Remedies for burning engine oil in cars? What are the remedies for burning engine oil in cars?

The treatment methods are; 1. The owner should replace the valve oil seal of the vehicle in time to ensure the valve tightness. The valve oil seal will be aged and seriously worn out after long-term use, and the vehicle with a longer service life or more kilometers is more likely to burn engine oil; 2. The oil with appropriate viscosity can increase the tightness between the engine piston and the cylinder wall, and the use of this oil can alleviate the phenomenon of oil burning, but it cannot be completely eliminated;

3. Replace the piston ring of the car, and regularly clean the carbon of the surface area of the piston ring;

4. Check the oil ruler frequently, and the scale of the oil ruler is generally added to the best between 4 and 5, that is, eighty percent of the position, too much or too little. In addition, regularly replace the oil and oil filter spare parts according to the requirements of the product manual; 5. Choose high-end or high-quality engine oil, especially for engines with turbochargers, because its higher operating temperature and higher oil requirements. Choose an oil with a low volatility rate, as oil volatilization can also cause the car to burn oil.

In addition, choosing a fully synthetic engine oil can greatly reduce the phenomenon of burning engine oil;

6. Develop good driving habits, especially for new cars during the run-in period, the speed should not exceed 90 kilometers per hour, and the engine speed should not exceed three-quarters of the maximum speed.

Through the above methods can solve the phenomenon of engine oil burning, the owner should avoid the above wrong methods in daily maintenance, and prolong the service life of the engine.

The most fundamental way to solve the problem of car oil burning is to disassemble and repair and replace the worn parts, so that although the one-time investment is larger, the durability and reliability and the recovery of vehicle power are guaranteed, as for the use of additives, it is only a temporary solution.

The hazards of burning engine oil in automobiles and their solutions are as follows:

1. Slight burning: fuel consumption, insufficient power, easy to produce carbon deposits, after carbon deposits, it will be difficult to get on the car, and the engine will shake.

2. Severe burning: The oil consumption is very large, and the engine is very worn. When the oil burns out, the engine is about to be overhauled.

3. Identification and inspection: the concentration of blue smoke. Pull out the oil ruler often to see how fast the oil is consumed.

Solution: 1. If the old vehicle burns oil, you can appropriately choose to add oil with relatively high viscosity to the engine to increase the tightness between the engine piston and cylinder wall. Of course, the ultimate way to completely solve the problem of burning engine oil is to overhaul the vehicle more thoroughly in order to fundamentally solve the problem.

2. If you find that the vehicle has signs of burning engine oil, you should always check the scale of the engine oil, regularly replace the oil and oil filter according to the requirements of the product instruction manual, and replace the spare parts of the oil filter.

The solution to burning engine oil is basically to repair the engine, clean up the carbon deposits in the engine, and replace the damaged parts, such as removing the engine cover and replacing the valve oil seal. If the situation is more serious, the engine needs to be overhauled, so when encountering the phenomenon of burning engine oil, it should be dealt with in time.

The reasons why cars burn engine oil are as follows:

1. Poor valve sealing: The valve is to prevent oil leakage into the combustion chamber, but with the increase of service life, there will be wear and aging, which makes the valve seal poor, so that the oil is easy to enter the combustion chamber;

2. The piston gap becomes larger: often for long-term operation, there will be carbon deposition in the piston part, and there will also be a certain degree of wear, with the growth of time, the piston gap continues to increase, and the oil is easier to enter the combustion chamber, which is also often said that after the vehicle is used for a long time, it is necessary to replace the higher viscosity oil;

3. The viscosity of the engine oil is too small: if the viscosity of the engine oil is too small, the phenomenon of burning the engine oil will also occur. The viscosity of the engine oil is too small, it has good fluidity, and it is easy to penetrate into the cylinder, and then participate in combustion;

4. Excessive oil volume: If the oil pressure is too large, part of the oil will be pressed into the cylinder, resulting in the phenomenon of burning oil.

Most of the cars on the market now burn engine oil, and most of them are French cars, German cars, and BMW cars.

The main reason for burning engine oilIn two aspects, one is that there is a problem with the accessories, the waste valve, the valve oil seal, the cylinder is pulled in the cylinder, and the cylinder pressure is insufficient. The second is that the oil circuit is not cleaned for a long time, the antifreeze is not replaced in time, the oil service life is too long, and the piston ring is stuck, and the more common situation is that the piston ring is stuck. Stagnation starts from the oil circuit, the oil bears the temperature at 110 degrees, and the high temperature caused by the long-term unclean oil circuit makes the oil at a temperature of 120 degrees or higher for a long time, so that the oil will fail in advance, the small hole of the oil ring is very small, and the oil inside will be dried and scabbed for a long time, and a cylinder stuck is a liter of oil for 5000 kilometers, at this time, the working conditions of other cylinders will also begin to be bad, and soon the 4 cylinders are stuck, and it will become a liter of oil for 1000 kilometers or even hundreds of kilometers.

Therefore, in order to solve the problem, we must start from the root oil circuit, which is the way to remove the root.

SolutionThere are two ways to solve the problem of burning engine oil, one is overhaul, and the second is PNF repair agent. In the case of overhaul, the cost is very high, the vehicle depreciates quickly, and the later run-in is also very troublesome. First of all, you have to find out the reason for your burning oil, oil circuit blockage, carbon deposits, piston ring stagnation can be repaired with repair agent, there are riders who have repaired it with repair agent before, you can refer to it.

1. Use high-quality fuel; 2. Clean carbon deposits, which can be cleaned with clean lubricating oil; 3. The air filter needs to be checked regularly and replaced in time; 4. If the oil is added too much, you can use the syringe connection pipe to insert and extract the excess oil from the dipstick, or you can go to the maintenance plant or 4S shop to extract it with professional equipment, you should pay attention to the amount of oil, and the oil level is between the highest scale and the lowest scale of the oil dipstick; 5. If there is a problem with the valve seal, replace the valve seal directly. Burning engine oil in automobiles will lead to an increase in carbon deposits in the combustion chamber of the engine, as well as unstable idling, weak acceleration, increased fuel consumption, and excessive exhaust emissions.

The engine oil itself has a certain amount of consumption, and excessive consumption is the problem of burning engine oil. There are many factors that affect the burning of engine oil, such as: fuel quality, driving conditions, driving habits, maintenance habits, etc., the following reasons will aggravate the oil consumption and cause the burning of engine oil, so that the vehicle appears:

1. Carbon deposition occurs in the combustion chamber, which makes the gas ring of the piston ring stuck, and the sealing is poor.

2. Oil sludge is generated in the lubrication system, and the oil sludge blocks the oil return hole of the oil ring and weakens the oil scraping performance.

3. Wear occurs between the piston and the cylinder wall.

4. The valve seal is corroded and aging, and the sealing performance fails.

In addition, cars now have crankcase ventilation systems (exhaust valves), which can also exacerbate oil consumption if there is a problem.

Precautionary measures for burning engine oil:

1. Use high-quality engine oil

Engine oil is very easy to corrode and age in a long-term high temperature state, resulting in the oil film becoming thinner, and it is easier to escape to the combustion chamber to participate in combustion, so the use of high-quality engine oil can greatly delay this phenomenon.

2. Pay attention to the cleanliness of the fuel circuit

Fuel in the combustion process is indispensable to produce carbon deposits, and carbon deposits are the root cause of some car failures, such as the aging of valve seals, piston wall clearance, etc., all have a direct or indirect relationship with the formation of carbon deposits, considering the relationship between domestic oil products, it is necessary to use high-quality engine oil and (PNF) fuel additives to achieve, which is also the key to achieve no dismantling and repair to solve the problem of burning engine oil.

If the oil consumption is relatively large, this is the wear of the internal parts of the engine, the valve oil seal is poorly sealed, the piston ring seal is poorly sealed, and the spindle bearing clearance is too large, which needs to be overhauled, and timely maintenance is carried out to ensure stable, comfortable and safe driving.

It is impossible to completely prevent the burning of engine oil, and the problem of the engine can only be alleviated by changing the oil with strong protective performance. It's best to change the PAO class of fully synthetic, I changed the G T Magic Red engine oil, PAO base oil-based, with the turbo turbo engine special series. The working temperature of the turbine vehicle is already high, and the PAO base oil has good stability, which can control the oil temperature well and will not be too high, so that the engine can be better protected.

Whether it is overhauled should be determined after frequent and comprehensive inspections, after all, overhaul burns money and hurts the engine. My car burns oil, and the power is sick, but I refuse to overhaul it. Directly change the original engine oil, add G T Magic Red, and the power will come to life immediately, which is completely enough and the response is fast enough.

I have never cleaned the PAO engine oil, and even if I have the power to clean the engine every time I change the original engine oil, it is not as abundant as it is now.

EA888 engine, I changed the G T Magic Red oil, the main thing is to have strong protection performance, otherwise it is easy to burn the oil, and the working temperature of the turbocharged engine is high, and the high temperature shear value should be ***. G T Magic Red engine oil is relatively niche, but the base oil is pao, very real, I run high-speed 120 power is also very stable, is a constant feeling.

Normally, as long as you check frequently, you will be fine, because the German car burning engine oil is a design problem, which cannot be completely solved, and can only be replaced with a good fully synthetic engine oil to alleviate the power decline caused by burning the engine oil. My car burns a little oil, I am changing the G T Magic Red oil, this cleaning additive is also good, it can remove oil sludge, on the other hand, the oil of PAO is stable and wear-resistant, which can ensure the performance of the oil under high temperature conditions.

You probably haven't changed the GT Magic Red oil, and if you did, you wouldn't have asked for help. I had a bad oil burn, and then my friend asked me to change the GT, and then it got a lot better.

Hello, if the engine burns oil to change the oil variety is useless, mainly caused by piston, cylinder liner wear or piston ring damage and valve oil seal aging, some models check whether there is a problem with the crankcase waste valve.

Hello, it is useless to replace other brands of engine oil with engine oil, it may be that the valve oil seal is aging or damaged or the piston ring oil ring is stuck, and the engine needs to be repaired to return to normal.

If you are sure that your car is burning oil. This is to check whether the valve oil seal is aging, and check the piston ring is seriously worn, resulting in the phenomenon of burning engine oil.

If there is no obvious improvement in the oil burning, the only way to repair the engine is to repair the engine.

Hello, the car burns engine oil and needs to overhaul the engine, and the effect of oil additives is not great.

There is a way to solve the problem of removing the oil cover of the car burner, and today I will share four ways, 1. Replace the valve oil seal; 2. Replace the piston ring with a new one; 3. Use fuel additives; 4. The main problem of burning engine oil with metal repair agent is that the sealing effect in the engine is poor, which leads to other gases entering the engine oil, such as air and gasoline, etc., so the above four ways can be checked one by one.

There are four common reasons for burning engine oil.

1.If you don't clean the oil circuit for a long time or don't do effective oil circuit cleaning, detergents are used at will, and using detergents and effective detergents are two different things;

2.The antifreeze replacement cycle is too long or not changed at all;

3.The oil change interval is too long;

4.Long-term or often short-distance driving.

The above four points of the vehicle that burns engine oil must be occupied by one or three points.

Precautionary measures for burning engine oil:

1. Use high-quality engine oil

Engine oil is very easy to corrode and age under the high temperature state of the long banquet detection time, resulting in the thinning of the oil film, which is easier to escape to the combustion chamber to participate in combustion, so the use of high-quality engine oil can greatly delay this phenomenon.

2. Pay attention to the cleanliness of the fuel circuit

Fuel is indispensable in the combustion process to produce carbon deposits, and carbon deposits are the root cause of some car failures, such as the aging of valve seals, piston cylinder wall clearance, etc., all of which are directly or indirectly related to the formation of carbon deposits, so keeping the fuel circuit clean is of great help to prevent the burning of engine oil.

3. With the help of external forces

Considering the relationship between domestic oil products, it is necessary to use high-quality engine oil and (PNF) fuel additives to achieve, which is also the key to solving the problem of burning engine oil without dismantling and repair.

If the oil burns lightly, there are two ways to do it**. One is to change the high-quality engine oil, which can improve lubrication and reduce the damage of the engine during work, thereby alleviating the problem of burning engine oil.

The other is the application of engine repair agents, which is suitable for situations where the gap widens due to the coordination within the engine. If oil burn damage is severe, the only way to repair the oil burn is to perform engine maintenance.

This condition can be due to embrittlement damage to the engine valve seals, and the oil ignites or adsorbs on the cylinder carbon deposits as the cylinder reaches the combustion chamber. It is also possible that the engine piston is embrittlement or jamming, causing the combustion chamber oil to catch fire.

Solution: Replace the spark plug and valve seal according to maintenance.

There is a relationship between burning oil and exhaust valves. The exhaust valve is destroyed, and the gate valve is opened and closed. Organic exhaust gases (including oil) from the crankcase ventilation enter the cylinder from the intake valve for ignition, and then the oil burns.

At the same time, the destruction of the wastegate will cause certain harm to the idle operation of the engine, resulting in the engine idling shake or even stalling.

Solution: Go to the repair shop to repair the exhaust valve.

The phenomenon of oil combustion may also be related to the oil-air separator. The oil-air separator is destroyed and loses its function, so it will carry some oil with it when breathing, causing the hydraulic oil to enter the combustion chamber of the engine.