diagonal square.

1. Tools for taking out the trunk, including: wire hook and loop (for pulling out the bolt cover), jack, wheel wrench.

2. Put the wrench on the bolt, turn it to the left, and press it with your foot if necessary.

3. Find the support point of the car jack (located in the position of the girder inside the concave point at the bottom of the vehicle), adjust and shake the car jack until the car wheels just leave the ground. At the same time, place the spare tire on the left side of the jack at the bottom of the vehicle (to prevent accidents and damage to the vehicle).

4. Completely screw out the bolts one by one, remove the wheel, replace the spare tire, and tighten all the wheel bolts (no need to tighten). Place the replaced wheels on the left side of the jack (to prevent accidents and damage to the vehicle).

5. Rotate the car jack to put down the car and tighten the wheel bolts with a wheel wrench. Do not tighten the bolts sequentially, but in a diagonal pattern alternately and step by step, placing the jack and the replaced wheels into the trunk.

1.If you are changing a tire on the side of the road, be sure to use the vehicle's tripod to place it 150 meters behind the car. Warn the oncoming car behind to ensure your own safety.

2.Spare tires are not full-size compared to original tires, so we should go to the repair shop in time to repair the tires and replace them with the original tires after replacing the spare tires. The spare tire should not be used for a long time and can only be used as a temporary backup.

It is best not to exceed the speed of 50 yards during the driving of the spare tire.

3.The tire set screws have been removed, but it may be difficult for the tires to be removed because of the heavy dead weight of some tires. At this time, you might as well be bold and kick the tire, and it will come down automatically.

Although the replacement of vehicle tires is relatively rare in daily life, it is not afraid of 10,000 in case, if you go out or outdoors, once a tire failure occurs, it can be much more convenient to do it yourself. Waiting for help is not only time-consuming but also costly. Secondly, in the daily maintenance process, we must regularly check the tires in the trunk, and open the trunk spare tire compartment before traveling to check whether the spare tire is normal and whether the replacement tools are complete.

Take out the hand jack, spare tire and sleeve, put the jack on the lower beam of the vehicle, shake the jack, use the sleeve to loosen the tire screws after slightly resisting (the strength is limited, you can use the pedal sleeve rod to operate), after completing the above operations, shake the jack again until the tire is off the ground, completely unscrew the screws and remove the broken tire and replace it with the spare tire, and finally fix the tire with one hand to the maximum extent and tighten the screw with the sleeve with the other hand, put down the jack, and tighten the screw again by pedaling the sleeve rod.

Quick and easy way to change the spare tire Can't remember** at the end.

Quick and easy way to change the spare tire Can't remember** at the end.