Why is the hammer beating weak, and the sound is wrong

There are many reasons why the breaker does not sound, such as the hammer has no strength, the nitrogen pressure is not enough, and the oil pressure of the pipeline is not enough. In addition, it is also related to the local weather at that time and the hard pre-opening of the ore. When the breaker does not sound, it can be dealt with like this:

At an early age, first check whether the pressure of nitrogen is enough; Check whether the static oil pressure is enough;

The reason why the breaker does not go off after an hour or two is that it is sealed or stuck.

The hydraulic breaker adopts the optimal design concept, increases the stroke of the piston and the cylinder block, and adopts the same large diameter of the piston and the drill rod, so that the crushing hammer and the host have the best matching effect, rationally use the highest output energy, save energy, and achieve the highest work efficiency.

The force will be slightly greater in the case of a single blow, and it will not be reflected in the case of continuous blows. The leather bowl in the accumulator will cause damage to the leather bowl if the nitrogen is small, and it is troublesome to need the overall dissection during maintenance.

Hello! I'm Maike Hydraulic Breaker Company.

1. Too much nitrogen, because the nature of nitrogen is hot expansion and cold contraction, after 2 hours, the temperature of the 2 oil seals can not achieve the sealing effect, and the rigid body enters the hydraulic oil.

3. Piston diarrhea.

There is also a problem with the main rammer of the excavator.

The problem is a lot of nitrogen, oil seals, and it's possible that the control valve is stuck with something, and there's a lot of possibilities, and it's possible that little details can make your machine not move, but every time, does it get stuck after two hours? How long have you been repairing your machine?

Is it a month? Or is it useless to leave it for a long time?

The excavator uses No. 68 hydraulic oil, the crushing hammer may be the oil seal is broken after the rigid body is oiled, the symptom is that the excavator can hit 0000 when the machine is cold, and the blow is slow when the machine is warmed

The most awesome and best fault to solve is that the middle of the tubing is peeled, and I have encountered it twice.

There are many reasons for the lack of sound, it may be an air seal, or it may be the card owner, which should be considered in many ways.

It may be that the nitrogen seal is not good, the nitrogen pressure is insufficient, and it is good to fill it with nitrogen.

<> pro

Hello, I am happy to answer for you, the possible reasons why the breaker does not sound are as follows: 1Hydraulic cavity system failure:

The breaker needs a power wheel to make it work, and the hydraulic system is an important part of providing power. If there is a fault in the hydraulic system, such as an oil leak or insufficient pressure, it can cause the breaker to not work properly. 2.

Hammer damage: If the hammer head of the breaker is damaged or worn excessively, the contact area of the hammer head with other parts will be reduced, resulting in insufficient striking force, which will affect the generation of noise and vibration. 3.

Asymmetrical striking area: The breaker needs to maintain the uniformity of the striking area when working, if the striking area is skewed or asymmetrical, it may cause the sound of the breaker to be too low or not loud when working. 4.

The gap between the breaker and the object: the breaker needs to maintain a certain gap with the broken object when working, if the gap is too large or too small, it may cause the breaker to not work properly.

Summary. 1.The hammer design is unreasonable <>

A hammer head that is too small or poorly designed will result in insufficient hammering force to produce sufficient sound. 2.Hammer handle quality problem:

If the hammer handle is not of good quality, it is easy to break or deform, and the hammer force and sound are reduced. 3.The gap between the hammer and the nail is too large

If there is a gap between the head of the breaker and the object being nailed, it will cause energy to be lost <>

The reason why the breaker does not sound when it is pressed against it.

1.The hammer design is unreasonable <>

A hammer head that is too small or poorly designed will result in insufficient hammering force to produce sufficient sound. 2.Hammer handle quality problem:

If the hammer handle is not of good quality, it is easy to break or deform, and reduce the hammering force and sound. 3.The gap between the hammer and the nail is too large:

If there is a gap between the head of the breaker and the object that was scattered before it was nailed, it will cause <> energy to be lost

The above is the reason why the breaker does not sound tightly.

Pro, the original town of the crushing hammer against the original town is not beaten because of the following reasons: 1Hydraulic system failure:

The working principle of the breaker is to rely on the hydraulic oil pressure provided by the hydraulic system to drive its work, if the hydraulic system is faulty, the breaker will not work normally. 2.Blocked oil circuits:

Blockage of the oil circuit means that the oil cannot flow normally, which may be caused by the fouling, rust and other substances generated inside the pipeline, resulting in the oil not flowing smoothly, so that the breaker cannot work normally. 3.Electrical Fault:

The breaker needs to rely on the electronic control system to control its working state when working, and if the electronic control system is faulty, the breaker cannot work normally, and this fault usually needs to be repaired by professional maintenance personnel. 4.Improper setting of working parameters:

If the working parameters of the breaker are set improperly, such as the unreasonable setting of strike frequency and strike intensity, it will also cause the breaker to fail to work normally, and the setting parameters need to be adjusted. In short, there may be many reasons why the breaker does not sound tightly, and it is necessary to judge and analyze it in combination with the specific situation.

Hello dear, glad to give you an answer for the stool. A breaker is a tool with a special structure, and its hammer head is made up of several parts that can be separated and reassembled. During use, if a part of the hammer head is loose or falls off, it will not move, but as long as it is re-tightened or reassembled, it can continue to be used.

In addition, the breaker is elastic to reduce vibration and recoil forces, thus extending the service life of the hammer. Therefore, the breaker can be beaten again after a while, probably due to its special structure and elastic properties.