How to wire the start stop controller for vehicles?

The voltage is 24V, and there are five wires in a single plug:

1. The blue plus red line is the power supply + pole to the flameout motor.

2. The black wire is - pole (iron wire) to flameout motor.

3. The blue line is the output of the flame-out motor + the pole line.

to the ignition key.

4. The blue plus white and blue plus yellow lines are controlled by the ignition key switch (+ pole) to control the forward and reverse rotation of the flame-out motor to control the oil circuit of the oil rod to extinguish the flame-out.

Introduce. For new cars (automatic.

The main reason for the stalling is the lack of driving skills, and another possibility is the car engine.

Or the problem of the oil circuit, but for the new car, the problem of the engine itself is less likely, and most of the reason is the problem of the oil circuit.

Finally, for older models, the reason for stalling is not only the lack of driving skills, but also the use of substandard oil to deposit carbon in the engine.

etc.

The voltage is 24V, and there are five wires in a single plug, I will briefly say this. 1.Blue plus red line is the power + pole to the flameout motor 2

The black wire is — pole (hit iron wire) to flameout motor 3The blue line is the output of the flame-out motor + the pole line to the ignition key 4The blue plus white and blue plus yellow wires are used by the ignition key switch (+ pole) to control the forward and reverse rotation of the flame-out motor, so as to control the oil circuit of the oil rod to turn off the flame-out.

Working principle and usage method 1, working principle: the controller is driven by a DC motor, decelerated by a snail gear mechanism, and driven by the connecting rod mechanism and the cable pull plate to drive the diesel engine oil circuit switch and intake valve switch to achieve the purpose of starting and turning off the diesel engine. 2. Line principle and wiring method:

According to the mutual disconnection relationship of each contact of the combination switch key in different positions (as shown in the table, the terminal code in the table is the special point of the controller), the controller wiring is as follows: the controller motor positive --- combination switch 6 contacts (blue) controller flameout line--- combination switch 7 contacts (blue yellow) controller start line--- combination switch 8 contacts (blue white) controller power supply positive --- 24v 12v 15V) Fuse wire--- battery positive (blue) controller, motor negative --- battery negative (tie wire) This is it!

All 5 wires should be added to the relay.

When the power is off, the magnetic field disappears, and the spring tension pushes the extinguishing rod back to the closed oil circuit; Motor refers to an electromagnetic device that converts or transmits electrical energy according to the law of electromagnetic induction.

It is denoted by the letter M in the circuit. Its main function is to generate driving torque, as a power source for electrical appliances or various machinery. Generators are denoted by the letter G in the circuit. Its main role is to utilize electrical energy to convert into mechanical energy.

What effect is it to add a relay??? Is it just a single control to start and stop??? Also, do the 5 wires mentioned have to be added to the relay???

To install a relay, we must first know why we want to install the relay and what effect we want to achieve. The relay is equivalent to a switch, the role is to control the large current with a small current, so that we can protect the operation of the switch.

The 5-wire starting controller you are talking about, first of all, you have to know what kind of wire the wire is, whether it is a power supply or a tie-in; Whether it is the control end or the controlled end, after figuring it out, it is OK to know the port of the relay and the corresponding line of the port.

If you still don't know how to add, then you tell me what the 5 wires are and the type of relay (several ports, whether they are normally open or normally closed), and what are the components you want to control, and what effect you want to achieve (such as in which switch position to start to run, etc.), and I will teach you to add.

The voltage is 24V, and there are five wires in a single plug, I will briefly say this. 1.Blue plus red line is the power + pole to the flameout motor 2

The black wire is — pole (hit iron wire) to flameout motor 3The blue line is the output of the flame-out motor + the pole line to the ignition key 4The blue plus white and blue plus yellow wires are used by the ignition key switch (+ pole) to control the forward and reverse rotation of the flame-out motor, so as to control the oil circuit of the oil rod to turn off the flame-out.

Summary. Hello dear, <>

1. According to the mutual disconnection relationship of each contact of the diesel engine flame-out device in different positions (the terminal point code is the point for the controller) 2. The controller wiring is as follows: the positive stage of the controller motor - the combination switch 6 contacts, the controller flameout line - the combination switch 7 contacts, the controller start line - the combination switch 8 contacts, the positive stage of the power supply of the controller - (24V fuse wire - the positive pole of the battery, the negative pole of the motor of the controller - the negative pole of the battery (lap wire).

How to wire the diesel flameout switch?

Hello dear, <>

1. According to the mutual disconnection relationship of each contact of the diesel engine flame-out device in different positions (the terminal code is the point hall for the controller) 2. The control of the orange car maker is arranged as follows: the positive level of the controller motor - the combination switch 6 contact controller flameout line - the combination switch 7 contact controller start line - the combination switch 8 contact controller power supply positive level - (24V fuse wire - the positive pole of the battery, the negative pole of the controller motor - the negative pole of the battery in the hall (tie wire).

Hello dear, <>

1. According to the mutual disconnection relationship of each contact of the diesel engine flame-breaker in different positions (the terminal point code is the point for the controller). 2. The controller cable guide is as follows: the controller motor is dismantling the jujube hole level - 6 contacts of the combination switch.

Controller flameout line drain - combination switch 7 contacts. Controller start line - combination switch 8 contacts. Positive stage of the power supply of the controller - (24V fuse wire - positive pole of the battery.)

Negative pole of the controller motor - negative pole of the battery (tie wire).

1. The red line is connected to the positive pole of the battery (normal power supply);

2. The ON file of the "green line" connection ignition lock switch;

3. The "black wire" is connected to the negative electrode of the battery (lap iron);

4. The "yellow line" is connected to the start gear or Y gear (preheating gear) of the ignition switch.

The specifics are not clear. If it's the kind of three-wire, you can only connect the power cord without the throttle cord to try it, only turn on and off the car key, and you can try it out without starting the engine. Try it with confidence, it won't burn the ground.

Line principle and wiring method:

According to the mutual disconnection relationship of each contact of the combination switch key in different positions (as shown in the table, the terminal point code in the table is the special point of the controller), the controller cable is as follows:

Controller: motor positive --- combination switch, 6 contacts (blue), controller flameout wire--- combination switch, 7 contacts (blue yellow), controller start line--- combination switch, 8 contacts (blue white), controller power supply positive ---24v, 12v 15v), fuse wire, --- battery positive (blue).

Negative pole of the controller motor - negative pole of the battery (tie wire).

Line principle and wiring method:

According to the mutual disconnection relationship of each contact of the combination switch key in different positions (as shown in the table, the terminal point code in the table is the special point of the controller), the controller cable is as follows:

Controller: motor positive --- combination switch, 6 contacts (blue), controller flameout wire--- combination switch, 7 contacts (blue yellow), controller start line--- combination switch, 8 contacts (blue white), controller power supply positive ---24v, 12v 15v), fuse wire, --- battery positive (blue).

Negative pole of the controller motor - negative pole of the battery (tie wire).