How to use AVIC control card ZH Um U3 03 04

The control card zh-um is used as follows:

1. Open the software and click on the settings with the mouse.

2. Enter the password in the pop-up dialog box, and a data setting will pop up, and set it according to the size of your screen. If it's a USB flash drive.

Just click on the U disk, if it is a serial port, click half a port to save and close the dialog box.

3. Click on the text, after the text you want is good, the U disk will be plugged into the computer, and the U disk will be saved on the U disk and directly inserted into the U disk interface of the control card. If it is a serial port, it is over by directly sending the program, indicating that you must correspond to your control card model when setting, such as um to select um, u0 to select u0, otherwise it will prompt that the control card model does not match.

Control card zh-um how to use.

Control the software, you open the software, there is a setting on it, click on the setting with the mouse, talk about a dialog box to ask for a password, after you enter the correct password, there is a data setting pop up, you will set it according to the size of your screen, if it is a U disk, click on the U disk, if it is a serial port, click half a port to save and close the dialog box, and then click on the text, after the text you want to be good, the U disk will be plugged into the computer, Click on the U disk to save your good text on the U disk and insert it directly into the U disk interface of the control card, if it is a serial port, directly click to send the program and it's over, explain that you must correspond to your control card model when setting, such as um on the um, u0 on the u0 on the line, otherwise it will prompt the control card model does not match.

Control the software, you open the software, there is a setting on it, click on the setting with the mouse, talk about a dialog box asking for a password, after you enter the correct password, there will be a data setting pop up, you will set it according to the size of your screen.

If it's a U disk, click on the U disk, if it's a serial port, click half a port to save and close the dialog box, and then click on the text, after the text you want to be good, the U disk will be plugged into the computer, and the U disk will save your good text on the U disk and insert it directly into the U disk interface of the control card, if it is a serial port, directly click to send the program and it's over, explain that you must correspond to your control card model when setting, such as um to choose um, u0 to choose u0, otherwise it will prompt the control card model does not match.

The solar photovoltaic grid-connected power generation system consists of photovoltaic modules, grid-connected inverters, metering devices and power distribution systems.

Solar energy is converted into DC power through photovoltaic modules, and then converted into sine wave current at the same frequency and phase as the grid through a grid-connected inverter, so that green and clean solar energy can efficiently serve human beings.

To use the same model, because it is AVIC we have a proposed control card such is quite useful.

An inverted image, and an inverted real image. It is often said that the fear will be great.

AVIC's control software, you open the software, there is a setting on it, click on the settings with the mouse, talk about a dialog box asking for a password, after you enter the correct password, there will be a data setting pop up, you will set it according to the size of your screen, if it is a USB flash drive, click on the USB flash drive, if it is a serial port, click half a port to save and close the dialog box.

Then click on the text, after the text you want is good, the U disk will be plugged into the computer, and the U disk will be saved on the U disk and directly inserted into the U disk interface of the control card, if it is a serial port, directly click to send the program is over, explain that you must correspond to your control card model when setting, such as um on the um, u0 on the u0 on the line, otherwise it will prompt the control card model does not match.

LED Display: A flat panel display that consists of small panels of LED modules.

LED, Light Emitting Diode (Light Emitting Diode abbreviation). It is a kind of semiconductor light-emitting diode display mode, which is made of gallium (Ga) and arsenic (As), phosphorus (P), nitrogen (N), indium (In) compounds, when electrons and holes are recombined, it can emit visible light, so it can be used to make light-emitting diodes. It can be used as an indicator light in circuits and instruments, or as a text or digital display.

Gallium arsenide diodes glow red, gallium phosphide diodes glow green, silicon carbide diodes glow yellow, and indium gallium nitrogen diodes glow blue.

AVIC's control software, you open the software, there is a setting on it, click on the setting with the mouse, talk about a dialog box asking for a password, after you enter the correct password, there will be a data setting pop up, you will set it according to the size of your screen, if it is a trillion U disk, click on the U disk, if it is a serial port, click half a port to save and close the dialog box.

Then click on the text,After the text you want to be good,U disk will be plugged into the computer,Click U disk to save your good text on the U disk and insert it directly into the U disk interface of the control card,If it is a serial port,Directly click to send the repentance program is over,Explain that you must correspond to your control card model when setting,For example, um will choose um,U0 will choose u0,Otherwise, it will prompt that the control card model does not match。

LED Display: A flat panel display that consists of small panels of LED modules.

LED, Light Emitting Diode (Light Emitting Diode abbreviation). It is a kind of display mode of semiconductor light-emitting diode, which is made of gallium (Ga) and arsenic (As), phosphorus (P), nitrogen (N), indium (In) compounds, and can emit visible light when electrons and hole complex groups are eliminated, so it can be used to make light-emitting diodes. It can be used as an indicator light in circuits and instruments, or as a text or digital display.

Gallium arsenide diodes glow red, gallium phosphide diodes glow green, silicon carbide diodes glow yellow, and indium gallium nitrogen diodes glow blue.

The screen setting password is 168, or directly Ctrl+S to open it directly.

First of all, choose the right model, and the width is the number of display width points to be carried. (Number of unit boards * Number of points of a board), the height is the same.

The wiring method is selected according to the display to be carried. Generally regular P10, regular indoors. For details, please ask the ** business.

If the screen is blurred, please change the OE polarity and data polarity, and try it in the case of blurred screen.

The color mode is the color of the screen, and you can choose single-color, two-color, and three-color according to the situation of the unit board. Conventional P10 generally does not need to be modified.

If you use a serial port, you can use the serial port to send data. The number of serial ports (COM ports) needs to be selected by yourself, if one is directly selected, if there are more than one, please determine as follows. (Right-click on My Computer -> Management -> Device Manager -> Port.)

Plug in the serial port cable, and you will see a COM port appear. Select this com port.

The screen setup is almost complete. Specifically, you can also refer to the manual or call the technical support ** number. The numbers are written on the manual.

Open the AVIC control software, click on the setting to select the screen setting input 168 to enter the display setting window and select the model zh-u2, according to your screen point input and screen parameters, etc., save and close the page, what do you not understand, you can also consult Technetium Optoelectronics!

AVIC control, you open, there is a setting on it, click on the setting with the mouse, talk about a dialog box to ask for a password, after you enter the correct password, there is a data setting pop up, you will set it according to the size of your screen, if it is a U disk, click on the U disk, if it is a serial port, click half a port to save and close the dialog box, and then click on the text, after the text you want to be, the U disk will be plugged into the computer, Click on the U disk to save your good text on the U disk and insert it directly into the U disk interface of the control card, if it is a serial port, directly click to send the program and it's over, explain that you must correspond to your control card model when setting, such as um on the um, u0 on the u0 on the line, otherwise it will prompt the control card model does not match.