The interior door should be equipped with a set of wires, and one side should be left with three bra

Indoor doors and windows are also a landscape of the home, many people choose trapezoidal sets when choosing door sets, so how to install it! Step 1: Measure the size of the door opening and determine the opening direction according to the stairway.

The size of the door opening should be larger than the size of the installed door, and leave a certain margin (approximately, convenient for debugging and correction during installation. Step 2: Correct the door opening, the size of the door opening does not meet the requirements must be cut and leveled with iron gongs, steel chisels, cutting machines and other tools to meet the installation requirements.

Step 3: Put the door into the door hole during installation, plug it tightly with wooden bolts around it, correct the horizontal and vertical degrees, debug whether it is open flexibly, then open the door leaf, drill the installation holes through the door frame installation hole with an electric hammer, and fasten them with expansion bolts one by one. The depth of the expansion bolt into the wall should be 5cm, and the drill bit of the impact hammer should match the size of the expansion bolt.

During the installation of the project, the owner or the builder shall mark the 50cm horizontal line or 100cm horizontal line, and the user shall determine the height of the floor tiles or floor for individual installation. After the door is installed, a certain amount of cement mortar needs to be poured into both sides of the door frame (generally more than 70%).

Of course it's thick good! The 3 cm door sleeve line is heavier than the 2 cm one, and it is not easy to deform. Manufacturers often make thick ones thin for the sake of profits.

2 options. 1Instead of a door sleeve on one side of the wall, install the other two sides.

2 door set custom-made.

Most of the door sleeves are 5 cm, so at least 6 cm must be reserved to install the door cover, and the middle of the door sleeve needs to be marked with foaming agent to insulate the sound, etc., only 3 cm is not enough; If you don't make a door sleeve and choose to install a finished door sleeve, you can reserve 3 cm.

In layman's terms, the door cover is the two frames inside and outside the door, so it is also called the door frame. The main function of the door sleeve is to fix the door leaf and protect the corner of the wall, so the space for the reserved door sleeve should be as large as possible.

With the door sleeve, the door sleeve line is naturally indispensable, the door sleeve mainly plays the role of fixing the door leaf and protecting the corner of the wall, and can also decorate the door, and the door sleeve line is often said to be the door "line".

If only 3 cm is reserved, it is not enough to make a door cover. The door sleeve is the door inside and outside the door two door frames, its main role is to protect the wall, and to fix the door leaf, so when reserved, we should try to be careless, so as to leave room for it. Generally speaking, it is necessary to leave 5 cm, or even 6 cm, to meet the needs of installing the door cover.

When it comes to door covers, I believe everyone is more familiar with them, and now most users will consider installing door sets when choosing door leaves, which can not only prevent the door from being bumped and scratched, but also make the door look more beautiful. However, some friends don't know much about the installation details of the door cover, so is it enough to reserve 3 cm for the door cover?

1. Reserving 3 cm for door sleeves is generally not enough.

2. However, depending on the specific situation, most of the door sleeves are usually 5 cm in size, and the foaming agent needs to be beaten in the middle of the door sleeve during installation. It is recommended to reserve a distance of 6-8 cm for door covers. However, if you choose a finished door cover, it is okay to reserve 3 cm.

3. When the door sleeve is installed, the surface of the door leaf should be cleaned first, so as to facilitate the connection between the door sleeve and the corner, and the nail should be nailed to the recess of the ** strip. In addition, it is best to install a door suction device on the door cover against the wall in the living room to avoid scratching the wall or door edge when the door is opened with force.

The above is the introduction of whether it is enough to reserve 3 cm for the door cover, I hope to help netizens.

For many people, the door cover is very unfamiliar, as a term in the architectural decoration has not been heard by many people, but basically everyone knows what it is, the door cover is the two frames inside and outside the door, so it is also called the door frame, which has the effect of fixing the door leaf and protecting the corner of the wall, and can also be decorated, so is it enough to reserve 3 cm for the door cover? What are the common door cover materials? Let's follow the experts of Qeeka Home to understand Cong Xiaoming.

1. Is it enough to reserve 3 cm for the door cover?

Reserving 3 cm is not enough to make a door cover, because most of the door sets are 5 cm, at least 6 cm must be reserved to install the door cover, and the middle of the door cover also needs to be covered with foaming agent to sound insulation, etc., only 3 cm is not enough; If you don't make a door sleeve and choose to install a finished door sleeve, you can reserve 3 cm.

2. What are the common door sleeve materials?

1. Marble door casing.

Marble door cover has a very good decoration, and it is also relatively expensive, suitable for high-end home decoration, with elegant and dignified performance, and easy to clean, wear-resistant surface, easy to clean, and is loved by many owners.

2. UV paint section veneer door cover.

UV paint finish door cover is a new type of material, made of multi-layer board, the appearance of the use of UV paint technology, showing a more vivid color, and not easy to crack, deformation, in moisture-proof, heat-proof, wear-resistant also has a good performance, the key is long service life, environmental protection.

3. Steel door cover.

The steel door is suitable for matching the steel door sleeve, other materials may not be able to bear its weight, the use of the same substrate is a better choice, the choice of steel plate is shaped, the surface is processed in the transfer paint technology, there is better decoration and long service life, generally used more on the entrance door, very strong.

Summary: The above is about reserving 3 cm to make a door sleeve is enough, and what are the common door sleeve materials, I hope the content shared can give you some reference, if you want to know more about relevant knowledge, you can **** Qijia Home to consult.

1.Is the door sleeve reserved for 3cm or 4cm?

The reserved door cover is not 3cm or 4cm, but 5-8cm. The door sleeve is mainly to cover the gap between the wall and the door sleeve, and play the role of decoration and protection. When installing the door cover, you need to put styrofoam in the middle of the door cover, which can make the door cover more beautiful.