What is a car called a traceless dent repair?

The dent repair is based on the principles of optics, physics and mechanics, and the use of the lever principle will be affected by various external reasons in the vehicle, and the different sizes and depths of the depression appear on the car body, provided that the body paint surface is not damaged, and the metal surface is not excessively stretched, which is a modern process. Automobile dent repair technology is an international advanced technology for the repair of various parts of the car appearance, due to the impact of external forces to form various depressions for repair, the technology also greatly shortens the repair time (a depression repair takes about 20---40 minutes), and greatly reduces the cost (only about 50% of the traditional sheet metal and painting). And the concave part repaired by this technology will never deform and fade, completely make the vehicle show its original style again, whether it is the door cover, front wing, rear compartment cover, etc"Pits", the repair range is more than 90%.

Automobile dent repair technology uses a variety of technical means such as strong magnetism, strong bonding, and optical lever to decompose, micro-repair, pull and flatten the car depression part point by point, and restore the car depression without moving the original car paint. The force of the tool acts directly on the back steel plate of the concave paint surface of the body, so as not to destroy the paint of the car, so as to achieve the effect of no painting.

The most direct and traditional method is to use thermal expansion and contraction, directly splash hot water to heat the injured and dented parts of the car, and then press them with your hands or with a pry bar to push out the dent little by little to achieve the effect of repair.

2. The same is the use of the principle of thermal expansion and contraction, you can choose to use the hair dryer to heat, so that the efficiency is higher, at this time, you can cooperate with two people, while heating, while squeezing, speed up the repair of the car time, if the car depression is relatively large, you can appropriately increase the number and temperature of the hair dryer, increase the heat transfer, and then, press internally to help recovery.

Traceless repair is actually micro sheet metal, the principle is actually very simple, is based on optics, mechanics, the use of lever principle from the inside of the pits of different depths to slowly restore to the original appearance, the repair effect depends on the master's technical level, if the technology is strong, there is no problem from the front, for the individual the benefit is that the traceless repair does not need to destroy the original car paint. Hope, thank you!

The traceless repair of the vehicle and the dent repair of the car belong to the same meaning, without damaging the paint of the vehicle to restore the appearance of the vehicle to its original state, especially for the collision of the pits, and hail craters have a very obvious effect, the use of professional tools pure manual repair.

Car dent repair ** bright time.

The invention was made in 1946, the place of invention was in the United States, and the time it came to China in 1999 was the related technology imported from South Korea, and the Korean technology was imported from Japan. Car dent repair is very different from traditional sheet metal repair. The paint can be repaired without damage, and there will be no traces at all.

How car dent repair is charged.

Fees are based on the area and location of the specific restoration. The larger the area, the more complex the location, and the higher the charge**. Although the ** of dent repair will be higher than that of traditional sheet metal repair, the benefits to the vehicle are also very good, and there will be no depreciation problem after the vehicle **.

Hello, car dent repair is to repair the dent part of the car paint to its original state. Under normal circumstances, the original state of automobile depression repair can be achieved by acute and obtuse angle depressions. The main thing is that the depression without paint can be repaired as before, the hail pit can be repaired, and the corners and AB pillars are not easy to repair.

Sheet metal repair is to repair the deformed part of the metal shell of the car, such as the body shell is hit by a pit, you can restore it to its original state through sheet metal, and then through spraying special paint, the deformed metal surface of the car can be restored to the same as other intact places, as bright as ever.

Automobile dent repair is different from traditional sheet metal painting, and the charging standard is not charged by face, but according to the size and location of the car dent repair.

However, many car owners encounter door dents and think about doing sheet metal repairs. In fact, it is not that serious, if the car paint is not damaged, we can try to repair it ourselves, there are many car dent repair tool sets on the Internet, and the tools inside are basically complete,

The technology of repairing car dents without traces is a very hot technology in the market now, because this technology is worthy of everyone's trust.

If there is a depression in the body or surface of the car, it is necessary to repair it, mainly through the repair of the automobile sheet metal, this process requires the repair process such as sheet metal scraping and polishing, which can not be completed by itself under normal circumstances, and must be carried out in a professional auto repair shop or 4S shop.

The so-called automobile dent repair technology, also known as micro sheet metal, also known as traceless and non-destructive technology, etc., does not need to destroy the original car paint.

The car can retain the original car paint to the greatest extent possible, which is relatively high.

Body dents without paint can be repaired without a trace.

Compared with sheet metal painting, the dent without trace repair technology can repair the car depression while retaining the original car paint, which solves the problem of many car owners who love the original car paint.

However, the indentation without trace repair technology is very powerful, but there are also restrictions on its use, such as the paint on the sunken part has not been damaged and has not been repaired. In addition, if the depression is very close to the edge of the body sheet metal, or if the rear fender of some cars is a double-layer design, it is not suitable for non-marking repair.

Precautions for the repair of non-marking depressions:

After a scraping accident occurs in a vehicle, you should immediately choose a more suitable place to park. After parking, tighten the hand brake, cut off the power supply, and turn off the engine of the car. In specific cases, the regulations of specific circumstances should be observed, such as wide lights and tail lights should be displayed at night.

On highways, hazard warning signs should also be set up behind the car according to regulations.

Check the condition of your vehicle. It is appropriate to use digital tools to record the situation on the spot. For example, the camera function of the mobile phone and the digital camera carried with you can record the scratch parts and the condition of the car.

Usually, it is necessary to shoot the front side of the car, the rear side of the car, and the bump parts from multiple angles. It is best to have a shot in the footage that reflects that both parties are at the scene.

For paint-free car dent repair, we may have a misunderstanding, here I popularize science, the so-called car dent repair technology is also known as micro sheet metal, we sometimes call it traceless non-destructive technology, etc., anyway, there is no need to destroy the original car paint for body concave repair, the principle is actually very simple, that is, based on optics and mechanics, the use of the lever principle to slowly restore the different depths of the pits to the original appearance (similar to the factory reset of mobile phones), look at the following picture you can see at a glance.

Everyone thinks that this technology is very simple, it is really easy to enter the industry, it is really difficult to really do a good job, the market is still in a downturn in the country, many people do not understand this technology, and there are many people who rely on the gourd to draw a scoop, coupled with the early closed repair, so that the industry is very limited, the car depression repair technician who is really called a master master, is one of the few in the country, after all, each master has different requirements for himself, and the repair effect is good and bad. It is not a matter of time before what is really repaired is the same as the original paint, it is experience and understanding. Therefore, when you repair, you must choose a well-known local car dent repair shop, small shop, backpacker, and really repair the general.

The prospect of learning car traceless repair technology is still good, because now the sheet metal paint is strictly checked, so the car traceless repair technology conforms to the development of the environmental protection situation, and now many private cars are very valuable, the body appears a small depression, and they are generally unwilling to paint, so the car traceless repair technology will become a demand in the automobile service market, but at present, China's car maintenance masters who can fully master this technology are really few, and even there is a situation where supply exceeds demand. Therefore, it is still very good to learn the technique of repairing the dent of the body without leaving a trace.

Automobile traceless repair technology belongs to a profitable technical project, because you only need to bless the tuition fee of learning technology and the cost of purchasing a set of tools, and the repair cost of the later renewal process is basically zero, so the technology is very profitable. I'm worried that I can't make any money. However, Huang Pineapple suggests that if you run your own store, you can also master the windshield repair technology by the way, which can increase the strength of your store and increase your income.

It depends on how easy it is to live. Usually the sheet metal will be sprayed again, and the two are generally counted together. For general grade cars, the door is an example, and the small sheet metal and painting fee is about 400 yuan.

Traceless repair is actually micro sheet metal, the principle is actually very simple, is based on optics, mechanics, the use of lever principle from the inside of the pits of different depths to slowly restore to the original appearance, the repair effect depends on the master's technical level, if the technology is strong, there is no problem from the front, for the individual the benefit is that the traceless repair does not need to destroy the original car paint. Hope to adopt, thank you!

1. Go to the repair shop to practice a lot, but you should choose a good repair shop with a big business to learn faster, the best master will take the initiative to teach you how to repair, why do you want to repair it like this, although the shop often works overtime, but it takes more time to do it alone, and it learns quickly, so it is very important to find a good repair shop and master, so it depends on luck.

2. If you want to learn, you can actually go to the training school to sign up for a short-term class to learn faster, this kind of learning can be started directly, and you don't need to be an apprentice in the repair shop to slowly boil, whether it is to find a job or start a business and open a shop, it will be faster and more convenient.

This belongs to the sheet metal project of car beauty, like our side has a separate project of learning, a professional team of teachers and facilities and equipment, you can get started quickly, you can consult and understand. With the gradual increase of motor vehicles, especially private cars, an auto beauty maintenance industry known as the "best industry" has made more and more people pay attention to it. At present, the booming auto market will surely drive the rapid development of the auto beauty service industry, and the auto beauty industry has become an industry with considerable investment value.

Automobile non-marking dent repair is an international advanced technology for repairing various parts of the automobile appearance due to the impact of external forces. This technology also greatly shortens the repair time, a depression repair takes about 20 to 40 minutes, and greatly reduces the cost, only about 50% of the traditional sheet metal, painting, and the repair of the depression will never be deformed and faded.

Advantages of car scar-free dent repairAutomobile dent repair technology adopts professional technology and fast process to retain the original appearance of the car paint, so as to maintain and reflect the original value of the car, and the repair time is short: the car dent repair technology takes about 15 to 90 minutes to repair a pit, and the construction is convenient.

Automobile non-trace dent repair is an international advanced technology for repairing various parts of the appearance of the car due to the impact of external forces and various dents in front of the front of the shape. This technology also greatly shortens the repair time, a depression repair takes about 20 to 40 minutes, and greatly reduces the cost, only about 50% of the traditional sheet metal clearing, spray paint, and the depression repaired by this technology will never be deformed and faded.

Advantages of car scar-free dent repairAutomobile dent repair technology adopts the process and fast process of the special Maoling industry, retains the original appearance of the car paint, so as to maintain and reflect the original value of the car, and the repair time is short: the car dent repair technology takes about 15 to 90 minutes to repair a pit, and the construction is convenient, and the car dent repair technology mainly uses special customized maintenance tools for construction operations, and can be operated in any place and place under the condition of carrying a mobile power supply or meeting the power supply.

However, many car owners encounter door dents and think about doing sheet metal repairs. In fact, it is not that serious, if the car paint is not damaged, we can try to repair the wheel Ling Qingfu by ourselves, there are many car dent repair tool sets on the Internet, and the tools in it are basically complete, such as suction cups, hot melt glue guns, etc. However, remember to be cautious when repairing it, otherwise the depression may become prominent.

In practice, it is still difficult to repair this kind of depression, because if the depression is too small, then the effect is difficult to reflect, unless the area is large and the depression part is relatively gentle.