How to install the motorcycle throttle cable, how to adjust the motorcycle throttle cable?

The steps to install the motorcycle throttle cable are as follows:

1. Pass the throttle cable through the carburetor first.

Put the cover, then put the spring on the throttle line, and then extend the throttle cable through the throttle valve (the tube you said) hole, pull it out of the groove next to it and go around to the bottom, and release the head of the throttle cable into the Mekong groove at the bottom of the throttle valve.

2. When loading the throttle valve into the carburetor, pay attention to the small slope of the throttle valve.

Over there towards idling.

Screw, drop a long groove towards the side of the carburetor with a raised point in the carburetor, and then tighten the cap, and you can see the throttle valve falling to the bottom from the throat of the carburetor.

3. Open the lid of the plunger, and then pass the throttle wire through the middle of the spring of the plunger cover.

4. Pass the plunger hole of the throttle line, and then lock and fix it with screws to complete the installation.

It is necessary to remove the upper cover of the carburetor, take out the return spring and throttle valve of the throttle valve, pass the throttle line through the groove and spring on the throttle valve, fix the solder joint of the head of the throttle line in the groove at the bottom of the throttle valve, and load the throttle valve into the carburetor according to the angle (pay attention to the positioning pin, otherwise the throttle valve will not fall to the bottom), and then install the upper cover of the carburetor.

Mu has a way to explain to you, the culture is low and the words are poor, so there is no way to describe it. The sound is particularly loud, indicating that you are stuck on the accelerator. The carburetor bucket was raised.

Find a motorcycle repair master to give you a little money. You can watch it from the side. That's how I learned.

If it fails, it is not installed, and the medicine looks like that kind of car, and there are many kinds of carburetors, and the throttle line is different.

1、First, start the engine, adjust the clearance and tightness of the throttle handlebar, and then accelerate the test drive.

2. If you feel that the throttle handle is heavy (as if something is pulling), it means that there is interference in the throttle pull wire, and there will be a rustling sound when pulling, which is mostly caused by the pull wire winding around the handlebar. At this time, you can use a screwdriver to loosen the cable fixing screws to see if the noise can be eliminated.

3. If the cable is damaged, there will be a "click" sound during operation, and it is best to replace it with a new cable.

1. First of all, check whether the throttle cable has signs of looseness, or the refueling is not smooth, and the idle range is large. The throttle line adjustment nut should be under the handlebar, it is used to adjust the throttle clearance, and when adjusting, turn the adjustment nut counterclockwise or clockwise to adjust the size of the throttle clearance, and then check whether the acceleration is smooth and without lag.

2. If the throttle line is deformed or the use time becomes longer under the condition that it cannot be adjusted, or there is no change after adjustment, it should be replaced.

3. You can refer to the "User Manual" of the car for adjustment.

What I'm trying to say is how to install the throttle cable with the accelerator bar? It's mainly with an acceleration bar, and when you lift it a little, you can still say what he was like, and the line will be pulled to whatever position.

Summary. Dear, I am glad to answer for you, the motorcycle throttle cord installation method is to pass the throttle cord through the upper cover of the carburetor, put the dan spring on the throttle line, and then pass the throttle cable through the throttle hole, and pull it out from the slot next to it to the bottom; Load the throttle valve into the carburetor; Open the plunger cover and pass the throttle through the middle of the plunger cover dan spring; Pass through the plunger hole of the throttle line and lock it with screws to complete the installation.

The method of installing the motorcycle throttle cord is to pass the throttle cord through the upper cover of the carburetor, put the dan spring on the throttle line, and then pass the throttle cord through the throttle hole, and pull it out from the groove next to it to the bottom; Load the throttle valve into the carburetor; Open the plunger cover and pass the throttle through the middle of the plunger cover dan spring; Pass through the plunger hole of the throttle pipeline, lock it with screws, and complete the installation.

Motorcycles are light and flexible, fast, widely used in patrols, passenger and cargo transportation, etc., motorcycles are divided into street cars, road racing motorcycles, off-road motorcycles, cruising vehicles, station wagons. A motorcycle is a nimble and fast tool with an internal combustion engine. The motorcycle was the world's first motorcycle invented by the German Daimler.

The installation method of the motorcycle throttle cable is: 1. Pass the oil world positive and scattered door line through the upper cover of the carburetor, put the spring on the throttle line, and then extend the throttle line from the throttle valve hole, pull it out from the groove next to it until it goes around to the bottom, and release the head of the throttle line into the groove at the bottom of the throttle valve; 2. When the throttle valve is installed in the carburetor, pay attention to the small bevel of the throttle valve facing the idle screw, and the long groove towards the raised point in the carburetor and fall to the bottom, and then tighten the cover. The two lines of the motorcycle are leading to the throttle handle on the right side of the handlebar, the top is the throttle search line, which is responsible for controlling the throttle valve and the oil needle, and the next to the clear seepage is the accelerator pump line, which can make the carburetor spray a stream of oil to the throat when the throttle is tightened sharply, so as to improve the acceleration during rapid acceleration.

What is the installation method of the motorcycle throttle line The installation method of the motorcycle throttle cable is: 1. Pass the throttle line through the upper cover of the carburetor, put the elastic spring on the throttle line, and then extend the throttle line from the throttle valve hole, pull it out from the groove next to it and go around to the bottom; 2. Install the throttle valve into the carburetor; 3. Open the lid of the plunger and pass the throttle line through the middle of the spring of the plunger cover; 4. Pass the plunger hole of the oil key to remove the trouser door line, lock it with screws, and complete the installation. Motorcycles are two-wheeled or three-wheeled vehicles powered by gasoline engines and steered by handlebars, which are lightweight, flexible, and fast, and are widely used for patrolling, passenger and cargo transportation, and are also used as sports equipment.