The water purifier shows that there is no water in the pressure barrel all the time, what is the mat

The water inlet solenoid valve is out of order, and the check valve is out of order. Judgment method: turn off the power supply and pressure barrel ball valve, if the wastewater stops, it means that the check valve is out of order, open the pressure barrel ball valve and there is wastewater outflow, you can confirm the problem of the check valve, and the check valve needs to be replaced; Turn off the power supply and pressure barrel ball valve, if the wastewater does not stop, it means that the water inlet solenoid valve is out of order, and the water purification solenoid valve needs to be replaced.

It may be that the high-voltage switch is out of order or the set pressure of the high-voltage switch is too high, resulting in the pressure of the pressure barrel not reaching the set pressure of the high-pressure switch.

1. The high-pressure pump of the water purifier does not start, and the water cannot be made to check whether there is a power outage and whether the plug is plugged in; Check whether the low-voltage switch is out of order and cannot be connected to the power supply; Check whether the high-voltage switch or water level controller is out of order; Check transformers, fuses.

Whether it burns or not. 2. The high-pressure pump of the water purifier works normally but cannot make water, and the high-pressure pump loses pressure; The pre-filter element is clogged (no pure water wastewater or small wastewater); Check valve blockage (there is wastewater, no pure water); The solenoid valve fails and cannot be opened effectively; RO membrane.

Whether it is clogged or not. 3. The high-pressure pump of the water purifier does not stop, and the pressure of the high-pressure pump is insufficient, and the set pressure cannot be reached; The check valve is blocked, and the high-pressure switch fails to produce pure water (there is waste water but no pure water), and it cannot jump; The solenoid valve fails and cannot be opened effectively; 4. The high-pressure pump of the water purifier is shut down, but the wastewater does not stop, and the solenoid valve fails, and the water cannot be effectively cut off; Inspection Method:

Close the ball valve of the pressure barrel, if there is still wastewater, it can be concluded that the solenoid valve is out of order); There is also a situation, close the water inlet solenoid valve and then open, if the machine is normal, then it is judged that the water pressure is too high, resulting in the solenoid valve can not be closed flexibly, then consider adjusting the water inlet to reduce the water pressure); Check valve pressure relief, (waste water is very small) (inspection method: close the inlet solenoid valve, if there is still wastewater, it can be concluded that the check valve is pressure relief). 5. After the water purifier is full, the raw water pressure of the machine repeatedly jumps is insufficient; Check valve pressure relief; high-voltage switch failure; There is pressure relief in the system.

6. The pressure barrel of the water purifier is full of water, but the clean water cannot flow out of the pressure barrel to relieve pressure; Post-activated carbon.

Jam; Whether the pressure barrel ball valve is damaged. 7. The water purification flow of the water purifier is insufficient, and the pre-filter element is blocked; Insufficient pressure of the high-pressure pump; RO membrane blockage; The wastewater ratio is out of balance or the flushing switch is not closed tightly. 8. The ratio of water purification to waste water of the water purifier is seriously out of balance, and check whether the flushing solenoid valve is damaged; Check if the wastewater proportioner is clogged or too conductive; Check for blockage of the RO membrane or a severe decrease in the removal rate.

9. The machine keeps flushing the wastewater than it fails or the flushing beginning is not tight. 10. Check the water path of the water purifier for water purifier leakage and find the water leakage point; Check whether the small Unicom is leaking; Check the water dispenser for leaks; If the water leak is very small and not easy to check, it can be used for dry facial tissue testing.

Hello dear and happy to answer for you. The water purifier shows that there is no water in the water pressure barrel all the time, and the reason for the bending and seepage is as follows: 1

The high-pressure pump of the water purifier does not start, and it cannot make water Check whether there is a power failure and whether the plug is plugged in properly; Check whether the low-voltage switch is out of order, and cannot be connected to the power supply; Check whether the high-voltage switch or water level controller is out of order; Check whether the transformer and fuse are burned. 2.The high-pressure pump of the water purifier works normally but cannot make water, and the high-pressure pump loses pressure; The pre-filter element is blocked (there is no pure water and wastewater, or the wastewater is small); Check valve blockage (there is wastewater, no pure water); The solenoid valve fails and cannot be opened effectively; Whether the RO membrane is clogged or not.

3.The high-pressure pump of the water purifier does not stop The pressure of the high-pressure pump is insufficient and cannot reach the set pressure; The check valve is blocked, and the high-pressure switch fails to produce pure water (there is waste water but no pure water), and it cannot jump; The solenoid valve is out of order, can not be effectively opened, kiss exclusion of these three methods can be solved, I hope to help kiss you, I wish you all the best, and I hope that kiss can give a thumb<>s up

The pressure barrel of the water purifier is a key component, and its main role is to provide pressure in the water purifier system to push the water through the filter. If there is no water in the pressure barrel of the water purifier, it may be caused by the following reasons:

Insufficient water pressure: The water purifier pressure barrel needs a certain water pressure to operate, and if the water pressure is insufficient, there will be no water in the pressure barrel. Check that the water pressure in your home is normal. If the water pressure is too low, you can associate with your water utility and have them check and fix the problem.

Clogged pressure drums: If the tubing in your water purifier system becomes clogged, it can cause no water in the pressure drum. You can check if there is a blockage in the inlet and outlet pipes of the water purifier, and if there is a blockage, you can use the appropriate tools to remove it.

Problems inside the pressure bucket: If there is a problem inside the pressure bucket, it can cause water to not be able to enter the pressure bucket. For example, an air bag inside a pressure drum can leak or burst, making it impossible for water to enter. In this case, the pressure drum or the airbag need to be replaced.

Water purifier failure: If the above problems do not solve the problem of no water in the pressure barrel, then it may be that the water purifier itself is faulty. At this time, you need to contact a professional water purifier maintenance personnel for maintenance and repair.

If there is no water in the pressure barrel of the water purifier, you need to first check whether the water pressure is normal and whether there are problems such as blocked pipe covers. If none of these issues resolve the issue, then the pressure bucket or other parts of the water purifier may need to be replaced or repaired. In any case, it is recommended that you seek professional help to solve the problem and ensure that your water purifier can function properly.

1: First confirm that the power supply is normally energized (it is recommended to use other electrical appliances to plug in the plug for direct drinking water to burn whether it is energized). 2：

Open the faucet whether there is a fine flow of water (if there is water) 3: Whether the ball valve on the pressure barrel is open (if it is not opened, please open, the angle of the valve is consistent with the water pipe) 4: Close the ball valve of the pressure barrel and the valve of the direct drinking water faucet.

Whether the whole machine is shut down. 5: If everything is normal, please put the pressure barrel ball valve in the open position, adjust or replace the high pressure switch.

Use an Allen socket screwdriver for the debugging process, and refer to Part 4 for adjusting the clearance.

If there is no water flowing out of the 2nd test, and the 1st power supply is normal, the fault should be the transformer or Piyuanye motor, which needs to be replaced.

If you can't understand the above, go directly to the after-sales service provider.

If it is a solenoid valve, check the size of the water flow of the waste pipe, if the water flow is large, replace the solenoid valve, if it is a manual valve, please put it in the closed position, and the waste pipe will still have a small waste water discharge.

Check whether the line mountain round pipe is connected correctly and check whether it is energized. If it's an old barrel, then it may be that there is no rough only force, and there will be an air valve under the barrel that is the same as that of a bicycle.

The pressure barrel of the water purifier has no pressure, check whether there is any leakage inside the pressure barrel, check whether the valve of the pressure barrel is damaged, clean the filter of the water purifier, and clean the pipe of the water purifier.

The pressure barrel of the water purifier can be operated without pressure and can be operated as follows:

1. Check whether there is water leakage inside the pressure barrel: if there is water leakage, the pressure barrel needs to be repaired or replaced.

2. Check whether the valve of the pressure barrel is damaged: if the valve is damaged, you need to replace the valve.

3. Clean the filter of the water purifier: If the filter is clogged, you need to clean the filter with a suitable tool.

4. Clean the pipes of the shed disturbance water purifier: If the pipes are blocked, you need to clean the pipes with appropriate tools.

The pressure barrel of the water purifier can be divided into 3 types according to the material, plastic pressure barrel, stainless steel pressure barrel, and plastic clad steel pressure barrel.

1. The plastic pressure barrel has good elasticity, and it rarely breaks when used. The disadvantage is that the pressure of this product is relatively small, and the water yield may not be very large.

2. The stainless steel pressure barrel is made of carbon steel, which can withstand a lot of pressure, and generally large products will be paired with stainless steel products.

3. The pressure-bearing capacity of the plastic-clad steel pressure barrel is strong, and the plastic used externally has good elasticity and is not easy to fail. But its tomb will be improved compared to the first two types of pressure barrels. <>

If the newly bought water purifier keeps showing the water pressure and there is no water in the bucket, then it may be the following situations, you can read it carefully. 1. The high-pressure pump cannot produce water without starting.

Second, the high-pressure pump works normally but cannot produce water.

3. The high-pressure pump does not stop.

Fourth, the high-pressure pump is shut down but the wastewater does not stop.

5. The pressure bucket is full of water but pure water cannot flow out.

6. Insufficient flow of pure water.

1. Water purifier, also known as water purifier and water purifier, is a water treatment equipment that carries out deep filtration and purification treatment of water quality according to the requirements of water use. The water purifier that we usually talk about generally refers to a small purifier used for home use.

2. The core of its technology is the filter membrane in the filter element device, and the main technology is ultrafiltration membrane and RO reverse osmosis membrane. The water purifier can effectively filter out rust, sand and gravel, colloids in the water, and adsorb residual chlorine, smell, discoloration, pesticides and other chemicals in the water.

3. It can effectively remove bacteria, germs, toxins, heavy metals and other impurities in water. The application of water purification technology in the field of drinking water makes the phenomenon of "water and soil adaptation" quickly become a thing of the past, and effectively solves the endemic diseases caused by excessive harmful substances in groundwater in many places.

The water purifier pressure barrel does not produce water may be the following:

1. The internal accessories of the water purifier are blocked or ineffective, or other internal accessories are damaged.

2. The filter element or permeable membrane dust failure.

3. Water pipe problems.

4. The booster pump is faulty.

The recommended workaround is as follows:

1. The internal accessories of the water purifier are blocked or ineffective, or other internal accessories are damaged.

Solution: After half a year of use, it is best to check and maintain the internal accessories of the machine every 2-3 months, which can be responsible for the health of drinking water, and can extend the service life of the machine and internal parts, while ensuring the water output and quality of the product.

2. The filter element or permeable membrane is faulty.

Solution: Since the filter element or permeable membrane has restrictions on use, it is best to clean the product every 1-2 months after use, remove the pollutants and blockages inside the filter element or permeable membrane, ensure that the product is clean, and avoid problems such as low water volume and water deterioration.

3. Water pipe problems.

Solution: If the water pipe is damaged, directly cut off the damaged place, if the damage is too large, directly replace a new water pipe. If the water pipe is blocked, use tools and clean water to open the inside, and if there is too much accumulation to get through, just replace it with a new one. Repentance.

4. The booster pump is faulty.

Solution: Look at where the booster pump has a problem, the booster is the core working hardware, it is best to repair, if it cannot be repaired, it is recommended to replace.

Hello dear, I'm glad for your question, the water purifier shows that there is no water in the water pressure barrel all the time, what's going on? The water inlet solenoid valve is out of order, and the check valve is out of order. Judgment method:

Turn off the power supply and the pressure barrel ball valve, if the wastewater stops, it means that the check valve is out of order, open the pressure barrel ball valve and there is waste water flowing out, you can confirm the problem of the check valve, and the check valve needs to be replaced; Turn off the power supply and pressure barrel ball valve, if the wastewater does not stop, it means that the water solenoid valve of the inlet shed is out of order, and the water purification solenoid valve needs to be replaced. It may be that the high-voltage switch fails or the set pressure of the high-voltage switch is too high, resulting in the pressure of the pressure barrel not reaching the set pressure of the high-voltage switch.

Dear, I will find out for you: the water purifier shows that there is no water in the pressure barrel of the water production stopper, and the reason is that the water inlet solenoid valve is out of order, and the check valve is out of order. Judgment method:

Turn off the power supply and the pressure barrel ball valve, if the wastewater stops, it means that the check valve is out of order, open the pressure barrel ball valve and there is waste water flowing out, you can confirm the problem of the check valve, and the check valve needs to be replaced; Turn off the power supply and pressure barrel ball valve, if the wastewater does not stop, it means that the water inlet solenoid valve is out of order, and the water purification solenoid valve needs to be replaced. It may be that the high and simple person thinks that the pressure switch is out of order or the set pressure of the high-voltage switch is too high, resulting in the pressure of the pressure barrel not reaching the set pressure of the high-voltage switch.

Summary. Generally speaking, there are two possibilities for the water purifier, one may be that the pressure barrel valve of the water purifier is closed, because there is no water storage space, the water purifier will show that the water is full after working for a short time, and the other possibility is caused by the damage of the high-voltage switch in the water purifier, and there are very few cases that are caused by damage to the motherboard.

Water purifier, the indicator light only shows that the water is full, not water, but there is no water in the pressure barrel, what is the reason.

Generally speaking, there are two possibilities for the water purifier to appear in this kind of situation, one may be that the pressure barrel valve of the water purifier is closed, because there is no water storage space, the water purifier will show that the water is full for a short time, and the other possibility is caused by the damage of the high-voltage switch in the water purification machine, and there are very few cases that are caused by damage to the motherboard.