dlink di504 setting problem, high score, rush !!

You're getting it wrong.

1 One account can only be connected to one computer. If someone runs a network, they have already used an account, and if you go to the route, the post and telecommunications bureau will definitely not do it.

2. If someone has their own route. You just have to wire from it to your home.

3. If there is no route, you give the route to the borrower's house, and connect it to your house.

4. Reset the router first, and then follow the instructions, set your computer to be, and then play on the IE, OK

Then the problem is on your router, 1, after changing the IP, start-run-cmd- ping doesn't work.

No, there's nothing to say.

Through, you see if you changed the IP dns to no. A lot of people ignore and forget.

IE Tools Options Content Clear SSL and try your luck with the system reboot haha.

You can try to reset the router first, remove the external network cable, and then use a wired connection to the laptop, and then type it in the browser, if you can get in, follow the wizard to install.

di504 I've used,This router will be unstable after a long time.,Sometimes it's sometimes you two take turns to try.,It should be okay.,After entering, the username is admin password is not a space or admin,Good luck.。

Why would you want to set up your computer to be?

Whatever, set your computer to automatically get IP and DNS, then factory reset the router, and then access the address written on the back of the router.

Some routers default to Yes.

You have to check the IP range of his router, then set your router to the same, and then set it up!

See if the default IP address is it?

Possibly, it is. If you can't get in again, reset the route, and then log in with the default IP, user, and password to reset it

Don't use the WAN port, just use the route as a switch, and the secondary route is not in your consideration.

How to configure the D-Link wireless router:

1.Connect the wireless router to a higher-level network device (e.g., modem, first-level router).

Connect the WAN port of the router with the LAN port of the higher-level network device with a network cable, and the connection is successful when the WAN port light flashes on the router.

2.Connect your computer wirelessly to your router.

The computer searches for the router's wifi name (the default wifi name is located on the nameplate on the back of the router) and connects to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the wireless gateway configuration page.

Open a browser, enter the IP address of the router gateway (usually, the default value is located on the nameplate on the back of the router) to enter the gateway configuration page. (This interface will pop up automatically for new routes).

4.Set up a wireless router to access the Internet.

Go to the WAN port settings in Advanced settings. If the broadband service requires dial-up, select PPPoE dial-up, otherwise you can choose DHCP to get automatically. To dial up PPPoE, enter the broadband account password, and select Automatic connection as the connection mode.

If DHCP is automatically obtained, you do not need to enter this field.

5.Set the wifi name and wifi password.

Go to Wireless Security in the Wireless Settings and select WPA2-PSK mode for Security Mode. Select AES for WPA encryption rule. Set up a wireless network key.

6.After the setting is completed, the router will automatically restart, please enter the new wifi password to connect, and you can access the network.

To put it simply, first set the computer to IP to automatically obtain, and then connect to the router and must be plugged into the LAN port, then the computer will get the address obtained from the router, or, if it is the former, enter it in IE, if it is the latter, enter it in IE Enter, a login interface will appear, and enter admin or guest in it, depending on the general instructions behind your router. Generally, there is a link wizard, which is an active plug-in, which will tell you the settings step by step, generally only need to enter the username and password, and dial up with the router and it's OK I wish you success.

First find the IP address of the router behind the router, the general IP address is or, if yes, then you set the IP address of your own computer to be, and the subnet mask to be, if yes, then you set the IP address of your own computer to be, and the subnet mask to. After setting up, connect the computer to the router with a network cable, power on the router, and enter the IP address of the router on the browser. This will pop up a dialog box asking you to enter the username and password, which are generally admin and all lowercase.

At this time, you connect the network cable from the mode to the WAN port of the router, and remember that the computer must be connected to the LAN port. There's then a setup wizard - next step - select "ADSL Virtual Dialing (PPPOE)" - enter the username and password you used to dial in the next dialog, save it, and you're done. Now set up the IP address and DNS server on your computer to be automatically attacked, and you don't need to set DHCP on the router anymore, DHCP is turned on by default!

If you want to connect multiple computers, just connect a network cable on the LAN port of the router, and then connect a switch to it.

Hope mine solves your problem.

The default gateway refers to the way you want to access the network, you remove the default gateway, configure the IP at random and connect to the IP of a network segment.

Let's set your IP to get it automatically, then just follow the instructions! Or press your router to factory settings to reset your routers!

Reset is also restricted!! The route is broken, right!!

First of all, make sure that your connection method is correct: the cat - the router WAN port, and the router LAN port - two computers.

If it's not a connection problem and the page of the router can't get in, you can reset the router, there is a hole in the router, take a thin thing in the case of power supply, press and hold the button in the hole for 5 7 seconds and then release it, and then power off and restart, reset the router parameters, so try to do it.

If this doesn't work, brush the version of the router, first go to the latest software version suitable for your router model on the official website of dlink, then go to the tool page of the router, select the version update, restart the router after success, and reset the router.

Steps to set up your router to surf the Internet:

1. Open the router page, log in and open the setup wizard, next step.

2. Choose the way you access the Internet, broadband dial-up, static IP or dynamic IP, the next step.

4. Go to the running status page to see if the WAN port can obtain the public network IP, if the public network IP is obtained, it means that it has been connected to the public network.

There are only two computers in the network, so you can set the local connection of the computer to DHCP to automatically obtain.

Hardware accompaniment method.

With the router alive, press and hold the reset button next to the power jack with a sharp hard object for about 8 seconds.

Software approach. First open the browser, type in the address bar or look at the back of the router that says), then press Enter. Pop up the "Connect to the hand-held Bi Chaoqing dialog box, fill in the username and password.

After logging in to the configuration page, select Tools, select System Settings on the left, and click Restore Settings.

When the prompt box pops up, if you are sure you want to reset all the settings to the factory default state, click OK.