The stone countertop is pasted on the base layer of the woodworking board, which is generally made o

It must be made of marble glue.

Pre-coagulant needs to be added to it.

Please participate in the answer below, hehe, choose one of the two.

Generally speaking, wood and tiles are glued together, and the following methods can be used.

Wood and tiles are glued together, preferably with polyurethane glue for decoration, or epoxy AB glue, or special carpentry nailless glue can also be used. The results are good.

2.Marble glue (that is, the usual marble glue), if you first put nails on the board (the denser the better, the outer leakage head 1mm) the effect is better, which can not only increase the contact surface but also play a role in leveling.

3.Glass glue or structural glue plus double-sided adhesive strip (with sponge in the middle), first use double-sided adhesive strip to dot the brick (play a role in temporary fixation), and put glass glue on the form of dotting a few more, just stick it.

1. The surface of the board is relatively smooth, and the stone is easy to fall off directly on the woodworking board (plate). Paste with glue, glue can be used construction glue, glass glue, etc.

2. Put drilling screws or self-tapping screws on the woodworking board. Leakage 1cm, open a small mouth on the back of the corresponding stone, nail the buckle, fix it with marble glue, and the rest of the back of the stone can be appropriately glued with glass glue or structural glue.

3. First, it is necessary to brush white latex on the two contact surfaces of the two kinds of plates to ensure that the bonding surfaces can be fully bonded; Secondly, it is stopped with straight nails to ensure that the two plates are fully contacted.

4. Moreover, fixing with self-tapping wire will increase its firmness, and the straight nail is basically a temporary fixation, while self-tapping fixing is the secondary fixation after bonding.

It depends on who is outside, different levels of installation methods are different, the woodworking board can be fixed on the stone can be glued, and the stone can also be fixed on the wood with glue, but it depends on the weight of the market.

Use special glue for stone, or woodworking board to hang steel mesh, batch cement mortar, hang stone, it is recommended to use the latter.

Paste with glue, glue can be used construction glue, glass glue.

There is a special glue, or it is fixed with screws.

All horizontal surfaces (except suspended ceilings) can be pasted with glass glue or marble glue; The vertical surface with a height of less than 3.5 meters can be pasted with marble glue, and the structural adhesive used in the building glass curtain wall can be pasted from meters to 7 meters. If it is more than 7 meters, it can be 150cm*150cm on the wooden base layer with 20 round nails, and then use cement mortar to paste it conventionally. The cutting size of the top granular stone (such as granite) must be less than 600cm*600cm, and the wire should be perforated and pasted with structural adhesive; Textured stone (e.g. marble) should not be topped.

The first thing to see is how tall the stone is, how big is the stone, whether it is suspended in the air, and then you have to use glass glue with a few pictures, I can tell you if it is firm.

Marble glue can stick to wooden boards. Marble glue has been recognized by the majority of stone users and the construction industry, and is suitable for bonding between various types of stone or repairing cracks and fractures on the surface of stone, and is often used for repairing, bonding positioning and caulking of various types of stone laying projects and various types of stone.

Marble gum has excellent performance, which is mainly reflected in hardness, toughness, rapid curing, polishability, weather resistance, corrosion resistance, etc.

Due to its water resistance and durability, the general marble glue is not very good, and shrinks when curing, so the building construction code stipulates that marble glue is generally not used as a structural glue, and is often used for rapid positioning or stone repair.

Do you ask if the marble glue can stick the marble on the board, it is completely possible, generally when doing modeling, it is the base layer of the woodworking board first, and then the marble is glued to the woodworking board, as long as the woodworking board ***, it will not fall off.

Marble glue can be glued to the board, because it can only be pasted on the surface of the board, and it cannot follow the cold shrinkage and heat of the board, and the board will fall off after a long time. The nail-free adhesive used in the wooden board can effectively solve the problem of pasting.

No, the planks should be made of latex. If you stick the marble on the wooden board, you can, generally do the modeling, are the first to do the woodworking board base, and then use marble glue to glue the marble on the woodworking board, as long as the woodworking board, it will not fall off, in the actual construction, but also with the use of glass glue, that is, on the back of the stone interval on the glass glue.

Matters added: Marble glue is based on unsaturated polyester resin, which is suitable for bonding between various stones or repairing cracks and fractures on the surface of stones, and is often used for repairing, bonding positioning and caulking of various types of stone paving projects and various stones.

Marble glue is based on unsaturated polyester resin, which is suitable for bonding between various stones or repairing cracks and fractures on the surface of stones, and is often used for repairing, bonding positioning and caulking of various types of stone laying projects and various stones.

And what about sticky boards:

Choose glue: 1. If it is a large area of wood glue that is specially slow-drying; It has a good bonding effect. But the cost of wood board glue is relatively low. The bonding effect is indeed very good, reaching the destructive force of the adhesive surface, and the same is true for small area adhesion.

2. The glue of sticking wood boards is generally used by users of yellow glue, white latex, all-purpose glue, AB glue, the cost is not high, and the effect is quite good.

2. Commonly used curing agent: imported MDI44V, M-200, the ratio is generally 5%-10%.

So it should be sticky and the physical properties are all different.