d link DI 524M is slow after setting

If you suspect that your Wi-Fi has been stolen and you don't use Wi-Fi, you need to find the Wi-Fi settings and turn off Wi-Fi in the settings options, so that no one else can steal your Wi-Fi.

In addition, you can allocate the appropriate amount of traffic to each machine within the traffic limit, so that one machine will not be disconnected because one of the machines is taking up a lot of traffic.

In addition, if you are a user who has a limited time to access the Internet every month, please pay attention to the choice of connection mode in the manual configuration interface, the connection mode is generally automatic connection by default, that is, as long as the router is turned on, the network will be automatically detected, and if the connection to the network is normal at this time, it will be automatically connected to the Internet, regardless of whether you turn on the computer to surf the Internet, so please also turn off the power without using the router, so as not to cause high network costs.

Good luck!

Method: [Home Network Environment Wiring]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Manually changing the IP address of one of the computers will solve the problem.

Didn't you dial in with a router?

And is there a conflict of IPs?

1. First, connect your computer and router to the network. Connection method, connect the cable from the ADSL cat to the WAN port of your router, and the remaining LAN port can be connected to your computer or switch.

2. Then set your IP address to Zheng Jing or, subnet mask, (here look at the manual in your router, yes or, if yes, then your IP is set to the default gateway or all the way to determine, DNS is set to your own place shall prevail, call**broadband customer service asked, or search for what your DNS there is, such as, Xi'an Telecom's DNS, and backup, 3, and then open the IE browser, enter in the address bar.

After entering. The screen prompts you to enter the username and password, and fill in the default username and password of the router (the username and password of the router I use are admin, and you can refer to the manual for other routers).

Or open the Internet Explorer browser and type it in the address bar.

After entering. The screen prompts you to enter the username and password, and fill in the default username and password of the router (the username and password of the router I use are admin, and you can refer to the manual for other routers).

Read the manual, try your router address to set it.

4. After entering, the setting wizard will pop up, if the filial piety lead does not pop up, it doesn't matter, click "Setup Wizard" in the navigation blue on the left, and the wizard welcome message appears on the right, click "Next".

5. Select "ADSL Virtual Dialing (PPPoE)" and click Next.

6. Enter the username and password, which are the username and password you use when you use ADSL to dial.

7. Click Finish

If you are using a monthly subscription, it is recommended that you do the following work next. If you're timing it, it's recommended that you skip straight to the DHCP settings section.

8. Click "Network Parameters" - WAN Port Settings" in the navigation pane on the left

9. Select "Auto-Connect" and click "Save".

In this case, the broadband connection part has been set up, you can click on the "Running Status" in the left navigation window, and click to check the WAN port status in the right window. If the "Disconnect" button appears (don't click it), the connection is normal.

D-Link DI-524M is a wireless router Do you want to set up wired or wireless.

There may be a problem with the network cable, I don't understand hi me.

I thought that the wide loan was with wireless and wired, and if you don't understand, you can find me.

Broadband account encryption, right? Can I use the dial-up connection that comes with the system?

If possible, upgrade the router firmware and test it.

For D-Link wireless routers, the basic configuration is as follows:

1. Log in to the router configuration page.

Open the browser and enter it in the address bar, the default user name of D-Link is admin, and the password is empty.

2. After logging in, choose to manually set up the Internet connection, according to your network access type to set up, there are generally three kinds, 1) DHCP: that is, the operator only provides you with the line, no other information, plug the network cable into the computer to access the Internet, in this case, the access mode is DHCP, and then click Save;

2) Static IP: Static IP, that is, the operator provides you with IP address, subnet mask, gateway and DNS address, then you need to choose the static IP method, and then fill in the above information into the router to save;

3) PPPoE: This is more commonly used, most of them are ADSL, that is, the operator provides you with a username and password, dial-up to access the Internet, then you need to choose the PPPoe method in the router, and then fill in the username and password into the router, and the following connection method selection is always.

As of now, the router can be connected to the Internet, of course, you also have to check whether your physical wiring is correct, and the incoming cable given to you by the operator should be plugged into the WAN (Internet) interface of the router.

3. Set up wireless.

In the wireless settings, you need to change the SSID (wireless network name), and then encrypt it, and it is recommended to use WPA WPA for encryption, and the password is 8 digits or more digits or more digits or letters.

Check the model number, whether it is DI-524M.

And then pass. Log in to the router management page, the default username is admin, and the password is empty.

Configure the Internet part first, or you can also do it through the setup wizard, and select dynamic IP, static IP or PPPoE for access.

a.Dynamic IP (DHCP): That is to say, the operator only provides you with the line, there is no other information about the reputation, plug the network cable into the computer to access the Internet, in this case, the access mode is DHCP, and then click Save;

IP: Static IP, that is, the operator provides you with IP address, subnet mask, gateway and DNS address, then you need to select the static IP method, and then fill in the above information into the router to save;

This is more commonly used, most of them are ADSL, that is, the operator provides you with a username and password, dial-up to the Internet, then you need to choose the PPPoe method in the router, and then fill in the username and password into the router.

For the wireless network part, it is recommended to modify the SSID (i.e., the name of the wireless network) to distinguish it from other wireless networks, and the SSID can be represented by letters or numbers; If there are many wireless networks around and the corresponding SSID cannot be found, you can modify the wireless channel to avoid co-channel interference. Finally, it is recommended to encrypt the key with 8 or more digits of numbers or letters, and choose WPA or WPA2 encryption methods.

The above configuration can also be found in the Quick Installation Wizard.

The speed of Internet access is not unrelated to the hardware of the computer or mobile phone, but it has little to do with it.

The speed of Internet access is mainly related to the following factors:

One is the transmission medium; The second is the transmission rate. At present, the medium of the backbone network is optical fiber, which is the best medium at present, and most places have realized optical fiber to the home, so the medium of the backbone network is beyond question. The problem is that the quality of the indoor line is worth it**, although it has been fiber-to-the-home, but the network speed from the indoor to the terminal is 4m.

In addition, the transmission rate is related to the service provider, fortunately, China Unicom has entered the 4G era, and other service providers are also improving their network speed, which is also good news for users. But China's internet speed ranks 98th in the world, why? I think most of the reasons are:

First, the line is aging, the quality is not high, the layout is unreasonable, and the key is that the "last mile" problem has not been solved; The second is that the maintenance service can not keep up, many service providers only know the charge, but less service quality improvement; Third, from an objective point of view, China has a large number of users and relatively many problems of network congestion.

Judging from your situation, it should be a problem with the router, try it with good quality and function.

Good luck!