How to paste wallpaper, how to paste wallpaper The correct way to paste wallpaper and skills

1 Clean up wall decorations and shelves.

2 Apply a 1:2 ratio wallpaper remover evenly to the old wallpaper with a brush.

3 After the wallpaper remover has completely penetrated, remove the wallpaper with a scraper and hands.

4 Fill the hole in the wall with putty and level the wall with a scraper.

5 Measure the size of the wall, and then measure the wallpaper based on the wall area, pay attention to the length of the wallpaper, which is 5cm more than the actual veneer.

6 Then mix the powdered wallpaper glue with water and mix the general wallpaper with 1:3, the foamed wallpaper with 1:2 blending, or use the special glue for wallpaper that does not need to be prepared, and use the special glue for the blended wallpaper with a roller brush to evenly brush the back of the wallpaper.

7 Then put the wallpaper against the wall and stick it with a wooden brush from top to bottom and from the corners to make the wallpaper flat.

8 When encountering a power switch or socket, cover the wallpaper first and then brush it flat with a wooden handle, then use a utility knife to draw a cross diagonally on it, use a scraper against the edge of the switch, and use a utility knife to cut off the excess part.

9 If you encounter the connection of the printed wallpaper, find the consistent position of the pattern at the junction of the two wallpapers, overlap and paste about 12cm wide, and after the whole wallpaper is all aligned, use a scraper to resist, and then cut off the overlapping part with a blade.

10 Pay attention to brushing from top to bottom when pasting wallpaper, if you find uneven floating spots, you can use a towel to wet it, and then re-level it with a spatula.

11 Finally, the wallpaper around the door and window is processed in the same way as the wallpaper at the power switch.

12 After the wallpaper is pasted, it is completed to replace the original device. (

Grass-level leveling - batch putty - paste wallpaper (wallpaper knife, wallpaper glue) - wipe to clean the surface.

It's simple.

Substrate leveling - brush moisture-proof primer - paste wallpaper.

Buy utility knives and towels.

How to paste wallpaper? Wallpaper is a new wall material, which has become very popular. The use of wallpaper is good, simple and convenient, and the concept of environmental protection, so how to paste wallpaper?

Next, I would like to recommend to you the correct way to paste wallpaper and skills! How to paste the wallpaper, generally before pasting the wallpaper, the wall should be trimmed first, so that the wall is as flat as possible, so that the wallpaper is not easy to fall off. Then cut the wallpaper according to the measured size, apply professional glue, and you can paste the wallpaper on!

How to paste wallpaper? The first step is to treat the wall, and the flatness of the wall is relatively high for the wallpaper. If there are some foreign objects on the wall, or protruding parts, the pasted wallpaper will easily fall off.

Therefore, before construction, the wall should be sanded with fine sand paper. If there is any damage, you can also use plaster to repair it and keep the wall flat!

How to paste wallpaper? The next step is to measure the area of the wall, so that you can cut out the prepared wallpaper. But it should be noted that the cut wallpaper must be larger than the measured area, and the maximum is about ten centimeters more than ten centimeters, so that when constructing, it is not easy to make mistakes!

The extra part can be trimmed with a wallpaper knife after pasting, so that the trimmed edges will be more neat!

How to paste wallpaper? Once you've cut your wallpaper, you can apply glue to the back of the wallpaper. To apply evenly, it is best to leave it for about 5-10 minutes, so that the effect will be better.

When pasting, it is more convenient to start from the top and work downwards. You can also use a scraper to make the wallpaper stick closer to the wall!

The question of how to paste the wallpaper is all of the above! In fact, sticking wallpaper is still very simple, you don't need too much professional technology, just pay more attention to some details! So how to paste wallpaper, have you learned? ​

You can get it for free

Nowadays, many families will use wallpaper when decorating, wallpaper is modern and beautiful, and is deeply loved by consumers, thenThe method of pasting wallpaper is missingWhat are they? The following series will introduce the construction method.

How to paste the wallpaperHow to paste the wallpaperThe first method.

How to paste the wallpaperWhen the primer is treated to treat the surface of the primer, the primer must be cleaned so that it is free of dust, oil, and debris.

2. Before the elastic line, paste the wallpaper, first carry out the elastic line, the elastic line is the horizontal and vertical line of the base processing, so that there is a base for pasting, which is used to ensure the quality of the pasta.

3. Paper-cutting is an important part of wallpaper, after measuring the height from the top to the bottom of the wall, cut the paper on the floor, the size of the wallpaper should be 10 to 20 mm longer than the actual size, after wetting, it can stick, after penetrating water, it can be used for 10 minutes.

4. Glue brushing is the key link of wallpaper paste, to ensure the firmness of the paste, the back of the wallpaper and the wall should be brushed, the glue should be uniform, can not be filtered, can not be filtered, pay attention not to roll up, stack and stack, so as not to stain the wallpaper, the width of the wall brush should be 30 mm wider than the wallpaper.

5. The principle of wallpaper on paper is first vertical and horizontal, first up and down, first high and then low.

How to paste the wallpaper- The second.

1. Treat the surface of the wall: treat the existing impurities on the surface of the wall, and scrape the floating floor, gypsum powder is used to soften the cracks in the cavity, so that the wall is clean and firm, and the wallpaper is not easy to peel off.

2. Determine the size of the wallpaper: the length of the cut wallpaper depends on the height of the wall, under normal circumstances, the flower wallpaper will not be cut at the height of the wall of 5 to 8 cm, it is used for upper and lower trim, the length of the wallpaper increases according to the actual situation, and the length when cutting is usually 8 to 10 cm.

3. Use a glue brush to brush the wallpaper on the back of the glue and brush the wallpaper on the back; The perimeter edges should also be coated with glue to ensure the quality of the construction, the wallpaper should be bent under 5 glues to be applied for 10 minutes, allowing the glue to completely penetrate the bottom of the paper and can subsequently be released.

5. Cleaning and decoration: cut additional pads at both ends, and then use jellyfish to immerse the surface of the jellyfish with a sharp edge and avoid the paper wallpaper back yellow.

ForHow to paste the wallpaperThe introduction is completed, in fact, there are many details that need to be paid attention to in the decoration, of course, it is best to choose a professional crowd for wallpaper pasting, so that the effect will be better after completion.

You can get it for free

1.The construction surface must be solid, clean and flat, without peeling, cracks and cavities, and the wall surface must be dry;

2.First, use state-sensitive putty to flatten the veneer batch, and then polish it with sandpaper after it is dry; Then use diluted nitro varnish (wallpaper base film can also be used) to brush twice, and dry for 24 hours to keep the room ventilated;

3.Avoid damage or contamination caused by cross-construction;

4.All edge interfaces of wallpaper need to be closed in black corners or lines;

5.Wallpaper imported special glue should be selected, the amount of glue is appropriate, thin and even, if there is overflow, it should be cleaned up in time;

6.It is strictly forbidden to use an unclean wet cloth to wipe the surface, and it is advisable to use a dry cloth to dust off the dirt.

7.It is strictly forbidden to use sharp, sharp, hard, and angular objects to rush, scrape, and press on the surface of the wallpaper;

8.Wallpaper cutting should use a special wallpaper cutter; The cutting angle is 45 degrees. In order to ensure the seam effect, it is advisable to use the lap cutting method for cutting;

9.This wallpaper is recommended to use nitro varnish as the base;

10.This wallpaper should not be constructed in damp or rainy days;

11.This wallpaper needs to wear gloves for construction operation to avoid damaging the protective layer on the surface of the wallpaper;

12.This wallpaper should be constructed on rollers.

Nanjing foil seat technology specializes in the processing of a variety of gold and silver tiles, glass mosaics, gold foil wallpaper, decorative panels and other high-end gold and silver veneer decoration materials, welcome new and old customers to visit and buy, we wholeheartedly serve each volume of high branch a customer.

1.The first thing to do is measure the size of the wall.

2.Remove wall skin: Remove the original paint, wallpaper and other objects from the wall.

If there are cracks and potholes on the wall, use gypsum powder to make up for these places, and put bandages on them after leveling; If you encounter sand-gray walls and partition walls, you should also be covered with glass silk cloth or really good cloth; Some poor quality partition walls or exterior walls need to be nailed with gypsum board to achieve thermal insulation effect.

3.Crop the wallpaper: Measure the height from the top of the wall to the baseboard, then crop the wallpaper.

Do not cut the flower wallpaper by about 10 cm according to the height of the wall, and use it for trimming up and down; The symmetry of the pattern needs to be considered for the flower wallpaper, which needs to be more than 10 cm, and the flowers should be cut and numbered from the top of the plan, so that they can be pasted in order. In addition, the cut wallpaper generally needs to be soaked in clean water for 10 minutes before it can be brushed.

4.Brush the base film to scrape greasy: brush the bottom film, evenly brush the base film on the wall, and the thickness is moderate; Scrape putty and sand.

Scrape putty twice on the wall. After the putty is dried, polish the wall with sandpaper to grind off the uneven particles to make the wall smooth and flat; Paint the wall (cover paint) evenly again with a base film, without being too thick. This prevents the wall from absorbing the wallpaper glue, making the wallpaper stick to the wall and making the wall flatter.

5.Glue: In order to ensure that the paste is firm, the back of the wallpaper and the wall should be brushed, and the glue should be evenly painted, and the edge can not be wrapped and piled up to prevent the wallpaper from being stained.

Glue the wall 30 mm wider than the wallpaper. After brushing the glue on the back of the wallpaper, fold the glue side and leave it for 5 minutes, which can not only prevent the glue surface from drying out quickly, but also not be easily polluted.

6.Cutting wallpaper: Measure the length before cutting, generally standard wallpaper is 10 meters long and wide per roll, and can be paved with square meters. The other two sizes are 7 square rolls and 16 square rolls.

7.Pasteing: The principle is first vertical and then horizontal, first up and then down, first high and then low.

When pasting the first piece of paper, find the baseline at the corner of the wall, gently flatten it with your hands from top to bottom, from the middle to both sides, and then scrape with a scraper to make the wallpaper and the wall solid. When pasting the second piece of wallpaper, overlap the overlap with the first sheet by 20 mm, use a wallpaper knife to cut off the overlapping part, remove the remaining part and scrape it flat with a scraper. It should be noted that the glue extruded from the wallpaper should be wiped with a wet towel in time to avoid the wallpaper turning yellow over time.

Step 1: Now cut the wallpaper according to the required size, pay attention to the cutting size left at both ends Step 2: Add water to the wallpaper glue and mix it evenly and viscous.

Step 3: Paint the wallpaper glue to the wallpaper, pay attention, the glue should be even, to the edge of the fourth step: wallpaper on the wall, there is a wallpaper scrape to scrape out the bubbles in the middle, use a wallpaper knife to cut off the edge of the excess wallpaper. ok

Select **, right-click, and select Set as Background Pattern. OK.