How to install colored lights on motorcycles, how to disassemble motorcycle lights

Tools Materials: a number of colored lanterns, a number of cable ties, a plum blossom driver, a square driver, double-sided tape.

One roll, gasket.

Scissors, a utility knife, and a roll of electric tape.

The steps are as follows: 1. Remove the original headlights with a plum blossom driver before starting the installation.

2. Disassemble the back cover.

3. Remove the bulb and lampholder.

4. LED headlights are worn from the back to the front.

5. Put the gasket on the answer.

6. Tighten the heat dissipation screws.

7. Cover the mask and the installation is complete.

In fact, changing the lights will make the motorcycle very beautiful and eye-catching at night, but don't do too much, you can't see the modification of the bulb is the most nb, you can add chassis lights, license plate lights, front and rear tile cover lights, engine lights, these lights are invisible, you can only see the light reflected out, especially good-looking, ** on the sale, very cheap, I hope your car is very beautiful!!

There is a wire package at the socket connection of the headlight, open the wire pack, take out the wire connected to the headlight socket, and connect the +-pole and -pole respectively to the +-pole of your colored light. You can also try to connect the line of the lantern to the line of the headlight switch, so that your headlight switch can control the headlight and the lantern you have changed at the same time! Hehe!

The headlight switch is on the front of the car, you open the hood, and you will see the wires wrapped together, you just need to connect your color car directly to it.

Turn on the handlebar switch, the same as the ordinary lamp head line, positive to positive, negative to negative, don't connect directly to the switch, connect to the line of the headlight, wrap it with black tape, and don't touch the line.

The lap of the chassis looks beautiful at night, and my brother installed it like this.

How to install the steel basin cutting lamp?

Prepare the material: a screwdriver.

<>4. Remove the shell on the lamp, and then unscrew the screws on the lamp.

5. Finally, remove the lights.

It is the kind of headlight that is glued to the lampshade, to disassemble the headlamp glass, you need to use a hair dryer to heat the headlamp, bake the glue soft and slowly pry it open with a decoration blade and a flathead screwdriver, do not bake only one place for a long time, the temperature is not too high, avoid the lampshade deformed, pay attention to the strength when prying, so as not to pry the lampshade.

Typing is not easy, such as satisfaction, hope.

Tools Materials: a number of lanterns, a number of cable ties, a plum blossom driver, a square driver, a roll of double-sided tape, a gasket, scissors, a utility knife, and a roll of electric tape.

The steps are as follows: 1. Remove the original headlights with a plum blossom driver before starting the installation.

2. Disassemble the back cover.

3. Remove the bulb and lamp holder.

4. LED headlights are worn from the back to the front.

5. Put the gasket on the answer.

6. Tighten the heat dissipation screws on the stove.

7. Cover the mask and the installation is complete.

Tools Materials:

1. A number of colored lanterns.

2. A number of cable ties.

3. One plum blossom screwdriver and one square screwdriver.

4. One roll of double-sided tape.

5. a gasket. 6. A pair of scissors and utility knives.

7. A roll of electric tape.

Steps to install lanterns:

1. Remove the original headlights with a plum blossom driver before starting installation.

2. Kyungji unpacks the back cover.

3. Remove the bulb Yanzhou and the lampholder.

4. LED headlights are worn from the back to the front.

5. Put on the gasket.

6. Tighten the heat dissipation screws.

7. Cover the mask and the installation is complete.

Summary. There are some basic steps in the installation of the license plate light for the bottom of the motorcycle lamp. First of all, you need to prepare the appropriate bottom plate light assembly, which usually includes a bulb, a lampshade, and a fixing bracket.

The premise is that you have a complete understanding of your motorcycle's electrical system and have obtained the correct installation location of the bottom license plate light as well as an understanding of the possible legal requirements. Second, you'll need to power off your motorcycle and find the right place to install the bottom license plate light assembly. Some motorcycles may already have a reserved installation spot, or you may need to design your own.

Next, you'll need to insert the bulb into the lampshade and attach the mounting bracket to the shade. Finally, install the bottom plate light assembly to the previously found location and secure it. Remember to follow the safe operating practices when performing the above steps to ensure that all circuits are connected correctly and that relevant regulatory requirements are followed.

There are some basic steps in the installation of the license plate light for the bottom of the motorcycle lamp. First of all, you need to prepare the appropriate bottom plate light assembly, which usually includes a bulb, a lampshade, and a fixing bracket. The premise is that you have a complete understanding of your motorcycle's electrical system and have obtained the correct installation location of the bottom license plate light as well as an understanding of the possible legal requirements.

Second, you'll need to power off your motorcycle and find the right place to install the bottom license plate light assembly. Some motorcycles may already have a smiling shirt mount on it, or you may need to design your own. Next, you'll need to insert the bulb into the lampshade and attach the mounting bracket to the shade.

Finally, install the bottom plate light assembly to the previously found location and secure it. Remember to follow the safe operating practices when performing the above steps to ensure that all circuits are connected correctly and that the relevant regulatory requirements are followed.

Excuse me, but please go into more detail?

The installation steps of the motorcycle bottom license plate light include: preparing the lamp assembly, turning off the power supply shed, finding the installation location, connecting the bulb and the lampshade, fixing and installing the lamp assembly. Make sure you understand the circuit system and regulatory requirements and follow the safe operating specifications.

<> dear, hello, I will answer this question for you, how to install the scooter big Nian calendar light bulb The solution to your problem is as follows: the headlight bulb of the scooter is very easy to install, but to remove the headlight, you need to remove the front cover of the handlebar or the front panel shell of the silver search, after the fixing screw of the plastic plate, pry open the clip of the plastic part as the case may be, remove the front panel or handlebar front cover, and pull out the rubber behind the headlight, so that you can directly remove the original bulb, Then just install the new bulb as it is, some of the bulbs are installed with twisting, some are pressed, and it is very easy.

Summary. Hello, the installation method in front of the off-road lamp is as follows: first remove the motorcycle headlight, then install the xenon bulb in the appropriate lamphead card, and then install the bulb into the light box.

Find a suitable place to fix the ballast. Connect all the plugs well, the red SE wire is connected to the positive pole of the battery, and the HEI wire is connected to the negative pole of the battery. Connect the huang wire and blue wire to the handle switch for the far and near lights.

How to install the front of the motocross lights.

Hello, the installation method of this side of the off-road lamp is as follows: first remove the motorcycle headlight shirt hail, then put the xenon bulb in the appropriate lamp head card, and then put the bulb into the light box. Find a suitable place to fix the ballast.

Connect all the plugs to He Xun, the wire of the red SE is connected to the positive pole of the battery, and the HEI wire is connected to the negative pole of the battery. Connect the huang wire and blue wire to the handle switch for the far and near lights. <>

Extended information: The motocross bike has a simple structure, easy to maintain, and the power xing is suitable for civilians and amateur off-road enthusiasts. This kind of vehicle has a strong sense of fun, as long as the driving hall accompanies the driver to dress up and play stupid, you can ride it over the mountains, climb the slopes and wade through the water. <>

1. The steps of women's motorcycles are: open the seat and use a plum blossom driver to disassemble the plastic cover plate on the fuel tank under the seat.

For men's motorcycles, remove the side plastic buckles, and for curved beam motorcycles, open the seat and use a torx driver to remove the plastic cover from the fuel tank under the seat.

2. Find the tail brake light terminal, the brake light has three wires, two of which will be on after turning on the car lights, and will become brighter after braking, we have to find the two small light lines.

3. After connecting it, leave enough wires to the outside, install the lanterns and light strips to the position you want to install, 4. Connect the reserved wires with the lanterns, glue the light strips with double-sided tape, and then tighten them with cable ties and cut off the excess parts of the cable ties.

5. Turn on the headlights and turn them on.

It's good if you don't compromise on safety.

Multiple places can. See what effect you want.