How much does it cost per square meter of floor heating installation and the installation steps

It feels cold in winter, especially in the north where the winter is cold, so every home in the north uses underfloor heating. Underfloor heating is the increase in the temperature of a room by heating the entire floor to heat it and keep it dry, which is very popular among consumers. So,How much is the floor heating installation per square meter

What are the installation steps for underfloor heating? Let's find out.

How much is the floor heating installation per square meterFloor heating in the market is divided into carbon fiber floor heating, electric floor heating, etc. Among them, the heated grounding wire has a single guide and a double guide.

The double-guided heating is around 150 yuan to 190 yuan per square meter, and the single-guided heating is 130 yuan to 170 yuan per square meter. Electric floor heating is about 120 yuan to 200 yuan per square meter, and carbon glass floor heating is about 140 yuan to 200 yuan per square meter. However, the cost of underfloor heating will be affected by the economic situation in different regions and therefore will vary.

1. First of all, level the floor, because the floor is uneven, it will directly affect the insulation effect of floor heating, because sharp objects will also cut off the floor heating pipe. At the same time, when there are bumps on the floor, they must be removed first, and the corners of the walls and floors must be at a right angle of 90 degrees.

2. The installation of the water collector must be installed in the horizontal position of the drawing, the water collector must be above, the water collector must be below, and the space must be kept at 20 cm. In addition, the height of the center of the water collector shall not be less than 30, and the installation effect will be more firm.

3. When the insulation layer is applied, it must be leveled first. The joints between the joints must be firmly bonded and the insulation must lie flat. When the reflective film is placed on the heat shield, it should be kept flat, should not appear wrinkled, and should be sealed.

4. The structure of the coil must be consistent with the design loop, and the separation of the road surface must be accurate. When it is close to the outer wall and exterior windows, its pipes are more stringent due to high heat loss, and plastic pipes must be used to fix the pipes in composite insulation panels and reflective films.

5. The filling of the floor is usually done with cement mortar. First of all, the concrete must be leveled first, and the size must not exceed 5 mm. Secondly, when the concrete is paved, the location of the door, the corridor, etc., it is necessary to make a mark to avoid the construction of the pipeline, which will later be destroyed.

Editor's summary: The above is explainedHow much is the floor heating installation per square meterand installation steps for underfloor heating. However, with underfloor heating, the temperature cannot be too high, because the temperature in the room suddenly rises, which affects not only the damage to its components, but also its service life.

The installation process of underfloor heating is as follows:1) Before the installation of floor heating, the floor screed should be inspected.

2) The manifold is horizontally fixed on the wall with 4 expansion bolts, and the installation should be firm.

3) Paste the 10mm corner insulation board along the wall with latex, and the paste is required to be flat and tightly lapped.

4) lay the insulation layer on the leveling layer (such as 2cm thick polystyrene insulation board insulation membrane or imported insulation film, etc.), paste the seam firmly with glue, lay aluminum foil paper or paste a composite aluminized polyester film with coordinate grid line on the Beijing floor heating insulation layer, and the insulation layer should be laid flat.

5) Lay a layer of medium 2mm steel wire mesh on aluminum foil, with a spacing of 100 100mm and a specification of 2m 1m, lay it strictly and tightly, tie it with a cable tie between the steel mesh, and fix the uneven or warped parts on the floor with steel nails. Nails are not allowed to be fixed in rooms with waterproof layers, such as bathrooms and kitchens, and measures should be taken to prevent pipes from exposing the concrete surface when the pipes or steel mesh are warped.

6) According to the heat load calculation requirements made by the professional floor heating company, the floor heating pipe (Pert pipe or PB pipe) is clamped with the floor heating pipe card to fix the pipe on the benzene board, and the spacing between the fixed points is not more than 500mm (according to the direction of the pipe length) The two ends and the midpoint of the curved pipe section greater than 90 ° should be fixed. The bending radius of the pipe should not be less than 8 times the outer diameter of the pipe. During the installation process, the pipeline should be prevented from being polluted, and the nozzle should be blocked in time after the floor heating pipe of each circuit is laid.

The villa master provides you with local building policies, building drawings, and villa design drawings;

Villa appearance renderings service, thousands of popular drawings for you to choose.

Villa Master.

Nowadays, people are living more and more comfortably in their homes. In order to make life more comfortable for yourself and your family, it is very important to choose the right heating equipment in winter. Underfloor heating is the heating device of the home.

So,How much does a home floor heating install？And how to install underfloor heating?

1. Material cost.

How much does a home floor heating installAt present, the installation cost of water and floor heating materials per square meter on the market is about 200-300 yuan. The differences between different materials are still relatively large for different regions.

2. Installation costs.

The installation cost of underfloor heating includes the installation of floor heating pipes, which is about 80 yuan per square meter. However, if gas boilers, thermostats, manifolds, and related accessories are included, it ranges from $150 to $400.

3. Calculate according to the load.

How much does a home floor heating installFor a 100 square meter apartment, if a heat load of 13kw per hour is required, the day will be calculated as 12 hours, and the total electricity bill will be about yuan per day, and about 6552 yuan in the first quarter.

1. Pre-installation.

When installing underfloor heating, first determine the design drawings, then clean the site, prepare for the installation of temperature control lines and manifolds, this part is very important, only after the installation of these, the trench and assembly can begin.

2. Full installation.

Bury the temperature control line and install the water collector in a suitable location. At this point, the grounding insulation and heating pipes can be laid. This step is simple, but attention to detail should be taken.

3. Lay the insulation layer.

The insulating board should be cut according to the size and then laid. When laying pipes, leave gaps in the pipes. First of all, the insulation is laid. Pay attention to the tightness when laying. In particular, the edges should be glued with adhesive tape.

4. Lay pipelines.

In order to prevent heat loss, a special insulating sleeve needs to be placed on the pipe from the water collection pipe to the installation room, and one end of the pipe should be connected with the temperature control valve and fixed with a special plastic card. Prevent loosening.

5. Stress test.

After the water has been preheated, cold water can be injected into the pipes. After the water is filled, the pressure can be sealed for 24 hours with a special press. If the pressure is sufficient, it can be used.

You can get it for free