How to set up a wireless network with full coverage, and how to cover the wireless network

There are many smart devices at home, and the signal is poor in places far away from wifi, resulting in device connection and other inconveniences (for example, you want to use the ipad when you want to go to the bathroom, but you just can't connect to wifi). So today, I spent a long time searching for some information on the Internet and summarized it in order to be useful to you. The most important thing is.

1) Position the wireless router reasonably.

1.Try to cross the wall as little as possible.

2.Stay close to places where you regularly use wireless signals.

3.The wireless router should also be placed as far away from the appliance as possible (so as not to interfere with the appliance signal).

Take your phone or laptop and check the signal strength around the room to choose the best place to place it. (A more accurate Network Stumbler software can be installed on the PC to detect the strength of the signal.) There is also a corresponding signal strength detection tool on the mobile phone).

2) Update the wireless network card driver.

3. Buying a dedicated repeater for wireless network repeaters can effectively extend the coverage distance of wifi signals, but it may require complex settings and is relatively expensive.

4. Use electric cats.

The network signal is transmitted via a wire through the "power cat", and the wireless signal is covered to the empty area by means of an extender. Power line network equipment needs to be purchased in sets, that is, in the form of "1+1" or "1+n", and a power line router can generally drive about 10 extenders.

5. Modify the signal channel to reduce interference.

Wireless router + wireless AP

If you don't say anything, you'll find out by searching for yourself.

If possible, every wireless AP can be online. According to you, a wireless AP is about the same.

Do you want to say wifi coverage throughout the house? You can learn about AP routing, which is a device prepared for people who have certain needs for the network.

1. Install several wireless signal amplifiers. Then use a wireless router with bridging function to relay with the original wireless Tongtan device. Switch to a more powerful wireless router, such as an industrial-grade wireless router.

Change the position of the original wireless router and enlarge the height of the middle of the room so that the signal radius is uniform.

2. Method 3: Use a dual-band wireless router. There are 4G and 5G, choose one with two frequencies, the radiation capacity of the signal will be strong, and it can also meet the requirements of WiFi coverage for the whole family; Method 4:

Use a multi-antenna router. Signal coverage can be enhanced to achieve full coverage.

3. Several common wireless network coverage schemes are noisy: AC+ is the abbreviation of accesscontrol, access controller, AP is the abbreviation of accesspoint, wireless access point, mostly seen in commercial use, the advantage is that it can control a lot of equipment, but the cost is high, not very suitable for home use.

If the wireless network wants to cover the whole building, it is necessary to put the road with orange by the device in a spacious place, and it is best to put the router in the center of the house for large households. When in use, mobile phones, microwave ovens, and electrical appliances with wifi modules will interfere with signals, so keep these electrical appliances away from the router.

Many wireless routers have WDS bridging function, and will also support the WiFi signal amplification function, you only need to scan the signal of the superior wireless router, enter the password of another WiFi, you can realize the wireless bridging of the two routers, and easily expand the coverage of the wireless signal. In addition, the router rate is set to 75% at the factory, and the router speed can be adjusted to the maximum to unleash more potential.

The Internet, which is closely related to life, often appears in the process of use, the wifi signal is full, and the web page is "turtle speed"; It is necessary to expand the Wi-Fi coverage area, but the Wi-Fi signal is not good.

Users can enter the router address and username and password in the browser, check whether there is an unfamiliar device in the corresponding menu, and compare the IP address with their own hardware. If you are not familiar with network operations, you can also change your password or call the customer service provider of the network service provider for consultation and complaints.

Several common wireless network coverage schemes: AC+ is the abbreviation of AccessControl, access controller, AP is the abbreviation of AccessPoint, wireless access point, mostly seen in commercial use, the advantage is that it can control a large number of devices, but the cost is high, not suitable for home use.

From the perspective of use effect, among the various wireless WiFi coverage schemes, the signal strength and signal stability of the PoE+AC+AP scheme are basically the best. Because it realizes the signal transmission of each room through the network cable, and there is wireless AP coverage in each room.

Routers and signal amplifiers can affect wifi coverage if they are obstructed by walls. Using professional WiFi signal detection tools, some homes will be equipped with a certain amount of steel, concrete and other materials, which greatly hinder the transmission of WiFi LAN signals.

Direct connection of two wireless routers: Two wireless routers are directly connected to the network cable, which can effectively expand the coverage of home wireless wifi. Connection:

The Extended Wireless Router uses the LAN port to connect to the LAN port of the primary router, do not use the WAN port of the Extended Wireless Router.