Kneel and beg! Press F1 30 to turn on the machine

Restore or optimize BIOS settings.

After turning on the computer or restarting the computer, "CD...... is displayed on the screen, press the "DEL" key to enter the BIOS settings interface, award

Load BIOS defaults, this option is used to load the BIOS initial settings to determine the scope of the failure.

Load Oprimum Settings, which are optimized settings for the factory BIOS.

or AML Load BIOS Setup Defaults, which is used to load the initial BIOS settings.

Load High Performance Defaults, which is used to load BIOS optimization settings.

After selecting the default or optimized value with the keyboard arrow keys, press the Esc key, F10 key, and Y key to save and exit the settings.

2. Turn off the floppy drive.

Reboot, press Del into the BIOS, find the Standard CMOS Setup, press Enter in the open interface, change Drive to None (Off), press ESC, F10, Y, save and exit the settings.

3. Set the hard disk as the first boot. Reboot, press del to enter the BIOS, find the Advanced BIOS Features (advanced BIOS parameter settings), press enter to enter the Advanced BIOS Features interface, and set the First Boot Device to HDD-O (hard disk boot). Press ESC, F10, Y, save and exit settings.

4. Do not enable the check function of the floppy drive.

Reboot, press Del into the BIOS, find the Advanced BIOS Setup, press Enter, and in the interface that opens, boot up Floppy Seek, set to "Disabled". Press ESC, F10, Y, save and exit settings.

5. Check and replace the motherboard battery.

Enter the bols. Change the motherboard settings to default. If not, turn off the computer. Then take the battery off. Then turn it on. If it's okay, just put the battery back on.

Mine too? Find the answer and tell me, thank you!

1. Restore or optimize BIOS settings.

After turning on the computer or restarting the computer, "CD...... is displayed on the screen, press the "DEL" key to enter the BIOS settings interface, award

loadbios

defaults, this option is used to load the BIOS initial settings to determine the scope of the failure.

loadoprimum

Settings (load motherboard BIOS factory settings), which are optimized settings for the factory BIOS.

or amlload

biossetup

defaults, which is used to load the initial BIOS settings.

loadhigh

performance

defaults (high performance default), this option is used to load BIOS optimization settings.

After selecting a default or optimized value with the keyboard arrow keys, press the ESC key, F10 key, Y key, press Enter, Save and exit the setting.

2. Turn off the floppy drive.

Reboot, press del into the BIOS, and find Standard

cmossetup, press enter in the interface that opens, and then drive

A: and DriveB: both change to none, set Floopy to Disable, press ESC, F10, Y, press Enter, Save and exit the settings.

3. Set the hard disk as the first boot. Reboot, press del into the BIOS, and find Advanced

For BIOSFEATURES, press Enter to Advanced

The biosfeatures interface will be first

bootdevice

Set to HDD-O (Hard Disk Boot), press ESC, F10, Y, Enter, Save and Exit settings.

Go to the BIOS settings at boot time and restore the BIOS default settings, and you should be fine.

Three possible causes of this:

1。Your computer has a floppy drive, which will be caused by the first boot time if it is set to a floppy drive, and the time will be set to the initial state after booting.

It's very inconvenient, just turn off the floppy drive, (the following will talk about the method of off) because there is a USB flash drive now, and the floppy drive is basically not used.

2。You unplug the console after shutting it down, so that's how it goes. Just don't pull it out next time. It's okay not to pull it out.3 The BIOS coin cell battery on the motherboard is dead.

There is no way, only to change the battery.

How to turn off the floppy drive: Reboot, press del into the BIOS, and use the arrow keys to select "Standard".

cmossetup, press enter, enter "standard."

CMOSSettup. In the "standard

CMOSSettup" interface, use the arrow keys to select the selected "DriveA", and use PGUP or PGDN to turn the page"to "none".

Press esc, press f10, press y, save exit.

Relatively simple and practical method).

You can try. I wish you a speedy solution.

Replace the battery on the motherboard.

After the change, press the del key continuously when turning on, and go to the first item of the BIOS to see if there is anything to change to none

f10 save exit.