How to use a router without Modu, how to use a router

Router setup steps Connect the computer network card with the LAN port of the router with a network cable and turn on the power of the router; Double-click the IE browser on the computer, enter the IP address of the default setting page of the router in the address bar, and press Enter; Enter the default username: admin, and the default password:

admin；Click OK. Click Setup Wizard in the left rail, click Next; Click on ADSL Virtual Dialing (PPPoE) and click Next; Enter the broadband, password, and click Next; Click Done. Many friends think that the setting is over here, but in fact, there is still one point that has not been completed.

Because the following settings are not completed, many friends encounter 691 errors in dialing, or can connect to the network, but it will be dropped after a short time. Let's continue the settings: click the MAC address clone menu in the network parameters menu on the left sidebar, click Clone MAC address in the interface that appears, and click Save.

At this point, the router will prompt you to restart the router, click OK to restart the router. After the router restarts, close the Internet Explorer. Connect the WAN port of the router with an incoming network cable, and then connect the computer to the LAN port of the router with a network cable to start surfing the Internet. Note: "Some users have multiple computers at home, but don't know the MAC address of which computer to clone.

You only need to directly connect the cat (or home network cable) to the computer with a network cable, and then dial on the computer, which computer can dial up the Internet, and clone the MAC address of which computer. These processes are done and absolutely ready to use.

You have to recite a mantra. Please refer to the manual for details.

Step 4 If it is a TP Link router.

First, plug in the wires from the cat, plug into the WAN port of the router, and then 3 wires come out of the router. Plug them into your computer separately.

Second, set the parameters of the router and enter it in IE Generally, the back of the router has this IP. There is a point enter.

Third, open the router's setup wizard. Go to the next step, select PPPoe and then prompt you to enter your account number and password, you enter your home broadband account number and password, and then proceed to the next step. Click Done.

Step 4 Find the third setting of the router, find the WAN port settings, and select Autoconnect below. Restart the router and you're good to go.

Yes! With the router, you can use multiple computers to access the Internet, the smallest router has 4 ports, and the large one has 8 16 ports. Now it is recommended that you use the wireless router directly, which also comes with 4 ports. It's very convenient to wait for your computer to be upgraded and used,** and it's pretty much the same.

2.Set up the router, connect the power supply, connect well, open the web page and enter the IP address in the address bar, generally see the manual).

3.Enter your username and password (as shown in the manual).

4.Go to the setup wizard and follow the steps to fill in your broadband username and password.

5.Once you've completed the settings, you'll be able to surf the Internet. (The IP can be automatically obtained).

6.router, you can also set which one can access the Internet and which one can't, limit the traffic, and you can explore it yourself when you have time.

Yes, you can use a router to connect 3 desktop computers at home at the same time, and the router has a separate non-side-by-side hole that is plugged into the broadband cable that is plugged into your home, and the other is plugged into the computer.

Routers have a manual, just do it according to the manual, TPLink router is the most convenient.

Yes, if it doesn't work, read the manual, it's very clear!

Are the two routers of the same brand?

Use a laptop to build a wifi hotspot, there are many tutorials on the Internet;

Without a router, there is no wifi signal, how can your mobile phone be linked.

You can connect it with your laptop's WiFi hotspot.

DNS server addresses, if there are misconfigurations in between, all can be set to be obtained automatically. The second factor is that the **server is enabled in the IE settings, and the address filled in is wrong or has expired, and cannot be used.

Plug the router up, call ** to the network operator and ask them to turn on multi-person Internet access, and then dial up to access the Internet!

If the router can only connect to one computer, then connect another switch to the router. The computers are connected to the switch.

The router dials, and the others are connected.

Then you dial directly with the route, and the four computers will pass the route.

Change to a router with better routing performance, and check whether the router has port rate limiting or QoS and other settings turned on.

First of all, check whether the network cable is normal, two network cables for connection, and replace the network cable connecting the router and the computer to the cat and the computer directly.

Huaxia Alliance.

Step 1: Use one network cable to connect the modem (broadband modem) and the router WAN port, and use another network cable to connect the router LAN port to the computer network card interface. Step 2:

Open the browser, enter the router login address, enter the login username and password of the router in the pop-up window, and enter the broadband account and password according to the setup wizard. Step 3: Click [Wireless Settings] in the router settings interface, set the name and password of the wireless network, and then search for the set wireless name through the computer to connect.