What should I do if the CAD shortcut key is not available?

1. In this case, we only need to click "Tools" in the menu bar, and then click "Options" in the drop-down menu.

<>3. As shown in the figure, check "Double click" and "Use shortcut menu in the drawing area", which should solve the problem that the shortcut key cannot be used. Let's click on "Custom Right-Click" and go in and set it up.

Shortcut command invalidity refers to the situation where AutoCAD shortcut command cannot be used, but the full name command can be used. For example, take the CAD2010 I use as an example, we commonly use the move, copy command, generally enter the simplified command m, co can call the corresponding command, the antivirus software accidentally deletes the file and causes it to fail, the CAD prompts the invalid command, and the full name of the command such as move and copy can be used.

Workarounds for all shortcut keys in CAD that are out of order:

1.Introduction to shortcut command failures:

I used the powerful mode of the 360CAD virus killing tool to kill the virus after the ***lsp virus was detected in the CAD, as shown in the figure below.

More than 400 ***lsp suspected virus files were detected, and I was on fire at the time, and I deleted them all completely without looking at them, which shows my hatred for this kind of CAD virus! o o It's not the first time I've been poisoned! Having said so much nonsense, I want to warn everyone not to blindly trust antivirus software, and to be a little careful, otherwise it will be a mess

Next, I am ready to continue drawing, and as a result, I enter M to modify the drawing, and a warning sign appears in CAD, saying that it is an unrecognized command, but the full name of the move command can be used.

2.The perfect solution:

At this time, you must find your original CAD installation file, and if you don't have it, go to ** yourself. Double-click to open it, and unzip and install it in your CAD installation directory, for example, it was originally installed in D: AutoCAD2010, and now you also select D:

AutoCAD 2010, at this point it will automatically overwrite the file, and the files you are missing or deleted by mistake will be available. (I'm too lazy to take a screenshot, I believe I understand).

Then open the control panel and reinstall the CAD.

Click to go to the following screen and select "Repair or Reinstall(R)".

Next, select "Reinstall AutoCAD 2010(e)", click Next, and wait.

Install it and you're done. Generally, there is no need to restart, and the shortcut command can be called after the reinstallation is completed, so far it is perfectly solved!

1. In this case, we only need to click "Tools" in the menu bar, and then click "Options" in the drop-down menu.

<> can't use the question. Let's click on "Custom Right-Click" and go in and set it up.

Maybe the source is that the shortcut to write the block has been changed, so you can't use it. In the tool - Tonglun self-determined lead Xinyi - program parameters, here is a look at the modification.

If the system is caused by an error in the system settings, the specific solution steps are as follows: The first step is to enter the command of redefine in the interface of the CAD software, as shown in the following figure.

The second step is to press the Enter key on the blind keyboard to confirm, and the redefine command will appear in the status bar, as shown in the figure below. Step 3: Move to the icon of the insert block in the left tool, as shown in the figure below. Fourth, the insert command appears in the status bar, as shown in the figure below.

Step 5: Enter insert, as shown in the figure below.

What should I do if I don't use the CAD shortcut? The specific steps to solve the problem are as follows: Step 1:

Enter the redefinition command in the CAD software interface, as shown in the figure below; Step 2: Press the Enter key on the keyboard to confirm, and the input redefinition command will appear in the status bar, as shown below; Step 3: Move to the left sail side tool or shed insert block icon, as shown below.

Step 4: The Insert command appears in the status bar as shown in the image below. Step 5:

Enter the insertion, as shown below.

Some basic shortcuts of AutoCAD can't be used, and I want to regret that the fix has failed. Start by typing in the command "op".

2. Enter the command "op" to open the "Options" menu, and find the "User System Settings" option in the previous column of the options menu. For specific locations of operation,