How to set up a TP LINK router with wires

First, plug the network cable from the telecom into the WAN port of the router, and plug the computer into the LAN port of the router;

Then set the IP address in the computer to the last digit of the address is non-1), the subnet mask is, the gateway is, open IE after restarting, enter in the address bar: The router is generally this address, if not, please consult the router manual, and modify the gateway settings of the computer accordingly);

Enter admin and password admin in the page that opens (the initial and password of the tp-link router are generally like this, if not, please refer to the router manual);

On the management page, select WAN port settings under Network Parameters, select WAN port connection type as Static IP if the network cable is directly connected to the home, and fill in the IP address, subnet mask, gateway, DNS server, and standby DNS server provided by the service provider. If it is a ** line to enter the home, dial-up Internet access through the broadband modem, select "WAN port connection type" as "PPPOE", fill in the Internet access and Internet password provided by the service provider, and select "automatic connection, automatic connection after the service mu is turned on and disconnected";

Click "Save" and select "DHCP Server" on the page, click "Enable", fill in the start address (the minimum is and the end address (the maximum is, the address lease period is directly missing and the maximum value is filled in, and then click "Save" and select "Restart Router" under "System Tools" on the page, so as to complete the router settings.

Method.

1. Router B settingsDynamic IPSurf the Internet

1. Connect the computer to TP-Link router B with a network cablelan), any of them; A and B routers do not need to be connected with network cables for the time being.

Only connect your computer to your wireless router.

2. Enter the setting interface of the B router, click "Network Parameters" - WAN port setting "- WAN port connection type" Select: dynamic IP - > click "Save".

TP-Link Router B sets dynamic IP for Internet access.

> click "Save", after which you will be prompted to restart your router.

Change the IP address of the LAN port of TP-Link Router B to

4. Prepare another network cable and connect one end to the middle of A. On any interface, the other end of the network cable is connected to the WAN interface of B.

The LAN port of Router A is connected to the WAN port of Router B.

After completing the appeal setting, as long as Router A can access the Internet, then Router B can also access the Internet; The computer can be connected to the interface of the B router to access the Internet, and the wireless terminals such as mobile phones and laptops can also access the Internet when connected to the wireless network of B.

Method.

2. Use B as a wireless switch

1. Connect the computer to any one of the LAN of the TP-Link router B with a network cable; A and B routers do not need to be connected with network cables for the time being.

Only connect your computer to your wireless router.

2. Modify the IP address of the LAN port of the B router: click "Network Parameters" - LAN port setting "- IP address" to modify to: - Click "Save", and then it will prompt you to restart.

Change the IP address of the LAN port of TP-Link Router B to .

3. Prepare a network cable and connect it at one endaThe LAN (1 2 3 4) interface of the router is connected at the other endbRouter'slan(1/2/3/4) idle interface, note that you must not connect to the WAN interface of the B router.

4. Turn off the DHCP server on the B router: click "DHCP server" - DHCP service "- DHCP server" Select: not enable - > click "Save".

Shut down the DHCP server of TP-Link Router B.

If you want to use the wireless wifi on the B router, you only need to set the wireless wifi name and password on the B router, and you don't need to make other settings.

Method 2 Summary:

1. Modify the LAN port IP of router B and the LAN port IP of router A in the same network segment;

2. Close the DHCP server on router B;

3. The LAN interface of Router A is connected to the LAN interface of Router B.

The above two methods can realize the wired bridging Internet access between TP-Link routers, and users can choose any method to set up according to their own needs. If you encounter problems during the setup process, please read the article carefully to make sure that the steps are consistent with the steps in the tutorial and the order of the steps is consistent. You can also leave a message in the back, and the administrator will answer everyone's questions in a timely manner.

Tools Raw Materials: routers, network cables, broadband cats, computers.

The wireless wifi of the router can be used normally, and the router needs to be set up in the system, and the setup steps are as follows:

2. Then open the browser and enter the management address and login password of the device.

<>3. After logging in to the background, click on the setup wizard, and then fill in the corresponding parameters according to the instructions of the wizard.

<>6. After the wireless setting is completed, click Save, and then restart the router to use it normally.

2. Router reset steps:

1. Press the "reset" button directly on the router, the reset key is generally located behind the router, a recessed button, you need to press and hold the button with a slender thing (such as a toothpick, etc.) for tens of seconds, then the router can be reset. The equipment of each manufacturer is not the same, generally press and hold for a few seconds, and then turn on after the front lights are all off, that is, the reset is successful.

Note: Do not connect the network cable between the router and the broadband modem, connect the WAN port of the router and the LNA port of the broadband modem, and then connect the LAN port of the router and the network card of the computer.

Routing Setup Question DHCP Server Is On On.

Mac bindings are turned off.

Wait, too much!! Find it yourself slowly.

Setting up a manual IP is fine, you must have set the IP, not the DNS server:

You've got the DNS settings done!

If this is not the case, then it is recommended that you factory reset the route and then reset the route!

If it doesn't work, go to the next upgrade firmware package on the Internet to upgrade the software version of the router!!

First, connect the line first, as shown in the figure below;

2. Enter the router to set up broadband dial-up Internet access;

1. Look at the nameplate or manual at the bottom of the router, find the router IP, default login account and password;

2. Open the IE browser and enter the router IP, such as:

3. Enter the router login interface and enter the default login account and password.

4. Enter the router settings interface, find the first one on the left menu, set up the wizard, and set PPOE to automatically select the Internet mode, enter the broadband account and password, and set the WiFi password according to the prompts;

5. Save and restart the router after setting it to access the Internet.

You should refer to the IP settings of your notebook. If it is automatic, it is automatic, and if it is manual, it is manual. As long as the mantissa of the desktop IP is not the same as the mantissa of the IP of the laptop.

Remake the router with small buttons on the back of the router.