What s the deal with a fully automatic washing machine that stops after a while?

The fully automatic washing machine stops after a while, and there may be the following situations:

1) The washing machine panel door is not closed well or the switch of the top cover is damaged, it may also be that the switch is in poor contact, the washing machine is not allowed to open the top cover because it is a high-speed action when dehydrating, so there is a linkage switch on the top cover, and the cover circuit will be automatically disconnected as soon as the cover circuit is opened. If it is damaged, it will not move.

2) The drainage system of the washing machine is blocked or the drain valve is broken, the washing liquid in the water cylinder cannot be discharged, or there is too much foam in the water cylinder, the washing liquid in the cylinder is difficult to drain for a while, the water level switch cannot be reset, and the washing machine cannot enter the dehydration program.

3) The drain valve does not open the clutch conversion, and the washing and dewatering of the automatic washing machine are completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally.

4) Poor motor performance and capacitance problems, resulting in insufficient output power, can be solved by replacing the capacitor. The fully automatic washing machine stopped washing in a few minutes.

5) The fastening screws of the inner barrel of the washing machine are loose, or the bottom bracket of the inner barrel of the washing machine is damaged. If this is the case, in most cases, an empty washing machine can be dehydrated.

6) The washing and dewatering of the fully automatic automatic washing machine is completed by the gear at the bottom of the solenoid valve conversion, and the damage of the solenoid valve will also make the dehydration unable to operate normally.

1. First of all, check whether the drain valve core is stuck in the power-off stateYou can see if the spool rod is in place, otherwise the internal spring may be stuckAt this time, the valve cover should be unscrewed, and the foreign object should be replaced if it is stuck or damaged.

2. If the drain valve is normalCheck whether the drawbar of the tractor is in place, whether the drawbar is flexible to pull and return by hand, if there is a stuck, it means that the inside of the tractor has been damaged and should be replaced.

3. If the tractor is normalWhether the retractor has also been activated in the state of water inlet after powering on, shaking the drain valve core for drainage, this indicates that the computer board program has been disordered, and the computer board should be replaced.

How to use a fully automatic washing machine.

1. Plug in the power plug, put down or connect the drain pipe, turn on the tap water, put the clothes to be washed, laundry detergent and additives (softener, bleach, etc.) into the washing machine, and close the cover.

2. Press the power switch, select the water level according to the amount of laundry to be washed, and select the program according to the specific conditions such as the dirty stroke and material of the laundry.

3. Press the "Start Pause" button and the washing machine will start working.

4. After the selected program is finished, the buzzer will beep.

5. After the work, turn off the power switch, pull the power plug out of the socket, close the tap faucet, then open the cover, take out the laundry, clean the wire chip filter bag, and wipe the washing machine dry.

2. It may be that the washing machine is not placed in a ventilated place, or the ventilation hole is blocked, and there is no way to dissipate the heat at this time.

3. When the voltage is too high or too low, there may be a phenomenon of stopping after washing, and it is necessary to wait for the voltage to be normal before use.

My automatic washing machine goes out after two seconds of starting?

The reason and treatment method for the automatic washing machine to start and turn a few times:

1. When the washing machine is washing clothes, if the motor has a humming sound, but does not turn, it may be a problem with the starting capacitor. If there is no sound from the motor, it may be that the lid linkage switch of the dehydration bucket is faulty.

2. Check whether the belt is loose, check the pawl and clutch, and see if the brake is tight or whether the mechanism piece on the drum cover is broken.

3. The automatic washing machine does not rotate, and some motors with clutches may be very hot, and the starting capacitor may be broken, or the wire head will fall off and the motor will not start. If there is no clutch, see if the motor is stuck, do not idle the belt under the motor experiment, whether it is stuck, if it is not stuck, most of the starting capacitors are problematic.

Hello dear, the washing machine has been rotating for the following reasons: 1. The general situation is that the valve core of the water inlet valve is stuck, and it cannot be reset after being turned on by power, resulting in water inlet all the time, and the water inlet valve is replaced first; 2. If the fault is not solved, the problem lies in the water level switch, after a long period of use, the water level switch can stop the water ingress, causing the water inlet not to stop, at this time the water level switch should be replaced. 3. If the pressure pipe is worn and broken due to a long period of use, or the pressure pipe is in poor contact with the water level switch and the outer barrel air nozzle, causing air leakage, it can also lead to more than water ingress.

4. Due to the use of a long time, there is a foreign object blocking the air valve mouth, resulting in the pressure can not be transmitted to the pressure switch, at this time the big nut should be unscrewed, and then take out the inner barrel to take out the foreign body blocking the air valve. 5. If everything is invalid, you should try to replace the computer board, because all the actions are controlled by the computer board.

Summary. Hello, dear The washing machine has been rotating in the following situations: 1. Time setting problem: If the user sets the running time of the washing machine for a very long time, it will inevitably cause the washing machine to be washed all the time. This is where you should check the program settings.

2. The water level sensor is abnormal: If the water level sensor inside the washing machine is abnormal, it will not be able to sense the water level height inside the washing machine normally, and it will always default that there is still water inside the washing machine, so that the drain valve will always be in the drain working state, resulting in the washing machine not stopping. At this point, the water level sensor should be replaced with a new one.

What's the deal with the washing machine that keeps spinning?

Hello, dear The washing machine has been rotating in the following situations: 1. Time setting problem: If the user sets the running time of the washing machine for a very long time, it will inevitably cause the washing machine to be washed all the time.

This is where you should check the program settings. 2. The water level sensor is abnormal: If the water level sensor inside the washing machine is abnormal, it will not be able to sense the water level height inside the washing machine normally, and it will always default that there is still water inside the washing machine, so that the drain valve will always be in the drain working state, resulting in the washing machine not stopping.

At this point, the water level sensor should be replaced with a new one.

What should I do if the laundry keeps turning.

3. Damaged computer board: If the computer board of the washing machine is damaged, it will also cause the washing machine to be washed all the time. At this time, the computer board should be repaired or replaced by a professional.

4. Too little clothes: In the construction of the washing machine, if there are too few clothes inside the washing machine, it will also cause the washing machine to keep washing. At this time, you should stop using the washing machine and put more clothes in it.

Dear, if you keep turning in operation, you can turn off the power, first understand that there is a problem with us before using yo At the same time, remind you to pay attention to safety <>

1. It may be because there are too many clothes, and the motor of the washing machine is overloaded and causes heating, and when it reaches a certain calorific value, the washing machine will stop working. Solution: Don't panic when you encounter this situation, turn off the power of the washing machine, take out some clothes, reduce the load of the washing machine, and then cool down with the motor for ten minutes, and then reconnect the power supply and start washing.

2. The washing machine may overheat and pause due to poor heat dissipation. Solution: In this case, you should first cut off the power supply of the washing machine, and then see if the ventilation hole of the washing machine is blocked, if it is blocked by debris, clean it up, and wait for the washing machine to cool down and then put it back into use.

3. It may be because the line voltage is unstable, the voltage is too high or too low, which may cause the washing machine to pause. Solution: Check the line voltage, if the voltage is unstable, you can install a voltage regulator.

Check if the lid of the dehydration bucket is not properly covered, because the washing machine has a protective function, and if the lid of the dehydration bucket is not properly covered, the washing machine will not start the dehydration function.

The safety switch on the top cover of the washing machine is damaged. The process of dewatering the washing machine is a mechanical movement that operates at high speed. Try not to open the top cover during the dehydration process to avoid damage to the top linkage switch, if the top cover linkage switch of the washing machine is damaged, the washing machine can not be dehydrated.

If the brake is not released, the motor cannot be started due to too much load, and the buzzing sound can be heard at this time, and the drain valve lever can be adjusted.

When there are too many clothes, the washing can not be adjusted to the balance, then the washing machine will automatically adjust to a low speed to cause poor dehydration effect, if this is the reason that the washing machine can not be dehydrated, then do not worry too much: you can put the number of clothes less before washing the clothes, do not stuff too much at once, so as not to cause imbalance during washing and affect the dehydration effect.

Too much washing. When there is too much laundry, the washing machine automatically adjusts to a low speed or simply does not turn anymore. In most cases, there is no need to panic, take out a part of the laundry, and the Royalstar washing machine will work again.

Check if it is the reason for the residue filter, the residue filter is used to filter the residual garbage from washing, we have to clean it frequently, if it is not cleaned for a long time, it will cause the machine to not drain properly and dehydrate.

Clutch problem, water level switch can not be reset.

Repairs or replacements are required. The washing machine dehydration process starts with the water level switch reset after the washing liquid has been drained. If the drain level switch is damaged, dewatering is a procedure that needs to be carried out after draining, and if the water level switch is damaged, the dewatering procedure will not be entered.

Solution: Contact the after-sales point.

Problems with the computer board, usually need to be replaced. In addition, when dehydrating, the garment is tilted to one side and the dehydration procedure cannot continue.

The washing machine drain system is clogged. When the drainage system of the washing machine is blocked, the washing liquid in the water cylinder can not be discharged, when there is too much foam in the water cylinder, or the washing liquid in the cylinder is difficult to drain for a while, the water level switch can not be reset, and the washing machine cannot enter the dehydration program. At this time, the drain filter should be removed for cleaning, and the drain should be flushed with water and the debris in the drain valve should be removed.

The dehydration motor does not rotate and the safety switch contacts should be checked. The current safety protection of household appliances is good, and it should be a problem in terms of contacts. Check whether the plug of the washing machine is loose, the plug is loose and it is easy to lose power, and after the power is off, it will naturally not be able to dehydrate, for this case, it is OK to replace the socket used by the suitable special washing machine and refrigerator.

caused by the texture of the clothing. Compared with summer, there are many types of clothes in winter, such as tweed type of clothes with strong water absorption, if you choose low-speed dehydration, it will cause the illusion that the washing machine can not be dehydrated, so it is recommended to use high-speed dehydration for washing products with strong water absorption performance (PS: high-end clothes can not be used for high-speed dehydration).

If it keeps turning, it should be that the power cord is broken, or the button is broken, and it is about 50 yuan to ask a master to repair it.

1. When the washing machine is dehydrated, check it first to see if there is water in the washing machine, and if there is water, you can open the drain valve first to see if there are foreign objects inside. Method: To disconnect the power supply, you can first open the front baffle of the washing machine and unscrew the drain valve in the lower right corner to drain the water.

Generally, the computer board of the washing machine will show a "5e" fault if there is no drainage**, if there is a foreign object, install the drain valve switch after taking it out, and the test machine should be normal.

It was sent wrong. Hello, the reason for washing is that there is an excessive amount of clothes in the washing machine, and too many clothes will cause a lot of pressure on the washing machine, resulting in the overheating of the washing machine, because the electric heater itself has a protective device, and the electric heater will be disconnected immediately when it is overheated, and the washing machine will stop working, but after a while, the motor will cool down, and the washing machine will start to wash again, and then the washing machine will not stop washing, so the clothes should be put in moderation.

The voltage is unstable, which will also cause the washing machine to wash non-stop.

This is due to the fact that the washing method of artificial intelligence is turned on.

The initial rotation is to allow the probe to fully sense the dirtiness, weight, material and other parameters of the clothes in the bucket, so as to better select the corresponding optimal washing program.