Emmilon maintenance address, Shenzhen Emmilon maintenance

Watch maintenance and repair can refer to 702, Xidan Joy City Office Building, Xicheng District, Beijing

7th Floor, West Joy City Office Building, No. 131 Xibei Street, Xicheng District, Beijing] will answer for you.

1) When wearing a watch, the sweat on the hands is corrosive to the case, the all-steel case is better corrosion resistance because it is nickel-chromium alloy, and the semi-steel case is copper, which is in contact with sweat for a long time, and is easy to corrode, so you should often wipe off the sweat with a soft cloth or put on a plastic watch holder to prevent it from being eroded by sweat.

2) Do not open the back cover of the watch at will, so as not to enter the movement and affect the normal operation of the watch.

3) Do not put the watch in a closet with mothballs to avoid the deterioration of the watch oil.

4) Do not put the watch on the radio or TV to avoid magnetization.

5) Watches that are not worn for a long time should be wound regularly once a month so that the parts will not be in a stationary state for a long time, so as to ensure the operation performance of the watch machine.

Generally, the Amilon watch repair service is mainly divided into two aspects, one is the official after-sales maintenance service center, and only a small number of areas have after-sales service points. There is also a special maintenance service center. ** is different for each region and for different service centers.

The solution to the water in the watch and the fog on the mirror:

Wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 30 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

Note: In order to prolong the service life of the watch, you should try to avoid fog and water droplets in the waterproof watch, do not wear the watch when washing your face, bathing, swimming and other "hydrophilic" activities, do not be affected by water vapor and hot vapor, and pay more attention not to be exposed to rain on rainy days.

Method. 1. Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

Method. 2. If the watch is soaked in water, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it near a 40-watt light bulb about 15 cm, bake for about 30 minutes, and the water vapor in the watch can be moisture. Do not bake the watch close to the fire, so as not to deform the watch by heat.

Method. 3. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will all disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

What should I do if my watch gets water?

1. If the watch is soaked in water, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes, and the water vapor in the watch can be eliminated.

2. Put it in a rice jar and bury it deep in the dried rice for a period of time, if it is fast, you can see obvious results in one night.

3. You can use a granular substance called silica gel to put it into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will disappear.

4. Take a hair dryer to dry, and then apply a layer of transparent nail polish on it to avoid impurities and prevent rust.

5. If there is water vapor in the watch, you can wear the watch face inward and the bottom shell outward, and wear it on the wrist to eliminate the water vapor in two hours. If there is too much water in the watch, the case must be opened and scrubbed. If you are not sure to deal with it yourself, you should send it for repair in time.

Hello, glad to answer for you!

1. If the water ingress is not serious, but there is a layer of fog on the surface, you can use toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly.

Click below to consult the official** or click on the avatar to call for consultation**!

In order to prolong the service life of the watch, try to prevent fog or water droplets from appearing in the watch, do not wear the watch when washing clothes, face and bath, and pay attention not to be exposed to rain on rainy days.

There is fog in the watch, indicating that there is moisture in the watch, and under normal circumstances, if there is a small amount of water in the watch, it cannot be observed by the human eye. Although the watch is sealed, there are still very small pores in the joint between the stem and the handle, the joint between the back cover and the case, and the joint between the case and the case, especially in the old watches. When washing hands, doing laundry, or on rainy days, moisture can soak through these pores into the case.

In addition, the temperature is high and the humidity is high in summer, so if the watch is suddenly cold, the air containing more moisture in the watch will condense into fog or water droplets, which will stick to the watch glass.

The watch is a sealed environment, and it is difficult for water vapor to volatilize on the dial, and if it is placed too long, it will cause the parts inside the watch to rust. The cost of different models of the same watch is also different, it is recommended to call ** for detailed consultation.

Hello, each after-sales service can be found on the official website.

If you find that the watch is flooded, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it about 15 cm near a 40-watt light bulb, and bake for about 40 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch directly near the heat, so as not to deform the glass by heating. Because although there is no moisture on the dial, there may still be water in the movement, and the movement will rust and cause damage to the movement after a long time.

After the watch is flooded, it is recommended to find a professional repair outlet as soon as possible for the master to check and deal with it, which can reduce your unnecessary losses.

What to do if the watch gets water.

It is normal for the watch to get water, if the water is not serious, but there is a layer of fog in the watch glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate water vapor. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

Of course, there are also some daily repair methods for watches to get into the water:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

If the watch gets into the water, take it to a repair shop immediately for disposal.

A fully automatic mechanical watch that operates by the action of the automatic winding mechanism, which winds the winding when the rotor is turned in any direction (visible on the transparent case back). Only when the watch is worn on the hand, the rotor rotates with the movement of the arm to generate energy. Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to replenish the energy of the clockwork.

Only when you wear it on your hand and constantly replenish the energy of the clockwork, will the watch not stop.

There are many reasons why the Amilon watch does not go, such as: there are bumps, movement gears are misaligned, the watch is magnetized, and the oil spring is noisy and the mud is dry, etc., which will cause the mechanical watch not to go. Recommendations for the use of mechanical watches:

1.A watch with a hand-wound movement should be wound at the same time every day as far as possible so that the watch has sufficient energy to operate in the next 24 hours.

2.The energy of a watch with a self-winding movement** is the movement of the wearer's arm, so it does not need to be wound manually under normal wear, only due to the amount of exercise of the wearer.

When there is a shortage of energy to replenish the mainspring, it can be compensated by manual winding, and the crown rotation is controlled within 20 revolutions during winding.

3.If a self-winding watch has not been worn for more than 40 hours, the movement should be reactivated by turning the crown twenty times when it is worn again.

4.To prevent moisture from penetrating the case and to maintain the water-resistance of the watch, make sure that the crown is locked at all times. You can get to:[Room 808, 8th Floor, Block E1, East 1st Office Building, No. 1 East Chang'an Street, Dongcheng District].Carry out maintenance treatment.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Deviation wheel, center wheel failure and other gear train buried faults will lead to the watch stealing stop. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, and you can call after-sales ** to inquire about the after-sales address.

In fact, there are many reasons why mechanical watches do not go, such as: there are bumps, movement gears are misaligned, the watch is magnetized, the sludge is dried for a long time, etc., which are roughly divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can supplement the power grip by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the store for testing.

2. The power is insufficient. If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy.

3. Having been beaten or impacted. The watch is very tight, if it is hit or dropped, it may cause loose damage to the internal parts, and it may also cause time problems, so it is recommended to go to the store for testing.

4. Maintenance is required. A lack of oil or the wear and tear of the internal parts of the movement can lead to problems when the movement starts and needs to be maintained.

5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the error of the time, which will be sent to the store.

Note: 1. Mechanical watches vary according to the model and manufacturing quality of the movement, and the error of the general watch within 30 seconds per day is within the normal range. Some of the higher precision movements can reach around 10 seconds.

Stop, there may be the following reasons:

1. Look at whether the crown is pulled out, and the crown is pulled out, and the watch will stop.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.