ADSL: How to share the Internet without a router for two machines, that master helps

If the network operator does not allow dual network cards to share the Internet, one network card will be prohibited.

If you don't want to buy a router, you can get a soft route, it's a lot, this is a free version, I haven't used it, you can research it yourself.

The two machines should be connected with a cross wire.

If you don't have a router, you can't do it! Unless you have two usernames for adsl!

In this way, when B goes online, A has to turn on the computer, and at the same time, A also has to install shared Internet software, which is very troublesome, and I did it with the company N years ago. Now the route is only 7 or 8 ten, and you can drag it to four. With automatic dialing of routes, A, B, C, and D can all surf the Internet independently.

We generally use a direct network cable, but now most network cards can be connected with a direct network cable.

Sharing the Internet is very simple, a do the hosting, dial up, and then turn on the online neighbor right-click on the properties Advanced below.

Internet connection The following hooks can be hooked, and it will set the address of the intranet network card and the IP address of host B to the mask gateway.

That's it.

Choose me the best I'm in the same situation as you, take a closer look.

Don't connect anything yet.

Wireless router settings for dial-up Internet access.

1.Disconnect the dial-up network gracefully.

2.Connect your wireless router to your computer. This step can be connected wirelessly, and the wireless connection has no password by default.

Or the LAN port of the router and the network port of the computer are wired. If you are not a new router, it is recommended to reset the route (usually there is a small hidden button on the router, press and hold it for 10 seconds. Refer to the router manual).

3.Go to the wireless router settings page through your computer's browser (usually or refer to the router body or manual). Administrative passwords may be required, also refer to the instructions.

4.Set the WAN port to PPPoE dial-up connection, and enter the account and password provided by China Telecom. Set the wireless network name and password.

5.Connect the modem (modem) and the router WAN port, if it is a network cable to the home, you don't need to go through the modem.

6.The computer can be wired or wirelessly connected to the router to access the Internet wirelessly. Desktops or laptops need to be set up to automatically obtain IP addresses.

It's simple: you don't have to make it that complicated:

Your problem is that the computer connected via a network cable can access the Internet, while the computer connected via a wireless network card cannot access the Internet

According to your description, there are only two ways to solve it:

1. The wireless Internet access settings of your router are not enabled, please enter Enable 2. Your routing wireless encryption method is incorrect, please change it to WPA WPA2-PSK encryption mode.

Okay, so after checking the above two points, you're ready to go online.

You see if the computer you use the wireless network card has obtained the IP, whether you have filled in the IP address but not the DNS address. If you don't know your network's DNS, change it to automatically get the IP and DNS. If it's win7, adjust ipv4.

Besides, if there are any wireless restrictions in the router, you can only find them yourself.

It's not easy to ask how two computers are going to be shared. In short, you turn on both guest users and set up sharing.

There are also slight differences in the adjustment of the system, you can also go to the Internet to find it, there are many teachings to share.

Turn the router upside down, there is an IP address and account password on the back, open the web page, enter the IP address, set a good password for broadband, turn on the wireless network, enter the wireless network password, OK, and you can go online.

First, set the local connection of the host to shared, the last bit of the IP of the secondary machine is different from the host's, you set the IP address of the host in the second column below the address. I hope that the picture in QQ will make you learn faster, 1481463676

How can multiple computers use one account to access the Internet through China Mobile WLAN? Dual network cards are installed on a computer, two network cards are installed, and one network card is connected to the network and shared is set. The other network card is connected to the other computer.

Use network cables to directly connect 2 computers to form a peer-to-peer network, and one of them sets up a ** server.

As long as your ADSL cat is a single LAN port and does not have wireless function, it is not possible to achieve two computers to access the Internet at the same time without any configuration!

Connect two computers The desktop must be connected to the network Then there are only two ways for the laptop to connect to the desktop Either the desktop dual network card, with an extra network interface to connect the laptop with a network cable Or the desktop installs a wireless transmitter as a hotspot, and the notebook connects to the desktop wirelessly The desktop as a hotspot needs to connect the transmitter There is something like a USB flash drive.

But I think these two methods are redundant Buy an extra network card to get 100 transmitters also have to dozens It's better to buy a router to worry, and wait for two computers to connect on the OK But two computers at the same time log in to an account seems unrealistic, only one can be a host and one as an extension serial Internet.

Let's go up first** and give a perceptual understanding. Below the router is a LAN computer.

The WAN port of the router must also be connected to the cat.

The general wireless router configuration is as follows (if it is a wired router, please ignore the steps of wireless settings):

0) If it is ADSL access, prepare two network cables, one network cable to connect the computer network port to the LAN port of the router, and the other to connect the LAN port of the cat to the WAN port of the router (the computer network cable is connected to the router in order to configure the router, if you use wireless, after configuration, you can unplug it).

1) The router is powered on, and the cat is powered on.

2) Find the router's manual.

3) Find the management IP of the router (generally tp-link is, d-link is, login account password (e.g. tp-link is admin and admin password is empty), login ** example - >

4) Statically set the IP address of the computer host and the management IP in the same network segment (if the router is enabled by DHCP function by default, then set the computer network card to automatically obtain the IP).

5) Log in to the wireless router management interface.

6) Turn on the DCHP service of the wireless router.

7) The wireless router is set up with PPPoe auto-dialing function to connect permanently.

8) Turn on the wireless function of the wireless router and set the wireless Internet password (if it is a wireless router, the password setting is complicated).

This should be able to automatically dial up the Internet, wired and wireless at the same time.

PS: If the router is enabled DHCP by default, then the IP and DNS of the computer should be set to automatically obtain, so that if multiple computers form a LAN, there is no need to set the IP.

If you have any questions, please contact us.

Good luck, hehe.

The router must first log in according to the IP address (usually secret: admin) and set it according to the wizard. Finally, clone your computer's MAC to the router, save and reboot.

There is no problem with the line connection, but is the router configured?

Does your router have automatic dialing, otherwise you won't be able to access the Internet. And whether the router is set up on the following computers, you need to set up an IP to access the Internet.

Connect the ADSL box network cable to the input connected to the router, then connect your computer and another computer network to the output port of the router, use your computer to open the IP address of the router and then set it up. It's OK to go online directly without dialing up every day!

Enter the router in the address bar. The password and account number are generally admin, there is a setup wizard, always click on it, you select ppo sdal to surf the Internet, fill in the adsl username and password, and it's OK

Two PCs choose to get the IP automatically!

The above IP and account passwords are not fixed, and there are instructions in the general router manual.

Is there any routing configured?

Here's how to set it up in detail.

If you've already set it up but still can't access the internet.

Ping the route first to see if it can work.

If that doesn't work, reset the route and set it up again.

There is also a place where you can put the IP configuration manually

No, you can q me.

You need to install a router so that multiple computers share a single network cable.

You need to set the autodialing option in the route pppoe+dhcp

If you don't set the route, you can see if the account and password in the route are incorrect.

If you use a router and have to dial the number, it means that you have not set up the router.

2. Enter the account and password of the router (not the Internet account and password), generally the default account and password are admin, please also check the nameplate at the bottom of the router for details.

3. Click the setting wizard, fill in the pppoe in the way of surfing the Internet, click on the next step for the rest, and then there will be an interface that requires you to fill in the Internet account and password, fill it in truthfully, close the browser and exit the router settings, if the router asks you if you want to save the modification when you exit, click "Yes".

In this way, it should be possible for the two to surf the Internet together, and the router that is set up does not need to be dialed.

You should find a copy of the router's manual to read, or go directly to the Internet to search for the router configuration of that model, and someone will explain it to you in detail. In general, using a router is to input the dial-up information, it will do it for you automatically, and it can be shared by multiple computers. If you have to dial up with routing, you must not have done it right.

If you use a router, don't dial up, see what brand your router is, enter the corresponding address in the address bar, generally the back of the router is available, and then the user enters the username and password, generally admin, after entering, just set up your broadband account and password, don't dial with the router.

You're going to have two lines on the route, so that the other one doesn't have any internet at all, it's easy to do, you don't buy a router, you haven't bought it, or you've already bought it, and you're asking me or chatting privately.

To connect two computers at the same time, you'll also need a router. You get the router first.

Plug the network cable on the computer you have the Internet to the LAN port of the router, and then plug the two network cables into the LAN port and connect them to the two computers respectively. You can ask questions.

Check with elimination:

Use computer A to access the Internet alone without going through the router:

1. If A can access the Internet, it may be a router problem (or a network cable connected to the router).

2. No, use the computer B test.

1) Line B, indicating that there may be a problem with A.

2) B doesn't work, modem or line problem.

Also: if you've tried to connect your computer with the backup modem "alone" (which is important), you can focus on checking your line that is associated with the modem and the router.

If you still can't find the reason, you can only find a network service provider.

When you don't go through the router, dial up the Internet 678 means that there is a problem with the external network line, and 691 is a problem with the account password, which should be your router is not good, and it will crash for a long time.

For this kind of service provider's problem, call ** consultation.

Dizzy, definitely not, the Internet says that some software can be realized, if you believe it, you can try it.