How do I use the transparent stickers inside the MG GUNPLA OOQ?

1.Wipe the surface of the model with a damp cloth 2Cut out the outline with a pen knife along the pattern or text of the sticker (this point is easy to be overlooked, in order to prevent errors in the manufacture of water stickers, some blank edges will be left, these blank spaces are best removed), soak in warm water for about 10 seconds, then take it out and put it aside for a few seconds.

3.Use your fingers or tweezers to move slightly to determine whether the water sticker has been separated from the paper base, and then put the water sticker and the paper base on the surface of the model to be pasted, gently press and hold the water paste with your fingers, and then use the tweezers to remove the paper base. Allow the water sticker to remain naturally on the surface of the model.

4.Use tweezers to adjust the water paste to the correct position. Use a cotton swab to gently squeeze out excess water and air bubbles from the middle to the sides.

5.If it is a more complex surface, you can apply some water paste softener to the surface of the water sticker, wait for about 15 seconds, and then repeat the extrusion step with a cotton swab. By the way, take care of the surrounding area of the drain sticker and make sure that there is no extra glue and cotton wool and you're done.

That's a water sticker, right? Cut it off first, soak it in warm water for two minutes, gently move it off with your fingers and paste it, and if possible, you can apply another layer of softener. I'm talking about water sticker usage, you see what sticker that's first.

It may be a scraping sticker, don't get dirty at the bottom, look at the last page of the manual, follow the sticker above, draw it down with a pen knife, press it to the specified place, and then scrape it with your fingernails.

, ask sprinkle directly, he is your number know-it-all.

It's called a hanging sticker. Cut off the part to be pasted first, be careful not to cut the pattern badly, it is recommended to use a pen knife or blade. Then fix it with tape, if it is sprayed paint, be careful not to use transparent tape, because the strong adsorption force is easy to damage the paint surface.

Then use something a little sharper, such as a toothpick, to move back and forth on the tape to allow the sticker to attach to the surface of the model. Finally, tear off the tape, here be careful not to tear it all at once, but to tear it little by little, to see if it is completely pasted, if not, re-attach it and scrape it back and forth with a toothpick. Of course, it should be noted that if it is domestic, the quality of the hanging sticker is not very good.

The sticker and the bottom paper can be separated non-destructively, there is no dividing line on the sticker and the sticker is thick and not easy to bend, from the reverse side of the separated sticker, the image on the sticker is more blurry is the scratch paste (transfer sticker), the usage is the same as the above. If the bottom paper is colored and can not be separated non-destructively, there is a dividing line is a water paste, cut the corresponding part and soak it in water, until the bottom paper is taken off, it is pasted on the model after being dipped with a cotton swab, and it can be air-dried after adjusting the position.

That one is a hot pressed tape, first you have to buy a thinner transparent tape, and then occupy the side without protective paper, pay attention to leave a little tape outside, and then stick it to the model and press it for 3 to 5 minutes. Pay attention not to touch it after printing, or it will fall off.

That's scraping, first cut off the one to be pasted, then put it in the place to be pasted, fix it with covering tape, scrape it all to the place to paste with something similar to the tip of a ballpoint pen, and it is best to spray a layer of matte paint.

That's pad paper.,Good thing.。

Cut the pattern first, preferably to cut the offset to be about the same size as the pattern.

Then put it in the place where you want to stick it and fix it.

Press the pattern vigorously with an object such as a cotton swab.

Until the pattern is completely glued to the model, it is enough to remove the offset plate such as Sinanju verKa, there are a lot of these pad stickers, I'll show you the renderings. I made Sinanju.

PS: That's the effect of applying varnish. There is no varnish that kind of gloss, my phone pixel is not good, may not be able to see clearly)

Cut off the one to be pasted, press the back side (rough side) on the place to be pasted, press, gently scrape the smooth side with your hand until the place without the picture is no longer translucent, gently and carefully remove it slowly, and it is OK.

The water sticker is soaked in water, pressed on the model for a while, and it sticks to it, you can also tear it off by hand and stick it on with water.

That's a water sticker, please.

There are also the first two, don't mislead others by talking nonsense if you don't understand.

The water sticker is to cut it off and soak it in water, and then paste it on until it reaches a place you are satisfied with, and then a cotton swab will dry it and it will stick.

2l is right.

First of all, I would like to point out that most of the MG Gunpla models are sent scrapers and stickers, and what the landlord said should be scratch stickers. It's easy to use:

1.Cut out the part you want to paste.

2.Place the cut sticker on the rough side as the bottom surface and fix it with tape around the edges.

3.Use a hard object (cap, tip of tweezers, etc.) to gently scrape the other side of the sticker until the white part of the sticker is no longer transparent.

4.Carefully remove the tape.

Don't mislead people, 2l is right. If it's hard pasted, it's a scratch sticker.。。

You can search the Internet for water stickers, a lot of tutorials, but you don't have to use water to paste the purified water of the softener.

Hello! The white one is called a pressure sticker, which can generally be called a transfer sticker, and the usage is like the previous kind of tattoo sticker, just cut carefully, and then paste it on the model (you can dip it in a little water), fix it with scotch tape, squeeze it moderately through the end of the pen knife or fingernail, scrape it gently, and finally peel off the transparent glue and film together (pay attention to light), and the pattern on the transfer paste will be transferred to the model; The light blue one is a water sticker: the water sticker can be called a water transfer sticker, which also needs to be cut out, and then soaked in warm water (it doesn't take a lot of water, the time can't be too long, the general pattern is almost separated from the paper), and then use tweezers to stick the side with the pattern on the model and fix it (ps:

Squeeze the air in the water sticker back and forth with a cotton swab and absorb the excess water to prevent air from entering the water sticker), the water sticker generally only appears in the white ka version of the model, and it is difficult to deal with it, but the effect is very good and not easy to drop, the above are my experience of the two stickers. Finally, there are two other types of stickers for GUNPLA, one is a metallic sticker attached to transparent parts such as eyes, and the other is a very common transparent sticker, which is usually a pale yellow background and can be used directly! Hope the above helps!!

The attached sticker is obviously a hanging sticker, cut it out, fixed it with tape, and then scrape it with your fingers or pen until the pattern is printed on the model, and then tear it off.

First of all!!

Scrap stickers should never be soaked in water!!

Be sure to apply a transparent sticker first, then a scratch sticker, and then a water sticker!!

You can use scissors to scrape the part to be pasted, and then put it on the part to be pasted, fix it with transparent glue, and then use a fingernail or other tools to scrape it evenly, and remove the plastic sheet and transparent tape to complete.

The water sticker is also used to cut off the part to be pasted with scissors, hold it with tweezers and put it in the water for 3 seconds, take it out and put the water sticker next to the target part, and then use a wet brush to gently dial the pattern on the water sticker to the target part (just like slowly pouring tofu from one plate on another plate). After that, cover it with a paper towel (you can come out in one layer) and press the surrounding area with your hands, and blow the hot air through the paper towel at the pattern position for 10 seconds. (The water sticker is easy to fall off, so please confirm that you have purchased a protective paint before deciding to paste it, and it is best to leave it for more than a day before spraying the paint, so as to reduce the occurrence of blistering).

If the water sticker is troublesome, cut out the pattern to be pasted, soak it in warm water for 3-5 minutes, then take it out and cover it on the model, scrape it with tweezers or a small stick, and print the straight pattern on the model.

The watermark sticker can be separated by water, and then carefully moved to the model to wait for dryness, pressure sticker, that is, the scraping sticker is to fix it on the part to be pasted and then scrape it several times to paste it.

The watermark paste is to cut out the pattern to be pasted first, soak it in water for about 10 seconds, and then take it out, the water is carefully sucked off, it will be separated, and then put it in the place to be pasted, and then use a special solvent to make it melt off, and it is best to spray a layer of matting paint, because the water paste is easy to scratch.

The pressure tape is to cut the pattern first, then cover the place to be pasted (pay attention to the front and back), and then scrape the surface repeatedly a few times, and it will separate.

The translucent half is only sent at the level above MG, and the HG half only has metal stickers (thick stickers, ordinary stickers) Gunpla now has 5 kinds of stickers Ordinary stickers (all kinds are sent, the most common stickers) The parts used: generally the eyes, restore the color with advantages: with a little metallic luster Disadvantages:

Too thick Transparent stickers used parts: signs, warnings, etc., are usually very small advantages: good stickiness, thinner than ordinary stickers, scratch-resistant than transfer stickers and water stickers (more ideal stickers for the Su group) Disadvantages, although it is transparent, but up close still feel that there are some excess parts (you can cut off the excess parts when pasting to solve) The parts used in the transfer sticker:

Signs, warnings and other advantages: the film is very thin, good-looking disadvantages: easy to scratch, pay attention when pasting, do not let the sticker peel off before pasting.

The parts used in the water sticker: signs, warnings and other advantages: thin film (basically very no sticker), good-looking disadvantages:

There are many tools to be used, and the difficulty of pasting is relatively higher than the previous ones, so use more tools Gold foil stickers (a new type of stickers recently adopted in RG) Parts: power pipes, "metal" parts, etc.Advantages: It can make the place where it is pasted look like metal, and the operation is simple Disadvantages: unknown.

There are generally 3 types of stickers that come with the model. Ordinary stickers, attached to the eyes and other parts, this sticker is used less and is opaque. Adhesive sticker, transparent, relatively large amount, mainly used for some small decorations, can be played freely.

Pad paste, transparent, the amount is also relatively large, can also be called scratch paste, and it is more common to use. Translucent only pad stickers and adhesive stickers, and the models come with them, which can be assured. Another thing to mention is the water sticker, all GUNPLA models don't come with their own water sticker, you need to buy it yourself, Taobao has it, domestic Nissan has it, you can choose it yourself, this is also translucent.

There are generally three kinds of translucent stickers for models: 1 general adhesive sticker, 2 transfer stickers, 3 water stickers, and the first two are generally attached, and the third type needs to be purchased separately.

Bandai's only water stickers, transfer stickers (scratch stickers), adhesive stickers, three kinds, there is no watermark sticker, MG most of the standard transfer stickers and stickers, a few special will bring water stickers (such as the new card version of the manatee), the transfer paste white transparent bottom surface has a layer of cotton paper to protect the sticker in the process of transportation will not be scratched, the way to use is to cut the required pattern, remove the cotton paper, cover the original cotton paper protective surface to the model, fix it to the desired position with paper cover tape, and then use hard objects, such as nails to scratch on the surface, The pattern will be detached from the transparent paper and stamped onto the model, adhesive sticker, the same as ordinary sticker, remove the part that needs to be directly pasted.

Water sticker, also cut out the required pattern, soak in warm water for 3 seconds, put it on the model and slowly pull out the bottom paper with a cotton swab, the upper layer of the pattern will be separated from the paper and cover the model, and then continue to adjust the position of the water sticker with a cotton swab, and squeeze out the excess water after it is in place.

That means you need a water adhesive, and the domestic bubble pig seems to be ten pieces a piece.

A: Hello, this is a kind of sticker composed of some different colored powders, and now I will list how to use it for you.

The first step is to cut out the direction of the sticker you want to use.

The second step is to press it on the Gundam that you want to affix to it.

location. In the third step, slowly scrape off the sticker with your fingernails or the tip of the round-tipped scissors.

Fourth, slowly remove the transparent paper that makes up the sticker.

That way, your Gundam will have this sticker on it, and I'm glad to serve you, whether you pick me up or not.

It's basically all said downstairs. Note that when this thing is printed on the model, the sticker must not be misplaced. Move the pattern a little and the pattern will tear. Be careful.

Transfer the sticker, stick it where you want it, and scrape it vigorously.

This kind of scratch post. Use scissors to cut out the parts you need to use, wipe the surface of the model parts clean, and never have water or dust. Place the cut scraper in the place where it needs to be taped and fix it with tape, and then carefully scrape it with your fingers or other relatively blunt objects.

When you see that the color of the pattern has completely lightened, carefully remove the tape. It is best to spray a layer of matte paint or gloss paint as a protection after pasting.

Scrap paste, cut off the pattern, and wipe the place to be pasted, use transparent glue to glue the scrape sticker, and then scrape it evenly back and forth with a hard object. After a few back and forth, you can tear off the transparent glue. The pattern is on the model.

The adhesive sticker is directly removed and pasted on.

Cut out the transfer sticker yourself, and then fix it in the place where you want to paste it, and then scrape it on the sticker with a hard object a few times to print it, and then remove the transparent paper.

The water sticker should be soaked in water before it can be applied.

You seem to be a transfer sticker, the back of the paste itself is not sticky, you have to cut it with scissors, and then put it in the position to be pasted, preferably with a covering tape, and then use a nail or something to scratch and scratch it, and finally take off the surface.