How to wash the shaver with full body water, how to clean the razor

At present, there are two types of washable electric shavers on the market, one is partially washable, and the other is fully washable. For electric shavers that support partial washing, remove the lower knife mesh and other washable parts and rinse them directly under the faucet after use, rinse them and dry them off before installing them back one by one. Remember, in particular, the place where the battery is installed and charged should not get wet, otherwise it may damage the shaver.

The shaver that can be washed all over the body is relatively more convenient to clean, and most of the current ** shavers such as Braun.

Almost all razors support full body washing. When cleaning this kind of shaver, you can directly pop out the cutter head, rinse the cutter head and grille, of course, the blade part does not have to worry about water, but it is recommended to dry the entire shaver after rinsing, and at the same time, in order to ensure the service life of the shaver, it is also recommended to regularly put some maintenance liquid on the shaver.

In addition to washing, in recent years, there has been another type of shaver cleaning mode, that is, the electric shaver itself carries the intelligent automatic cleaning center, such as Braun with CC series shavers are equipped with automatic cleaning center, this kind of shaver cleaning is more convenient, no need to manually clean, after using the shaver, directly into Braun's automatic cleaning center, press to quickly get the shaver clean, disinfect, lubricate, can be charged, with cleaning liquid sterilization rate can be achieved, It's the equivalent of using a new razor every day.

The simple and effective way is to use an ultrasonic cleaner for cleaning, which can easily clean out the grid residue and oil stains of the shaver, and the cleaning effect is visible to the naked eye.

The shaver can be washed directly into the ultrasonic cleaning machine for cleaning, ultrasonic cleaning can deeply shake out the dirt and oil, and can also effectively sterilize, which is a good cleaning assistant in family life.

Goodt Ultrasound. Good's ultrasonic ultrasonic cleaner.

Don't just wash the shaver with water, teach you the correct way to clean, clean and hygienic after washing, and increase your knowledge.

Cleaning of automatic shavers.

Standard cleaning. 1.The shaver head is soaked in 75% purity medical alcohol for 5 minutes (the entire shaver head is soaked in medical alcohol).

2.The head of the shaver is soaked in 75% pure medical alcohol, and the shaver rotation is started at the same time, starting for 20 seconds, then pausing for 20 seconds, and the cycle repeats for 4 minutes. (The head of the shaver is soaked in medical alcohol throughout the whole process).

3.Disassemble the shaver head and scrub the inside of the shaver head in medical alcohol. (3 minutes to 5 minutes).

4.Assemble the shaver and drain the head down for 1 to 2 hours.

Deep cleaning. 1.The shaver head is soaked in 75% purity medical alcohol for 10 minutes (the entire shaver head is soaked in medical alcohol).

2.The head of the shaver is soaked in 75% pure medical alcohol, and the shaver rotation is started at the same time, starting for 20 seconds, then pausing for 20 seconds, and the cycle repeats for 6 minutes. (The head of the shaver is soaked in medical alcohol throughout the whole process).

3.Disassemble the shaver head and scrub the inside of the shaver head in medical alcohol. (5 minutes to 10 minutes).

4.Assemble the shaver and drain the head down for 1 to 2 hours.

The program is based on the cleaning process of the Braun Shaver Automated Cleaning Center.

1. If you are a blade-type manual shaver, be sure to pay attention to changing the blade regularly. After using the razor, remove the blade and use a cotton swab or brush to clean off the residue such as stubble attached to the blade, and wipe it with water or alcohol to ensure that the blade is clean.

2. If the shaver is used more than 3 times, be sure to soak the blade for sterilization. Soak the blade in alcohol, remove it after about 3 minutes, and wipe it clean with a cotton swab to prevent rust on the blade.

3. The cleaning of the electric shaver is even more important, because the knife mesh of the electric shaver is precisely designed, and patience and care are required when cleaning. If you use it more than twice, you should clean it thoroughly, dip a cotton swab in a little alcohol, wipe the surface of the knife mesh, and then wipe the inner knife mesh to ensure the cleanliness of the knife mesh. After cleaning the knife mesh, open the knife mesh, remove the stubble inside, and then use the same method to clean the inside of the knife head, but you must remember that you should not scrape it with a hard object to avoid damaging the body.

The above is the razor cleaning method shared with you, you can learn about it if you need it, I hope it can help you.

The shaver full body washing means: the whole machine can be rinsed and cleaned with water flow, but it cannot be soaked in water for a long time, and the use function of the product will not be affected by just a few minutes.

There are several other modes of shavers:

1. Wet and dry use.

In addition to the full body wash, you can apply shower gel, soap foam, etc. to the head of the knife to shave together, the effect is better and more comfortable. Twist off the grille, dry and wet can be directly rinsed with tap water, and then the residual water is shaken dry. Even if it is a very safe waterproof design, once the sealing ring is damaged, liquid substances (water, disinfectant) will penetrate, which will lead to damage to the internal circuit board components and eventually lose the shaving function.

2. Charging and plugging.

It can be used on a full charge or plugged in (similar to a mobile phone).

3. The cutter head is washed.

The head of the electric shaver can generally be removed, but it can be cleaned with clean water, or it can be cleaned with the brush that comes with the product accessories, (but it should not be soaked for a long time) and the installation will be in place after drying.

If you are using a manual razor, remove the blade, use a cotton swab or brush to remove residues such as stubble attached to the blade, and wipe the blade with water or alcohol. Electric shavers need to wipe the surface of the knife mesh key ridge and the inner knife mesh, and the stubble inside the knife mesh needs to be cleaned.

The shaver is a tool for shaving and seeping the beard, and the root burner can be divided into a safety shaver, an electric shaver, and a mechanical shaver according to the structure.

The head of the shaver has a rotary type and a reciprocating type, and the shape of the shaver has a straight type, an elbow type, a horizontal type, and a double-head type.

If the shaver is used more than 3 times, the blade should be soaked and sterilized, and the whole shaver should not be soaked in water for a long time.