My Emilon watch doesn t know why it keeps going fast

Five common reasons for watch time error and watch time inaccuracy:

1) Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2) Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3) Hit or hit: The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4) Need to maintain: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, which need to be maintained, and need to be sent to the designated maintenance point for maintenance services.

5) In addition to the above common situations, the watch is affected by some ambient temperatures: if the hairspring of the watch is magnetized, the watch will not be accurate.

1. The hairspring is stretched and retracted in the work, when the moment of extension, it happens to encounter the external impact force, and the hairspring is affected by the external force, which may be hung on the outer clamp of the fast and slow needle together with the outer ring of the hairspring, or the outer pile pin of the movable outer pile ring, which makes the working length of the hairspring shorter and accelerates the time.

2. After the hairspring is shocked by external force, it may also make the fast and slow needle rotate and displace, and the working length changes.

3. Newly bought watches or watches that have been cleaned and oiled for a short time will lose oil due to excessive oil injection or improper injection, which will make the hairspring partially sticky and shorten the working length.

4. Working or entering and exiting near a large magnetic field, over a long period of time, the hairspring and other parts will be magnetized and put together with each other, and the final result is to cause the watch to stop completely.

When you encounter the situation that the watch suddenly goes fast, there is no need to worry, and you can go to a professional watch maintenance organization for maintenance in time.

Chengdu after-sales service center is located in Room 05, 24th Floor, Sichuan Airlines Plaza.

Hello, it is possible that the watch is magnetized or the power is insufficient. Once the magnetism on the watch is all of a sudden, it goes very fast, even 1-2 hours a day. When wearing mechanical watches, pay attention to keep away from magnetic fields, such as stereos, televisions, mobile phones and other electrical appliances.

Magnetization is a common phenomenon nowadays, and the solution is not difficult, just go to the watch for repair and demagnetization, or bring your own demagnetizer, it only takes 30 seconds to demagnetize the watch, and there is no impact on the performance of the watch.

You can try it by changing the time. If it doesn't work, go to a regular watch repair shop and let the watch masters take a look, so as not to mess up, causing the hairspring to be short, and it will be more difficult to repair it.

For the treatment of faults such as mechanical watches, demagnetization is the first, and it must be neat and thorough; Then check the position error of the watch, continue to check the hairspring, clean the hairspring with alcohol, it will be more fuel and tidy, volatile is good, and the low-quality fuel and magnetic field will make the hairspring show up to circle or attract each other. It is best to do a timekeeping quiz on the repaired watch, and it is best to do a long-term dynamic check to see which all-round rotating experimental rack is to be put on, or to wear it directly to check carefully. Those hidden deep faults can only be detected with the help of relevant instruments.

Magnetization of watches is one of the common reasons why watches go fast, even anti-magnetic watches can not be placed next to electrical appliances with magnetic fields, such as TVs, automatic mahjong machines, etc. Because some of his parts are not anti-magnetic, they will still be magnetized over time. The watch is magnetized and needs to be demagnetized by a professional watch repair facility.

Reasons why the watch goes fast:

1. If the wearer has a vigorous movement acting on the balance wheel, which aggravates the rotation amplitude of the balance wheel, it will cause the watch to swing and speed up the time.

2. The magnetization of movement parts is also one of the main reasons for the acceleration of the watch.

3. The watch has suffered a collision, and there will also be a problem, that is, the secondary outer ring of the hairspring may touch the outer pile of the hairspring, which will appear on the façade and in the dynamic form, which is also one of the fault problems that affect the walking at hand.

Hello, glad to answer for you!

Reasons for inaccurate time: insufficient kinetic energy reserve of the watch, insufficient battery of the watch, the watch has been hit or hit by an external source, the watch has not been maintained for a long time, and the watch is affected by magnetic fields.

Solution: It is necessary to go to the after-sales center for testing and maintenance.

If you have any questions, please call** Please feel free to call.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

1.The power of the table is insufficient.

An automatic watch only needs to be wound by moving your arm, but if you don't exercise much, or if you don't wear your watch for too long, the watch may not be able to run out of time or stop due to lack of power. Of course, you don't have to throw your arms as a hula hoop in order to wind your watch, just move normally.

2.Wearing time is too short.

If it's really caused by too little exercise, don't worry, just take off your watch and shake it horizontally for about 2 minutes before going to bed, and of course you can also shake it for 4 minutes, because then it can walk longer. If your watch can be wound, you can also wind it clockwise. In order for your watch to last longer, it is recommended to have him wear it on your wrist for at least 6 to 8 hours a day.

3.Hairspring failure.

If neither of the above two reasons is the case, it may be the cause of the hairspring. If you exercise too much, the clockwork will be tighter. If it is really a lack of power caused by the winding, usually between 9 and 12 o'clock in the evening, the "calendar function table" at this time his needle wheel began to drive the calendar wheel, the load is large, the watch is tired, at this time if the power is insufficient and no one pushes it, it is easy to stop.

During this time, don't reverse the dial, many mechanical watches have a plastic calendar wheel, and if you are not careful, you will break the gear, if you break the tooth, it will be stuck at this time every day, or it will no longer jump until a fixed date. That's why the mechanical watch stopped.

4.Bump failure.

The parts of the watch are very delicate and small, if you are careless and accidentally bump into it, or if you are healthy and bump into it. This can easily cause the movement parts to fall off or break directly.

All automatic watches must be worn or wound regularly in order to function properly. If the mechanism stops working for a long time, it will cause the watch to deteriorate for a long time. Generally speaking, the power reserve of a large three-hand watch is probably no more than 38 hours, which means that if you do not wear the watch for more than 43 hours, the watch will eventually stop due to the exhaustion of the mainspring.

If you only have one or two automatic watches in your collection, you won't have to worry about wearing them often or stopping them to wind them in order to wind them. But if you have a large collection of mechanical watches, you have to make sure that all the watches don't stop, and everyone will feel a headache and trouble.

Reasons why mechanical watches don't go:

There are many reasons why the mechanical watch does not go, such as: there are bumps, the movement gears are misaligned, the watch is magnetized, the oil sludge is dried for a long time, etc., which will cause the mechanical watch not to go.

Recommendations for the use of mechanical watches:

1.A watch with a hand-wound movement should be wound at the same time every day as far as possible so that the watch has sufficient energy to operate in the next 24 hours.

2.The energy of a watch with a self-winding movement is the movement of the wearer's arm, so it does not need to be wound manually under normal wear, only when the wearer's movement is not enough to replenish enough energy to the mainspring, the manual winding method can be used to compensate, and the crown rotation is controlled within 20 revolutions when winding.

3.If a self-winding watch has not been worn for more than 40 hours, the movement should be reactivated by turning the crown twenty times when it is worn again.

4.To prevent moisture from penetrating the case and to maintain the water-resistance of the watch, make sure that the crown is locked at all times.

A fully automatic mechanical watch that operates by the action of an automatic winding mechanism that winds the mainspring when the rotor is turned in any direction (visible on the transparent bottom cover). It is conceivable that only by wearing the watch on the hand, the rotor will also rotate to generate energy as the arm moves. Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to replenish the energy of the clockwork, but it is not absolute.

Only when you wear it on your hand and constantly replenish the energy of the clockwork, will the watch not stop. Nowadays, there are people who work in the office, and the watch often stops and goes, in addition to the movement, because the wearer itself has insufficient exercise to replenish enough energy to the mainspring.