What should I do if the disc is spent? What to do if the disc is scratched

The disc took the processing method:

1. The simplest and easiest way is to take a piece of suede or soft paper.

2. After breathing on the CD, wipe it in a clockwise direction without force for a while (do not wipe it clockwise and counterclockwise).

3. Then it's best to make a backup.

Use alcohol or take it to the computer market to see if it can be read or fixed, first determine if there is a problem with your disk or your optical drive.

There is also if the information is very important, go to the place where the disc is repaired, about 150-300 yuan 1g like this**.

Tell you! In any case, don't put toothpaste on the CD, it will ruin your CD and find it all the time circulating on the Internet"Method:", I tried it myself, not only can't even fix the scratch, but it will make your disc not look good! (Just think about it, toothpaste contains it.)"Abrasives"--- smeared that sand-like thing on the disc and also"Friction"??

In addition, wipe the disc from the inside out, and never wipe it in a circle along the disc.

The landlord can use a bad disk copy tool like badcopy to copy your plate again! Burn a new disc!

The easiest and easiest way is to take a piece of suede or soft paper, puff it on the CD and rub it in a clockwise direction for a while (do not wipe it clockwise and counterclockwise), and then make a copy of it.

How to get a scratched disc back.

There are two main ways to get a scratched disc back

1. Wash with soap. This method is suitable for less severe discs.

2. With professional repair, the plastic on the plate can be polished. Note that this effect will not be noticeable when burning discs.

How to fix scratched discs.

Use a soft cleaning cloth dipped in toothpaste and a little sewing machine oil, polish the scratched surface of the disc a little hard to the outer ring, and polish the severely scratched areas several times, then wash and dry (not in the sun!). You will find that the effect is much better!

Disc scratched Is there any way to do it?

1. Find a new *** optical drive to read the disk. 2. Dead horses should be live horse doctors!! Use a little toothpaste (*** a little) to smear the scratches, and then gently wipe them with deerskin (preferably) or silk cloth, until the scratch marks are light, wipe off the toothpaste, dry it, and try again!

It is advisable to use the first method first. The second is to use it as a last resort!

I have a disc that has been scratched and the rest of the content can't be put out? Can it be fixed?

Yes, but it's more expensive to repair it than to buy one, under the Microsoft official website.

Disc scratch How to fix disc scratch.

Repair Discs: Generally speaking, discs cannot be repaired if they are deeply scratched or badly damaged. If it is only slightly scratched or scratched, or it cannot be read due to poor quality, etc., in this case, you can take the disc to a newer recorder to read, and if you can read it, copy and burn a copy to solve the problem.

CD! What should I do if I get scratched?

Minor scratches can be repaired with a CD repair solution, and when the disc is readable, the CD content is transferred to the computer for saving, because the damaged disc may crash at any time, resulting in unrecoverable information. If the scratch reaches the substrate, there is no way to return to the sky.

It is recommended to strengthen the protection of optical discs at ordinary times, and you can buy a special touch disc protective case or disc storage bag, so that you can avoid disc scratches.

1.Put it in the computer CD-ROM drive, copy it, and burn it to another CD; 、

2.I've seen a method in a book before, first of all, I haven't tried it before, that is, apply toothpaste to the scratched part of the disc, and then cut the toilet paper or cloth (preferably the kind of delicate cloth) to wipe the disc, or you can wipe it directly to achieve the purpose of removing the scratches, so that you can read.

3.The last way is to go to a specialty store to repair it, there are special tools that can flatten your disc, I hope it will help you.

What to do if the system disc is scratched.

Take a look to see if it's scratched, and if you can't use it, find another one.

My game disc is scratched, genuine! It's very distressing, everyone begs you to tell me what to do! No toothpaste or anything! 70 points.

If you can still use it, you can't use it, but it doesn't look good, then it should be used as a second-hand one, and then buy a new one.

Dear, I've been waiting for a long time! <>

If your video disc is spent, you can try to fix it using some simple calendar lighting methods. First of all, you can use some professional disc repair tools, such as a disc repair machine or disc repair fluid, etc. These tools can help you remove scratches and stains from the surface of your disc and bring it back to normal use.

Second, you can try to use some common household methods, such as using toothpaste or banana peels, to clean the surface of the disc. Although these methods are not as effective as professional tools, they can also repair discs to some extent. Finally, if none of the above methods solve the problem, you can consider buying a new disc to replace it.

In conclusion, repairing a video disc requires attention to using professional tools or common methods at home, while keeping the surface of the disc clean and smooth, in order to repair the disc effectively.

Changing the optical drive is not the best way, the scratched disc will also damage the laser head, the wedding disc is a very important thing, take it to the place where the disc is sold, let them help you take the disc to polish it, it's OK, but I suggest that you take it back, copy it with the computer, and store it with a U disk, so that it can be better preserved, I hope to adopt, thank you.

Butterfly pieces can't be released in the Shadow Butterfly Machine.

It's that the butterflies can't be released, and the butterflies stop reading for a long time.

It is a butterfly of Kamiju.

Asking questions is not a shadow butterfly machine, and everything else can be released.

Question: If you don't have a card, you can't put it out, it's a bit of a show.

The usual method is to apply toothpaste and water to the data surface of the CD, and then use your fingers to repeatedly apply the toothpaste evenly on the data surface of the CD in a clockwise direction, and the scratches on the CD are smoothed out by this method.

But there are still some discs that are still very poor, the data surface of these discs has basically not seen scratches, but why is it so hard to read, but these discs have a similarity, that is, when the disc is laid flat, and then look at it from the side, it is found that the disc is not very flat, it is estimated that the disc is uneven and causes the optical drive to be unable to read well, the current optical drive speed is very fast, and the optical drive also has very high requirements for the geometric regularity of the disc. When rotating at high speed, as long as the disc is a little irregular, it will float up and down under the drive of the optical drive spindle motor, which makes it difficult for the laser head to align the disc and adjust the focal length.

1. Wipe and repair with disc repair solution; 2. Change to a better CD-ROM drive to read.

Is it scratched or bent?

The question is bent and deformed.

The question was not carried.

Answer: It can be sandwiched between two thick pieces of glass, clamped with iron clamps around it, and then placed in hot water 65 75. Soak for 10-15 minutes and then remove to cool while continuing to pressurize for 1 to 2 hours. Finally, it can be removed from the glass room and dried to restore its original shape, and the water temperature can also be a little higher.

Try it kissing.

Ask a questionOkay, I'll give it a try.

Since I didn't know how to break it by hand, it was a little broken, the blisters were fine, and the broken ones were glued with 502.

Answer kiss, can't [tear run], the data is broken when it is broken, and it is useless to stick it [tear run] to ask the reading surface is not broken, but there is a crack on the back. Isn't this okay, and the answer is that only the back is broken, and it should be okay.

Kiss you and try it, the naked eye can see that the reading surface is not broken, but I don't know if he can ask a question inside, thank you! Very satisfied, can you stick with 502.

1. CD disc is mainly divided into five layers, the substrate is made of polycarbonate material injection molding, in which there is a substrate layer, a recording layer, a reflection layer, a protective layer, and a printing layer (there are words on this side, there are disc identification, capacity, name, etc.). The data is stored in the recording layer and is read out under the reflection of the reflection layer. The recording and reflective layers of a disc are protected by a protective layer and a printing layer on top and a substrate layer below, so that the disc can be durable.

2. From the picture, the printing layer of this disc is contaminated, not a scratch, it looks unsightly, and it does not affect the use. If you are afraid of affecting future use, you can use the recorder to make a copy, or copy it to the hard disk for later use.

There is no solution ... The tracks are all damaged.

First of all, you have the necessary recovery software, and you can try several data recovery software, maybe one of them can recover more data. Of course, I recommend CD Recovery Toolbox here.

Put your damaged platter in the optical drive, and the software will be able to list the contents of the files and folders found in the platter, and then select the data you want to recover, which is a very slow process that you have to be able to live with.

Another piece of software is Roadkil's Unstoppable Copier, which is also a similar recovery software, but it can pause and save the recovery progress for the next time you can resume it.

If it's Linux, you can try ddrescue, and here's what command line might use:

Try repairing the damaged platter.

If you have deep scratches on your platter, you can also fix it. The best way is to use a white toothpaste or a polish (preferably on an optical instrument), but also brasso.

Start by using a soft cloth to wipe the surface of the disc, and if there is any greasy stains, you can use a mild detergent to clean it. Make sure the surface of the plate is free of finger marks or other contaminants. Do not use too much force when cleaning to avoid injury.

Use toothpaste or gloss to apply to the damaged part of the surface of the platter, try to control the amount at the beginning to prevent too much contamination to other parts, and then gently wipe it from the center to the outside with a soft cloth.

Of course, not all platters can be recovered, and sometimes it is not uncommon for some platters to recover only part of the data.