How to paste wallpaper? How to paste wallpaper?

How to post wallpapers in generalThe tools and materials used are: glue, brushes, towels, sponges, sandpaper, cutters, scrapers, tape measures, glue containers, etc.

1) The basic procedures for posting are:

1. ?Wall Treatment:

Use a scraper and scrape off the impurities on the wall, scrape off the floating soil, and pave the holes and cracks with gypsum powder, such as the soft texture of the wall or the powder layer and the emulsion paint swept overThe wallpaper base film should be painted once (but I personally think that varnish or varnish will be better, but varnish and the like are not environmentally friendly), so that the wall is firm, and the wallpaper will not fall off. ?

2. ?Crop wallpaper:

Measure the height of the wall first, and then cut the length of the wallpaper, there are two situations: do not cut the flower wallpaper according to the height of the wall to add about 5 to 8 cm in length, ?Use it for trimming up and down:

For flower wallpaper, the symmetry of the pattern needs to be considered, so the cutting length should be increased according to the actual situation, usually 8 to 10 cm longer. ?3.

Brush glue: Brush the wallpaper glue on the back of the cut wallpaper with a brush, and pay special attention to the edges around it must be coated with glue to ensure the quality of construction

The painted wallpaper should be folded and placed for 5-10 minutes (note, no external force should be applied to avoid creases in the wallpaper, especially the cloth) so that the glue can be posted after completely penetrating the bottom of the paper, and several pieces of wallpaper are painted each time, and posted in order. ?4.

Wallpaper construction: generally the first wallpaper is posted from top to bottom on the side of the door or in the dark corner, and the scraper is used from top to bottom, from the inside to the outside

Gently scrape the wallpaper and squeeze out the bubbles and excess glue to make the wallpaper flat and close to the wall. ?5.

Trimming and cleaning: cut off the excess wallpaper at the upper and lower ends, the knife edge should be sharp to avoid burrs, and it is best to use a Japanese imported blade that sells a piece of yuan on the market when cutting some wall cloths.

Then use a sponge dipped in water to completely wipe the glue remaining on the surface of the wallpaper to avoid the wallpaper from turning yellow, after the wallpaper is dry, if there are bubbles on the surface, cut it with a knife and inject the glue and then flatten it to eliminate it (it is better to use a syringe).

The normal steps to <> wallpaper are as follows: 1 Measure the area and size of the wall first, so that you can get the area and size of the wallpaper that needs to be posted.

2 Remove the wall skin. Remove the original paint, wallpaper and other objects on the wall first; If there are cracks and potholes in the wall, these areas should be filled with gypsum powder, leveled and then bandaged; If you encounter partition walls and sand-gray walls, they should also be covered with glass silk cloth or good cloth; Some poor quality partition walls or exterior walls need to be nailed to gypsum board in order to achieve the insulation effect.

3 Crop wallpaper. Measure the height from the top of the wall to the baseboard, then crop the wallpaper. The wallpaper that does not belong to the flower should be cut about l0 cm more according to the height of the wall, and it is used for trimming up and down.

The symmetry of the pattern should be considered for the flower wallpaper, which needs to be more than 10 cm, and it should be on the flower from the top. Once you've planned it, start cutting and numbering it so that you can paste it in order. In addition, the cut wallpaper usually needs to be soaked in clean water for 10 minutes before it can be brushed.

4 Scrape putty after brushing the bottom film on the wall. Brushing the bottom film is to evenly brush the base film on the wall, the thickness should be moderate, and then scrape the putty, polish, and scrape the putty twice on the wall in total. After the putty is dry, then use sandpaper to polish the wall to grind off those uneven particles to make the wall smooth and flat; Paint the wall (cover paint) evenly again with a base film, this time not too thick.

Doing so will prevent the wall from absorbing the wallpaper glue, allowing the wallpaper to stick firmly to the wall and making the wall flatter.

5 Brush the glue. In order to make the wallpaper firmly pasted, the back of the wallpaper and the wall should be glued. The glue should be evenly brushed, not wrapped and piled up, so as not to stain the wallpaper.

When gluing the wall, the width of the glue should be 30 mm wider than the width of the wallpaper. After brushing the glue on the back of the wallpaper, the glued surface should be folded in half for 5 minutes, which can not only prevent the glue surface from drying out quickly, but also not be easily contaminated.

6 Palate. In principle, it is to grind straight and then level, first up and then down, first high and then low. When pasting the first piece of paper, you should find the baseline at the corner of the wall, gently smooth it with your hands from top to bottom, from the middle to both sides, and then use a scraper to scrape it, so that the wallpaper and the wall are slowly solid.

When pasting the second wallpaper, the overlap with the first sheet should overlap by 20 mm, use a wallpaper knife to cut off the overlap, remove the remaining part and then scrape it flat with a scraper.

It is necessary to pay attention to the fact that the glue extruded from the edge of the wallpaper should be wiped clean with a wet towel in time, otherwise, the wallpaper will turn yellow after a long time, affecting the service life of the wallpaper.

Wallpaper is a relatively technical job, but if we pay attention to some details, we can DIY a personalized room by ourselves.

Preparation. Prepare construction tools: 2 buckets, 2 towels, sponges, scrapers, plumb weights, brushes, paper knives and blades, and clean plastic sheets.

1. Wall treatment.

The degree of treatment of the wall is related to the effect of the wall on the wallpaper, so after entering the site, the first thing to observe is whether the owner's wall is flat. And use sandpaper or scraper to go through the wall. The fine particles on the wall will affect the beauty of the wallpaper.

If there are cracks in the wall and the wall is too wet, you must contact the owner and deal with it before you can carry out wallpaper construction.

2. Brush the base film.

Ensure that the wall surface is flat and prevent moisture from spreading. Different qualities of putty and lacquer on the market will affect the treatment of the wall. The base film is basically an environmentally friendly product, and it has gradually replaced the coating.

3. Gluing. The company uses Henkel brand rubber powder. The general gluing is applied on the back of the wallpaper. The ratio of glue powder and water should be appropriate, and the wallpaper should be pasted on the wall in time after being glued. The glue should not be too dry (it cannot be pushed when it is on the flower).

Fourth, paste wallpaper small theft door:

1. Problems with American wall coverings:

It is easy to produce bubbles. Solution: Start from the middle and brush flat with a brush.

Advantages: scrubbing, strong and durable, the modeling wall will have a good phenomenon of nest edge, it is recommended to use a hair dryer in winter, it can be softened and shaped after blowing, and the high temperature makes the water disperse quickly and sticky well.

Edge tailoring process: used in the case of raw edges, mostly used in Japanese paper, (the purpose of the protective belt when cutting the letter vertical loss paper: to prevent overflow) in the upper and lower trimming with protective tape to protect the top surface.

The protective belt is a relatively thin plastic film, and you can buy some rolls of plastic paper locally and cut them into small rolls for use.

Non-woven fabrics, cloth pulp filament: do not overflow glue, be careful.

If the seam is overflowing, wipe it with a sponge, not a towel.

The cloth surface can not overflow the glue, easy to produce color difference, the cloth surface is used more in the master bedroom, less in public places, sucked with a vacuum cleaner, the glue is moderate, and the seams are very demanding. Hygiene must be good, the blade is not fast and easy to fluff.

The cloth material has very high requirements for the wall, and it will bulge if it is not handled properly.

Pure paper, thin, shiny wallpaper: high requirements for the wall, the requirements for the glue should be very pure, the glue bucket should be clean, and the glue should be thin and thin.

Pair the flowers first and then trim the edges. Fast and good.

Don't be in a hurry to trim the edges, you must first get the edges right.

You can get it for free

a.The bottom of the wall should be treated solidly, first of all, there can be no depression or bulge, and there can be no concave and convex small particles, the smoother the water-resistant putty to be treated, the better, before pasting the wallpaper, it must be on a clean oil, so as to seal the bottom of the wall, otherwise it will eat glue bPlain wallpaper is the best paste, the loss is also the minimum, there is some loss of the wallpaper of the flower, about 5-10%, (according to the wheel base of the color), as long as the oilman is careful, the flower is not a problem C

Glue brushing is the key link of wallpaper paste, in order to ensure the firmness of the paste, the back of the wallpaper and the wall should be brushed with glue, requiring the glue to be evenly brushed, tight, can not be missed, pay attention to not wrapping, piling, piling, in order to prevent staining the wallpaper. The wall should be glued 30 mm d. more than the width of the wallpaperBe sure to dry paste, do not wet paste, dry paste is to evenly glue on the back step of the wallpaper, and then dry for 5 minutes, and then go to the wall to the flower with a scraper to drive out the remaining glue, and so on, wet paste is to throw the wallpaper whole roll into the water to soak, and then brush the glue on the wall, wallpaper on the wall, this process is easy to cause the seam to open the glue, because the whole roll of paper in the water, the water absorption rate of the outer layer and the inner layer must be different, and the shrinkage of the wallpaper after drying on the wall is not the same, so it will be curled or opened e

Standing one meter away from the wallpaper during acceptance, the seams can not be seen within 2 seconds or are not obvious, the flowers are neat, the seams are not yellow, basically it's OK, but there is a situation to pay attention to, some wallpapers because of the relationship between the flower type or color, against the strong light, you can see the seams, this is no way to solve, but when choosing wallpaper, choose some light colors or thick patterns (imitation cloth pattern), basically it will be much better!

Flatten the base film with water and stir evenly Brush the wall with a roller, brush it again after drying, soak the glue used for the sticker, be sure to stir evenly, cut the wallpaper, and put it on the wall.

Construction according to the following procedures: base treatment, brushing closed primer, pay-off, paper cutting, glue brushing, mounting.

First of all, the wall itself should be smooth without peeling cracks, and then open the base film with water and stir evenly with a roller brush on the wall, the base film will generally dry in half an hour, and you can brush it again after drying, and then you can soak the glue with the sticker, pay attention to the glue because there are pimple stickers will be obvious, so be sure to stir evenly, and finally calculate how long a piece of paper needs to be according to the wall height and the wallpaper on the flower, and then cut the wallpaper, and then brush the glue on the back of the wallpaper to go on the wall, and the first one must be vertical when pasting it. No, then the side will follow crookedly.

Do you want to post it yourself? Don't post it if it's not professional. Otherwise, the effect is not good-looking, and the wallpaper is wasted.

When pasting wallpaper, first scrape the putty layer on the wall, polish it flat, and then apply a layer of base grinding. You don't need to paint the wall. After two or three days, put the wallpaper again.

The longer the base grinding is done after the interval, the better. When pasting wallpaper, use special wallpaper glue mixed with water and stir evenly. Then rinse it on the back of the wallpaper.

Stick it on the wall. Not to mention the unprofessional slowness, it is difficult to deal with the side seams and not see the splicing.

It's best to find a professional wallpaper person to put it on.

It is recommended to find a professional master to help you paste it.

2. Measure the size of the wall, and then measure the wallpaper based on the wall area, pay attention to the length of the wallpaper, which is 5cm more than the actual veneer.

3. Then mix the powdered wallpaper glue with water and the general wallpaper at 1:3, and the foamed wallpaper with 1:2 to reconcile, or use the special glue for wallpaper that does not need to be modulated.

4. Then put the wallpaper against the wall, and paste the wallpaper from top to bottom and from the corners to the inside with a wooden handle brush to level the wallpaper.

5. When encountering a power switch or socket, cover the wallpaper first and then brush it flat with a wooden handle, then use a utility knife to draw a cross diagonally on it, use a scraper against the edge of the switch, and use a utility knife to cut off the excess part.

6. If you encounter a connection by the printed wallpaper, find the consistent position of the pattern at the junction of the two wallpapers, overlap and paste about 12cm wide, and after the whole wallpaper is all aligned, use a scraper to resist, and then cut off the overlapping part with a blade.

7. Pay attention to pasting wallpaper from top to bottom, if you find uneven floating paste, you can use a towel to wet it, and then re-level it with a scraper.

8. Finally, the wallpaper around the door and window is processed in the same way as the wallpaper at the power switch.

9. After the wallpaper is pasted, the original device is installed.

Question: I bought the glue on the original paper, is it right for the gaps.

1: Songyu liquid wallpaper 2: Huafang liquid wallpaper 3:

Eastman Liquid Wallpaper 4: Martin Liquid Wallpaper 5: Yimijia Liquid Wallpaper 6:

Wan Lei Liquid Wallpaper 7: Thumb Liquid Wallpaper 8: Sigm Liquid Wallpaper 9:

Bimet Liquid Wallpaper 10: Aubang Liquid Wallpaper ??Remarks:

The above liquid wallpaper brand is currently a more formal operating brand on the market, and are production-oriented enterprises, of course, there may be a small list of production enterprises are not listed one by one, China's current liquid wallpaper industry companies have about 300 large and small, but less than 20 production-oriented enterprises, most of which are ** nature. ?This ranking is based on:

According to the company's establishment time, it is ranked in order, and if there is an error in the middle, it may not be large.

The surface is coated with a dry paste, and only when you use it.

1. The construction points of wallpaper.

1) Remove the wall skin and remove the original paint, wallpaper and other objects on the wall; If there are cracks and potholes on the wall, use gypsum powder to make up for these places, and put bandages on them after leveling; If you encounter sand-gray walls and partition walls, you should also be covered with glass silk cloth or really good cloth; Some poor quality partition walls or exterior walls need to be nailed with gypsum board to achieve the effect of thermal insulation;

2) Brush the primer: brush the alkyd varnish evenly on the wall with a moderate thickness;

3) Scraping putty and grinding: Scrape putty twice on the wall. After the putty is dried, polish the wall with sandpaper to grind off the uneven particles to make the wall smooth and flat;

4) Cover oil: Paint the wall evenly again with clear oil, without being too thick. This prevents the wall from absorbing the wallpaper glue, making the wallpaper stick to the wall and making the wall flatter;

5) Cutting wallpaper: Cutting wallpaper also has regularity, such as each wallpaper and adjacent two wallpapers, the color and pattern of the neatness, the size of the same and so on;

6) Paste wallpaper: Use a roller to evenly apply the wallpaper glue to the wallpaper, and leave it for a period of time for thicker wallpaper. When you start to paste wallpaper, for the seams, squeeze the two sides of the adjacent wallpaper together to make them match, and then use a scraper to press the seams and clean up the extruded glue.

After the wallpaper is pasted, use a scraper to roll out the wallpaper from top to bottom.

2. Problems that are easy to arise in wallpaper paving.

1) Wallpaper paving is prone to problems such as glue opening, uneven parquet, and yellowing of joints. The main reason is that most of the construction personnel in China have not undergone professional training, and the quality of workers is generally not high. In addition, workers do not understand the characteristics of the wallpaper is also the main reason for the glue opening, uneven parquet, and yellowing of the seams.

First of all, it is necessary to have professional construction tools, such as glue rolling machines, brushes, rollers, professional knives, etc.;

Workers should be familiar with the characteristics of wallpaper, especially for pure paper, diatomaceous earth or wallpaper with a rough surface, we must pay attention to the excess glue can not be left in the seams when paving, if the residual glue is not clean, there will be glue in the future, yellowing and other phenomena;

For the corners, it is necessary to use professional edge banding glue to avoid cracking;

When parquet, it should be neat, and the knife should not be stubble.