It stops when it is turned on, is it a problem with the hard disk? How to solve it? The data is impo

Judging from the prompt, it is the hard disk that has a problem, which means that the hard disk self-monitoring, analysis and reporting system) data is wrong. You first check whether the hard disk interface is loose, or change to a new hard disk.

。Monitoring technology determines that your hard drive has early signs of failure, and it is recommended to back up your data and replace the drive immediately. It is advisable to do so. This technology is still relatively reliable, first back up the data, change the hard disk. Go elsewhere to test your drive.

Did you touch it when you turned it on"tab"key, if you click "esc" or "f2" to select the startup item, you can do it! Disclaimer: If it's not right, don't spray, you can ignore me!

Because I'm in the same situation as yours, but yours and I are not exactly the same! So just wanted to see if I could help you!

The hard drive is damaged, unplug the hard drive and try it.

If you have a problem with the main hard drive, it is recommended to change the hard drive.

This is a problem with the hard drive, I repair the computer, change the hard drive.

Prompt hard drive error Check the hard drive.

Hard drives often disappear for no reason for the following reasons:

1. The hard disk data cable is not in good contact, or the plug has an oxide layer and dust;

2. The power supply plug of the hard disk is not firmly plugged in;

3. The power supply of the host is insufficient, especially the power supply powered by the 20pin plug.

In addition to doing the conventional hard disk cable, hard disk circuit and other checks, the more important but often overlooked, is the power problem, if you do the routine inspection after no results, you should be able to think of the power supply problem, change a power supply to try or hang the hard disk to other normal use of the computer, if it is normal, it means that there is a problem with the power supply or hard disk, replace it.

1. Check whether the hard disk cable is in good contact.

2. Try to change the hard disk interface of the motherboard.

3. This situation has nothing to do with the power supply.

When this happens, it means:

1.The computer's internal hard drive slot is in poor contact or is about to be damaged.

2.The hard drive interface is in poor contact or the hard drive is about to be damaged.

For the first case, you should go to the after-sales service in time to do a comprehensive inspection of the computer. During the warranty period, licensed goods that are not damaged by human damage can be replaced with a new machine (some brands do not need an invoice to warrant), and the warranty is usually recalculated for one year.

In the second case, you should try again with a different hard drive. After the replacement of the computer, the hard disk is persistently displayed, and the assumption is true.

No. If the hard disk cannot be found, you can enter the BIOS interface.

First of all, make sure that you don't recognize your hard drive when you power it up. This can be found in the BIOS. If there is a short sound of the boot drop, it proves that the POST is okay (excluding hardware problems, but excluding the hard disk is not recognized).

At this point, press the DEL key to enter the BIOS and see if your hard drive recognizes it. If you recognize it, the hard disk and data cable are fine, skip the following to see 2. If you are unfortunate enough not to recognize it, it is more troublesome, and there are several situations that can be distinguished.

If the hard drive is broken, if this is the case, no matter how hard you try, it is useless, you can only replace it with a new one. Test method: Hang it on another machine to see if it can be recognized.

If you can't recognize it, it's probably broken. Problems with data cable and jumper settings. a.

The optical drive and the hard disk are attached to the same data cable, and the jumper is the main one. Solution: Plug and unplug different data cables from the optical drive and hard disk.

In this way, the hardware is not easy to conflict, and there is no need to worry about jumper problems. b.The data cable is plugged in incorrectly and incorrectly.

No, the hard disk is damaged, the self-test can not see the hard disk information, and then when it comes to the boot system, it will prompt that there is no boot system. Stay in the BIOS settings interface, there may be a BIOS setting information change, you can reset the settings to save, if this is often the case, it may be that the motherboard's coin cell battery is out of power.

According to your description, there may be several problems.

1. Problems with the operating system. If this problem occurs, the only way to do this is to reinstall the system.

2. Caused by viruses. Use anti-virus software to scan.

3. If there is a hardware problem, the memory is loose or conflicting, you can try to plug and unplug it again. If you're using two RAMs, try them one by one. See if there's a problem.

Because I used a computer that would automatically restart when I used it, and then checked that the two memories were not the same model, so the memory conflicts caused frequent automatic restarts. It may not even start. A similar possibility can occur if the graphics card is loose.

In short, loose hardware connectors or dust will cause the computer to start abnormally. So you can use the substitution method to detect each piece of hardware. Faulty hardware can only be replaced.

Your hard disk may be in poor contact with the data cable and power cable, plug it in from the new one, if it doesn't work, listen carefully to the hard disk when you turn it on, whether there are some abnormal sounds (not the sound of reading or writing the disk) when you turn it on, and if so, it may be a bad sector or a problem with the head assembly (SSD skipping. It is recommended to back up your personal data when you can enter the system, and then test and repair the hard disk, so that even if the hard disk really has to be sent to the professional maintenance department, it is not distressed, after all, the data is backed up, isn't it?

Big brother, change the power supply, caused by insufficient power, there is no other problem, and the hard disk has no bad sectors

Is the data cable or power cable of the hard drive loose? Or is the hard drive broken?

There is too much junk in the system and it gets stuck.

You use the HD Tune Pro hard drive detection tool to test the hard drive, check the speed and health, and scan it again to see if there are any bad sectors! Don't use a quick scan when scanning!

Fault phenomenon.

The motherboard configuration of the computer is MSI 815E Pro, and the hard disk is IBM 20G. After the computer is booted up at one time, the screen displays: "Disk boot fallure, insert system disk and press enter", put it into the system floppy disk according to the prompt information, and after the floppy disk is successfully booted, type "C:"

After pressing the enter key, you can't enter the hard disk.

Turn off the power, open the chassis, check that the hard disk cable is in good contact with the IDE slot, and reboot the computer, and the screen still displays the original fault information. Press the RESET key to start the machine, press the DEL key to enter the CMOS settings main menu (Award BIOS), select the "IDF HDD Auto Detection" bar, and the hard disk will be automatically detected, but the hard disk cannot be detected. After multiple cold boots, enter the CMOS settings for automatic disk detection, but the disk cannot be detected.

Failure analysis and handling.

Phenomenally, the hard disk may be damaged, but the hard disk has been scanned during recent use and no corrupted sectors have been found, and the possibility of complete damage is not very high, and the last shutdown before it fails to boot is to exit according to the normal procedure.

Detach the hard disk and connect it to another machine, enter the CMOS settings main menu after booting up, select the "IDE HDD Auto Detection" column, detect the hard disk parameters, and enter the hard disk normally. Install the hard disk back on the original machine, and after entering the CMOS settings, the parameters of the hard disk can be automatically detected, and the normal boot is resumed.

1) The hard drive cable is in contact with the IDE slot and is loose.

2) The hard drive is indeed damaged.

3) The hard disk head does not return to the boot position when the power is turned off, and the hard disk parameters cannot be detected by using the automatic disk detection function in the CMOS settings. At this time, the hard disk can be removed and installed on another machine, and the parameters of the hard disk can be automatically detected by using the automatic detection function of the hard disk by different motherboards, so as to restore the hard disk head to the boot position, and then install it back on the original machine, so as to resume normal boot.