How to install the shower rail holder

Taking a bath every day may be a habit for most people, or the subway market can keep everyone healthy. Then for each of us, there should be a good shower at home.

Right? We all know that a good shower must be inseparable from a good holder. Only if the shower can be installed better, we will be able to rinse more easily.

So in order to let you choose a better shower holder, the next will give you a detailed introduction to the details of the shower holder.

How to install the shower holder - the type of shower holder

Portable shower stand: Portable shower is the most commonly used shower, and portable shower holder only has the function of fixing the shower, commonly known as the base.

Overhead shower bracket: Overhead shower is commonly known as large shower, the bracket is installed in the wall, does not have a lifting function, the water outlet angle of the shower can be adjusted, and the upper and lower movement angles are more flexible.

Lifting shower bracket: This kind of shower bracket is usually used for large showers, which has the effect of lifting the height of the shower, and the height of the shower can be adjusted according to the height of the user.

How to install the shower holder - the installation method and steps of the shower holder

1. Install two shower mounts. The shower mount is recommended one off the ground.

The height is meters, and the other is meters. Start by inserting the decorative cup into the threads of the shower bracket. Wrap the raw meal tape.

After that, screw the left and right shower brackets into the hot and cold water pipes respectively.

joints. 2. Adjust the distance between the front end of the left and right shower brackets to 9 cm, and the height is the same, and the distance from the wall is the same. Place the water-stopping gasket.

Put it in the faucet. The water inlet hole at the rear of the body, then install the shower faucet on the shower bracket. Install the spout.

The installation environment of the shower rod holder The outlet joint of the hot and cold water pipe is a universal caliber of 1 2 inches, preferably a tapered threaded joint of R1 2, with hot water on the left and cold water on the right; The distance between the center of the joint is about 15 cm, and the height of the joint from the ground is recommended to be 60 cm.

3. Install the shower pipe and shower head. Take a look at some small commodity wholesale markets, there are special.

**Concept Household Items.

of merchants, there is a special suck.

in the tiles. On the product can be placed in the shower.

After installation, the faucet must be horizontal and not tilted, about 900-1100mm from the ground, and use a wrench.

When installing the faucet, be careful not to damage the plating surface.

The above is to introduce to you the details of the shower holder, I believe you have a certain understanding of the shower holder after you see the introduction! The shower holder is our bathroom.

a necessary thing. If we can buy a better shower holder, then we don't have to worry about showering badly. When we choose a good shower and fixing the seat, we must first look at its material, then look at its appearance, and see if it does not conform to the overall style of the home in our own home.

How to install the shower rail holder

According to the actual needs of the installation position of the wall seat, according to the actual hole distance of the wall seat, the hole is turned in the selected position, the size of the hole is 6, mm, the depth is 35mm, the expansion sleeve is driven into the hole that has been turned on the wall, and then the base is fixed on the wall with self-tapping screws.

Fix the wall base on the base: There are two buckles above and below the base, and the wall base has been installed when you hear two "clicks".

The shower is a must-have in the bathroom, and the shower base is used to fix the shower, so it can not be missing, when people take a shower, if they don't want to hold the shower in hand, then the shower base plays a role, so don't underestimate the shower base, if the installation is not good, it will affect the use. The following is an introduction to how to install the shower seat and the precautions for the installation of the shower seat.

How to install the shower seat.

1. It is recommended that one shower seat is about meters above the ground, and the other is about meters. You can first put the decorative cup into the thread of the shower bracket, wrap the raw material belt, and screw the left and right shower brackets into the hot and cold water pipe joints respectively.

2. Adjust the distance between the front end of the shower bracket by 9 cm, the height should be consistent, and the distance between the wall should be consistent, put the water-stopping gasket into the water inlet hole behind the faucet body, and then install the shower faucet on the shower bracket, install the water nozzle, the outlet joint of the hot and cold water pipe is 1 2 inches of general caliber, preferably the type sun conical threaded joint of R1 2, the left is hot water, the right is cold water, the distance between the center of the joint is about 15 cm, and the height of the joint from the ground is recommended to be 60 cm.

Precautions for installation of shower seats.

1. Installation location.

Do not install the shower seat at the door or next to the window, you can consider where the shower mixer is installed when purchasing, and do not wait until the decoration is completed to find that it is not suitable.

2. Keep a plane with the wall.

The installation of the shower seat should be kept on a plane with the wall, if the reserved distance is too much, it will not be able to cover up the wire head and screws, and the reserved distance is too small to install the shower seat.

3. The height of the mixing valve from the ground of stuffy filial piety.

The height of the mixing valve from the ground is generally between 90cm-110cm, so that it can be decided according to individual needs, but not higher than 110cm and less than 90cm. The ideal height of the shower seat should be 20 to 30 cm higher than the height is the best.

4. Shower style.

There are a variety of shower styles on the market, and the installation methods are also different, including surface, concealed, ceiling, etc., and the owner can choose the right style according to the actual situation.

Loose treatment method of shower seat.

If the shower is loose, check what the reason is, if there is a problem with the soft rubber of the lifting seat or the card seat mat is loose, you can tighten it with a screwdriver, if it is loose and there is no solution to the rental draft, you can find a professional master to repair or directly find the merchant to replace the new one.

When choosing, we must consider the quality of the problem, then, we have to see how to disassemble the shower holder, if you want to replace the holder, you must see what his disassembly method is, secondly, but also to see how to use the shower, for some novel showers many people do not know how to use. Most people pay more attention to the bathroom when choosing the bathroom, because its quality is relatively important, so we must consider the quality of the problem when choosing, then, we have to look at how to disassemble the shower holder, if you want to replace the holder, you must see what his disassembly method is, secondly, you have to look at how to use the shower, for some novel showers many people do not know how to use.

How to remove the shower holder

Apply thread sealing paste or wrap sealing tape to both joints and screw them into hot and cold water supply pipes. Adjust the two joints so that their center distance is 150mm and keep them at a uniform level; The middle decorative cover is screwed into the joint, which is close to the wall after decoration; Attach the gasket to the nut, screw it onto the fitting, and tighten it. Insert the gasket into both ends of the shower hose, then connect one section of the shower hose to the outlet of the faucet and the other end to the showerhead.

How to install the bracket) first buckle the retaining pin from the bracket and remove the plastic cover. Remove the self-tapping screws and expansion plugs from the inner cavity of the carriage. At a height within reach of the shower hose, select a location for the mounting bracket.

Mark the wall with the number of the position of the base plate of the bracket and drill two holes according to the number. Insert the expansion plug into the hole, and then screw the self-tapping screw into the expansion plug through the plastic sleeve as shown in the picture, and tighten it with a screwdriver. Insert the grooves on the inner wall of the bracket into the boss of the plastic sleeve, and then press the pegs into the fixing holes of the bracket.

How to use the shower

1. The use of the rain shower is very simple, we can use it when we turn on the switch. There are hot and cold water in the shower, usually turn the switch to the right for cold water, and the left for hot water, and you can debug to the appropriate water temperature. Some shower showers belong to thermostatic showers, and there is a twist on the left and right sides of the faucet, and the knob on the left is used to adjust the water temperature; The knob on the right is used to control the way and amount of water outlet, and everyone can adjust the amount of water and water temperature according to their own needs.

2. Showers also need to be maintained in daily life. There will be water stains inside the shower after a long time, we can mix the white vinegar and water in proportion, and then put the shower head into it to soak 2, and finally we will rinse the shower clean. We can also take the shower apart and rinse the strainer and spout with water.

According to the knowledge mentioned in this article, I mainly understand how to disassemble the shower holder, the article has written out the specific steps for you, if you want to replace the base, you must, follow the correct steps in the article, so that it can be better replaced, and also tell you, how to use the shower is what the method is.

Summary. The question is simple, to remove the shower lift bar mount, first you need to find the nut of the mount. The nut is usually at the bottom of the shower lift bar, and it is used to hold the shower lift bar on the holder.

Using an appropriate tool, such as a wrench or wrench, loosen the nut. Once the nut is fully loose, you should be able to remove the shower lift lever from the holder. Remember to turn off the water source first to avoid wasting water or accidental jetting.

Good luck! The question is simple, to remove the shower lift bar mount, first you need to find the nut of the mount. The nut is usually at the bottom of the shower lifter, which is used to fix the shower lift rod on the solid celery seat. Using an appropriate tool, such as a wrench or wrench, loosen the nut.

Once the nut is completely loose, you should be able to remove the shower bar from the mount. Remember to turn off the water source first to avoid wasting water or accidental jetting. Good luck!

Fellow, I really didn't understand, I can be more specific.

Find the bottom nut of the shower lift lever and loosen it with a return wrench or wrench. After unscrewing the nut, you can remove the shower lifter. Remember to turn off the water source to avoid wasting or causing a jet. Good luck!

1. Take out the base of the shower, measure the size, aim at the water outlet hole on the wall, screw it with a wrench, don't tighten it too tightly, and adjust the position later.

2. Install the shower vertical rod, adjust the height, first punch holes with an electric drill for the fixed position of the vertical rod, pay attention to play slowly, and do not damage the wall tiles.

3. After punching, install the shower vertical rod holder, adjust the height, and then install the top sprinkler head of the shower, adjust the angle, and maintain balance.

4. Finally, tighten the screws of the shower base, install the base for the small sprinkler head or clamp it between the vertical rods, and connect the hose.

5. Turn on the switch, test whether the water flow is smooth, place a few pieces of toilet paper at the base, and observe whether there is water leakage the next day.