How does Telecom E8 B router ZTE achieve Wifi settings?

Hello, first of all, thank you for your support to China Telecom. According to your description, the device is China Telecom Broadband Cat not a router, China Telecom Broadband Cat is not able to directly access the Internet wirelessly, it needs to be cracked before it can be, but after cracking, it may cause your network to be unstable and ITV can not be used normally, you only need to buy a router, connect and set up according to the instructions for use to access the Internet wirelessly. If you need to check the bill and pay the phone bill, please log in to the online business hall of Anhui Telecom.

Have a great day! Hope mine is helpful to you and can get yours!

Dear Telecom users, Hello! First of all, thank you for your support to China Telecom, according to your description: since there is no query about the setting method of ZTE route, it is recommended that you can call 10000 or contact 800010000 QQ customer service, let the staff answer for you.

Telecom wifi coverage, that is to say, there are still some areas without this network signal! In addition, in some remote places, the signal strength is not very large! You could be in one of these two situations!

You check or call customer service to inquire whether there is wifi signal coverage in your place! If you have, you can buy wifi duration, the first thing you have to do is that your network card device can detect and connect to the wifi signal! Hope it helps.

1.The computer browser opens "This is the login interface for the wireless cat settings, account: telecomadmin password: ne7ja%5m (this messy account password is the telecom administrator, you can copy and paste the past, pay attention to the number of digits)

2.After entering the wireless modem settings interface, select "Network - Broadband Settings". Take note of the VPI and VCI values in the middle of this interface.

3.After the connection name is a drop-down menu, select them one by one, and click "Delete" at the bottom of the screen to delete the drop-down menu.

4.Select "New WAN Connection" after the connection name, then fill in your broadband account (** with area code) and password at the bottom of the interface, and other settings do not need to be changed (VPI and VCI should be the same as those in the second step), and finally click "Create" at the bottom.

Setup, please skip this step if you don't have ITV. Continue to "Create WAN Connection", select "LAN 2" (that is, ITV port) for the binding option, select "Bridge" for the mode, click on the drop-down menu for "VPI VCI", select the previous step, and finally click "Create" below.

6.On the wireless modem settings page, select Network - DHCP Configuration, and enable the DHCP service checkmark (default).

7.Wireless cat settings interface, select "Network - WLAN configuration", change the name and password of WiFi (no problem if you don't change it, but the default is not easy to remember.)

8.On the Wireless modem settings page, select "Management - Device Management" and "Restart". (There is a "factory reset" below, for help).

9.Delete the "Dial-up Connection" on the computer and fill in the IP &DNS to access the Internet.

10.After connecting to wifi on your mobile phone, you can access the Internet without PPPOE.

Use your account password.

Username: telecomadmin

Passcode: ne7ja%5m

Note: The password is more complicated, it is recommended to copy and paste it).

1. Enter the back interface.

2.Open Network - Broadband Settings.

3.Find your local VPI VCI connection in the connection name.

4.Select your local VPI after the VCI connection. dot Delete Connection.

Note that deleting your local VPI VCI will not be able to dial in with a computer after the connection. Deleting this connection is to lay the foundation for setting up the route below) 5.After deleting the connection.

A new connection is made. Bearer service Internet (Enabled) mode Route (PPPoE) Use NAT to enter your account password to access the Internet, OK.

6.Management --- device management--- device reboot (routing setup complete.) 7.The following steps start configuring the DHCP service, which allows you to limit the IP address to control the number of computers connected to the Internet.

8.Wireless network settings, if you don't use wireless, you can disable it here, so far the settings are basically completed, I hope my answer will help you, more questions can be logged in to Hubei 10000 to know.

Generally, the configuration of the E8 wireless router is as follows (if it is a wired router, please ignore the steps of the wireless setting):

0) If it is ADSL access, prepare two network cables, one network cable to connect the computer network port to the LAN port of the router, and the other to connect the LAN port of the cat to the WAN port of the router (the computer network cable is connected to the router in order to configure the router, if you use wireless, after configuration, you can unplug it).

1) The router is powered on, and the cat is powered on.

2) Find the router's instruction manual.

3) Find the management IP of the router (generally, the login account password (such as the admin password is empty), and log in**Example->

Different models and different brands of routers will be different)

4) Statically set the IP address of the computer host and the management IP in the same network segment (if the router is enabled by DHCP function by default, then set the computer network card to automatically obtain the IP).

5) Log in to the wireless router management interface.

6) Turn on the DCHP service of the wireless router.

7) The wireless router is set up with PPPoe auto-dialing function to connect permanently.

8) Turn on the wireless function of the no-friction line router, and set the wireless Internet password (if it is a wireless router, the password is set to be complicated to prevent it from being cracked).

9) The IP and DNS of the mobile network are set to be obtained automatically.

This should be able to automatically dial up the Internet, wired and wireless at the same time.

PS: If the router is enabled DHCP by default, then the IP and DNS of the computer should be set to automatically obtain, so that if multiple computers form a LAN, there is no need to set the IP.

If you don't know your username and password, you can ask customer service.

If you have any questions, please contact us.

Good luck, hehe.

The Epon E8C terminal is mainly set up with the following steps:

First, if Senbu and E8C terminals are connected to optical fibers, the "optical signal" light should be extinguished, and E8C uses LOID and its uplink OLT for registration, and establishes an EPON system after registration.

Step 2: Log in to the device with the username: "telecomadmin" and password: "ne7ja%5m".

Step 3: Configure the routing mode

1. Enter the "Network" - "Broadband Settings" function;

2. Put a checkmark in the box before "2 Internet B vid", and change the "bridging" of "connection type" to routing;

3. After the "connection type" is changed to "route" mode, the relevant information box will automatically pop up, and in the "user name" and "password" fields, enter the user's ADSL dial-up broadband (such as password (*need to remind the user: if you change the broadband or change the password and other telecommunication services, you need to log in here to make corresponding modifications);

4. After the setting is completed, press the "Apply" button to realize the routing function, and the terminal will display "Processing";

5. After the setting is successful, the terminal will pop back to the broadband setting interface, and the Internet channel will be displayed as the routing mode.

Step 4: The user's computer searches for the WIFI signal of the SSID of the Oak Grip, and connects to it to access the Internet wirelessly (the WIFI password can be viewed on the bottom tab of the E8-C terminal, or logged in to the terminal management interface "Network" - "WLAN Configuration" to view (*Tips: The WiFi password is also changed here).

The preparation is not difficult. There are 3 things we need to do.

1.Back up the original data. Don't expect to back up the parameters on your router by typing in some strange address, as advertised on the Internet.

It's useless, especially for the new models that are now out, and Telecom has long blocked these functions. What we can do now is to take a pen and take a notebook (ask for a notebook, don't just pull a piece of paper, it will be lost), and then log in to the router as a useradmin (the password is on the sticker on the back of the router), and then copy it down.

What parameters do you need to copy? Actually, there are two places:

One is to copy down the software version number of the router, which you need to refer to before upgrading in the future. And I believe that in the near future, there will definitely be new cracked patches on the Internet for new versions of routers. The software version should be as close as possible, otherwise it is easy to break.

The one below is the version number, and the one above is the one to be selected next).

This picture is definitely different from the picture above, you should have more connections here than mine, at least two or three connection channels. One of them may start with TR069, but there must be an Internet one. Those IP addresses do not need to be copied, please copy down the titles of all connections, i.e.:

Internet R 8 35, pppoe this kind of information is copied down.

2.The second step is to prepare for the upgrade.

google, keyword: h608bfix

This patch is only over 900k, which is short and concise.

3.Ready to upgrade the patch, still can't. Because...

Because the upgrade patch you get is likely to be an expired version That is to say, because the upgrade patch is in the process of upgrading, it is found that your router is not a user in the jurisdiction of that telecom company, or the software version number is incorrect, the "update configuration" button in it will turn gray and will not let you press it! So, the third preparation, that is, the ability of lyra, to use the little Dongdong who is only 9k in the "Lyra Tools Encyclopedia" to activate the expert. I still won't provide this in the blog, you also just need to google, the keyword is "activation expert", you can find the latest version of the potato line, or green!

It should be noted that this tool will be judged as "malware" by firewalls such as the new version of Rising because it can force the gray buttons to light up. However, this is definitely not a virus, so you can safely press "Allow**". Excerpt from.

Give you a picture of my house for your reference.