Pioneer recorder buy 218 or 217 or 118 or 117

It depends on your motherboard interface,I made a mistake last time I wrote a single by myself,I wrote 117,The result is not to change to 217,You better check the interface of your motherboard first,Then choose the paired optical drive。

Model DVR-217CH

Inside, outside, built-in.

Burner type ***+ -rw

Interface type SATA 150

Model 218VXL

Inside, outside, built-in.

Burner type ***+ -rw

Interface type SATA 150

Model DVR-117CH

Inside, outside, built-in.

Burner type ***+ -rw

Interface Type IDE

Model DVR-118CHV

Inside, outside, built-in.

Burner type ***+ -rw

Interface Type IDE

It is recommended that you choose the 7-word ending, and the interface of the motherboard can be seen by the optimization master.

217, 218 is basically the same as 217, of course it is cheaper to buy. The current motherboard generally only gives 1 IDE port, and some don't even give it, and 117 is not suitable for new users.

Series 2 is a SATA interface, and Series 1 is an IDE interface. If you are newly installed, it is recommended to use the 2 series, so that the case is much cleaner, which is good for both wiring and heat dissipation.

The 218 is different from the 217 only the front panel.

Now, of course, it is to buy 218, and the cost performance is the highest.

The 2 series is a SATA interface, and the 18th is the evolution of the 17th generation, in fact, there are not many improvements, and SATA's chassis wiring is more convenient.

Buy 217, I'm using it, it's good, it's OK, it's easy to install and disassemble the serial port.

This mainly depends on what you do with it, and now 118 and 218 are out, ** and 117 217 are the same.

The 118 series with the light engraving function ** is still the same as the 117 series The function has also been improved Buy 118.

117 is not easy to buy.

There is a 118 figure on the market, but I don't see the 218 series.

It can be burned, but the format must be converted and engraved before it can be put in

1All DVR-118CHV is PATA's parallel port, that is, the cable, 218CHV is PATA's serial port, which is a small data line, the difference between the two is the way of the interface, SATA's transmission rate is higher than PATA, the current mainstream interface of the motherboard is more biased towards SATA's, and the PATA interface will be gradually eliminated in the future, and the upgrade convenience mentioned on the 3rd floor also means that the motherboard will not have PATA's interface in the future. If you want to upgrade to a new motherboard, then there is no place for your PATA optical drive, so choose a 218 machine with SATA interface.

One is the parallel port and the other is the serial port, which is the difference, and the serial port wiring is relatively convenient

It should be determined according to whether the motherboard supports serial port and the ** required by the user, DVR118CHV is an IDE interface that is slightly cheaper than the serial port 218CHV.

218 is the SATA port, that is, the serial port. 118 is the IDE port, that is, the parallel port. Other functional features are the same, it is recommended to choose 218, although it is more than 10 yuan expensive, it is still worth upgrading in the future.

The interface is not working, 218 is a SATA interface, and 118 is an IDE interface.

Use the first one to compare the hot ones and the sales are good.

It's normal that the back of the pioneer is with an anti-counterfeiting sticker, and you scratch the sticker to enter the anti-counterfeiting code inside the quality inspection.

PS: Your realistic 218L is normal.

The difference displayed in the device manager may also be caused by other problems such as data cables, so the anti-counterfeiting label on the back of the machine should prevail.

That's right. Mine is also 118chv showing 118l. China is the display 118L. It's normal. If you show 118chv, it means that your Pioneer recorder is fake.

When did you buy it? It's best to take a look at the picture 118 is to support ladeifiash It feels like yours is not really in the pioneer recorder that is, behind the pioneer recorder is the anti-counterfeiting sticker There is a code in the China Quality Inspection Association** can be found or hit the pioneer of the 400 to tell them the serial number to check it.

It's obviously a fake, last time I remember who asked, go and return it.

118chv is to support flash carving It is recommended that the landlord figure out what model he is buying In addition, flash carving also needs to be supported by a burning disk.

You can also test the optical drive, generally in "Other" - Get System Information "You can view the performance of the optical drive, the performance of the optical disc. This burning software is very good.,The landlord is about to install the OEM's nero8,It's not an incomplete version.,It's not as good as my cracked version aboveN7.。

There is no burning software, which may be a JS problem, and each machine has a random software gift. You can find js to ask for... In addition, the burning error,It may be caused by the low version of the software you are using now.,It is recommended to use the software sent randomly.。。。

In addition, the power cord bayonet is tighter.,That's your power port is new.,I haven't used it.,So it's definitely tight.。。。

Pioneer's 117ch is indeed a fake, you can refer to this post to tell for yourself whether your one is genuine or not, good luck!

The Pioneer is not a good machine, and the poor compatibility of the reading disk is not good, so it is not surprising that the disk that is currently reduced in price and quality has flown off.

It is recommended that you change to LG or Jianxing to engrave.

If you insist on carving, it is recommended that you change to other disks, or reduce the speed of carving, recommend 6 speed carving, the current quality of Weibao is not ordinarily rotten.

In your case, the speed of burning with nero is greater than the double speed on the platter, generally using 8x, and you burn at 12x speed, and the probability of failure is very high. There is also a need to consider the power supply, when the power supply is insufficient, it is easy to be engraved, I use the pioneer one, and it is the old model 111, and the burned platter is really uncountable

1.Find a regular seller.

2.There is an anti-counterfeiting sticker on the back of the machine, and there is an anti-counterfeiting code inside, and the code can be found in the industrial and commercial ** or SMS is genuine.

3.Consult the customer service technician.

I haven't heard of it, but I've heard that there is a price in memory.

Most of the write errors are caused by the quality of the disc or the aging of the bald head, it is recommended to upgrade to the latest quantile and then replace the platter and computer to try.

The first is the aging of the recorder, and the second is the software conflict.