What does it mean for the DJI drone to show the gimbal motor overload,

If the app prompts "Gimbal Overloaded", the gimbal tilt control is abnormal or does not follow the direction of the camera well. Please follow the steps below to check whether the phenomenon disappears after each step

1.If the prompt only appears in S gear (sport mode), it is due to the excessive amount of rod that causes the gimbal to exceed the limit, and the phenomenon will disappear as long as the rod is played gently.

2.If a prompt appears in non-S gear (sport mode), please check whether the gimbal is stuck according to the following methods: (1) Please check whether the gimbal protective cover is removed, if not, please remove the gimbal protective cover; (2) If you are using Mavic mini, please check whether you have installed a third-party filter on the gimbal, Mavic mini does not support the installation of third-party filters, if so, please remove the third-party filter; (3) Please place the aircraft flat on the ground to check if there are any foreign objects stuck in the gimbal, and if so, please clean up the foreign objects; (4) If the reminder appears when the fuselage is not there, please check whether the propeller is stuck on the gimbal, if so, please refold the shaft arm to ensure that the gimbal is not stuck; (5) Please check whether the protective sticker on the gimbal camera is torn off, if not, please peel off the protective sticker.

3.Please land the aircraft on the ground, turn it off and wait for 30 seconds before turning it on.

4.It is recommended to check whether the aircraft firmware is updated, if there is an update, please update the firmware to the latest version, if the firmware is already the latest version, it is recommended that you can flash the latest firmware again.

If you have tried all of the above methods and cannot solve the problem, sorry for the inconvenience, it is recommended that you send the aircraft back for testing through self-service repair.

Summary. Once it appears, the "gimbal motor overload" prompts after that. There are two confirmations:

First, has the drone been bumped? If you have been bumped, please note that the gimbal motor circuit or gimbal mechanical part is faulty, so you need to check the gimbal camera thoroughly, if you can't see it with the naked eye, the gimbal reset can't cancel the prompt, you must return to the factory for repair.

The second confirmation is that when the gimbal protective cover was not removed, the power supply of the drone was turned on, and after the protective cover was removed, there was also a prompt that the gimbal motor was overloaded, and then this prompt needed to be processed.

First of all, please land the drone on the ground, turn off and wait.

At this time, place the drone flat on the ground to check if there is any foreign object stuck in the gimbal, if so, please clean up the foreign object;

If the reminder appears when the fuselage is not there, please check whether the propeller is stuck on the gimbal, if so, please refold the shaft arm to ensure that the gimbal is not stuck;

Then calibrate the gimbal, turn off the gimbal for 30 seconds and then turn it on, run DJI GO 4, enter the drone image transmission interface, and click Settings > Gimbal Settings > Gimbal Auto Calibration in the upper left corner.

The DJI T30 motor is overloaded.

There are the following situations: 1. Something in the gimbal is stuck and shouting congratulations; 2. The video recording of the calling bureau during the flight is abnormal; 3. If the gimbal motor is overloaded, recalibrate the IMU, and then perform the PTZ automatic Zheng Lianpai calibration.

Once it appears, the "gimbal motor overload" prompts after that. There are two confirmations first: First, has the drone been bumped?

If you have been bumped, please note that the gimbal motor circuit or gimbal mechanical part is faulty, so you need to check the gimbal camera thoroughly, if you can't see it with the naked eye, the gimbal reset can't cancel the prompt, you must return to the factory for repair. The second confirmation is that when the gimbal protective cover is not removed, the power of the drone is turned on, and after the protective cover is removed, there is also a prompt that the gimbal motor is overloaded, and then it is necessary to deal with this prompt. First of all, please land the drone on the ground, turn off and roll around.

At this time, place the drone flat on the ground to check if there is any foreign object stuck in the gimbal, if so, please clean up the foreign object; If the reminder appears when the fuselage is not overwhelmed, please check whether the propellers are stuck in the gimbal, if so, please refold the shaft arm to ensure that the gimbal is not stuck; Then calibrate the gimbal, turn off the gimbal for 30 seconds and then turn it on, run DJI GO 4, enter the drone image transmission interface, and click Settings > Gimbal Settings > Gimbal Auto Calibration in the upper left corner.

If the gimbal of the aircraft is stuck and cannot be adjusted, please check it as follows:

1.Please turn on the aircraft and remote controller to ensure that the signal is good and clear, that is, there is no lag and gray screen in the image transmission, and then do the gimbal automatic calibration to see if the calibration can pass normally;

2.Try to use the gimbal pitch wheel of the remote control or press and hold the image transmission interface of the app, after the blue circle appears, drag up and down to control the gimbal, if the orange socks can be controlled, it means that there is no problem with the gimbal itself;

3.Calibrate the remote control, toggle the dial wheel, see if the corresponding stroke will change, if the normal can reach the maximum value, it means that there is no problem with the dial;

4.Please set the value of the tilt start and stop of the advanced gimbal settings to the maximum value, if it is set to the maximum value, the gimbal tilt dial will control the gimbal speed very slowly, please lower the value of this parameter.

5.Please set the pitch axis speed to 0 in the advanced settings of the gimbal, if it is set to 0, the tilt wheel will not be able to fluctuate the gimbal, it is recommended to try to set it to 20

If the above steps cannot be solved, please send the product back to Huaishu for after-sales maintenance.

The network transmission signal is unstable.

The network transmission signal is unstable. The DJI drone gimbal was stuck by He Youli because the network transmission signal was unstable and the drone was out of the signal acceptance range. The gimbal of the DJI unmanned robot is a drone used to mount and fix cameras and other tasks.

The network transmission signal is unstable.

The network transmission signal is unstable. DJI.

The drone gimbal is stuck because the network transmission signal is unstable, and the drone is out of the signal acceptance range. The DJI drone gimbal is a drone used for installation, Guhe You, Li Ding, camera and other tasks.

Summary. Hello, the DJI T30 drone shows the reason for the overload of the No. 5 motor, if the app prompts "Gimbal overload", the gimbal pitch control is abnormal or cannot follow the direction of the fuselage well. Please follow the steps below to check whether the phenomenon disappears after each step

1.If the prompt only appears in S gear (sport mode), it is due to the excessive amount of rod that causes the gimbal to exceed the limit, and the phenomenon will disappear as long as the rod is played gently.

2.If a prompt appears in non-S gear (sport mode), please check whether the gimbal is stuck according to the following methods: (1) Please check whether the gimbal protective cover is removed, if not, please remove the gimbal protective cover; (2) If you are using Mavic mini, please check whether you have installed a third-party filter on the gimbal, Mavic mini does not support the installation of third-party filters, if so, please remove the third-party filter; (3) Please place the aircraft flat on the ground to check if there are any foreign objects stuck in the gimbal, and if so, please clean up the foreign objects; (4) If the reminder appears when the fuselage is not there, please check whether the propeller is stuck on the gimbal, if so, please refold the shaft arm to ensure that the gimbal is not stuck; (5) Please check whether the protective sticker on the gimbal camera is torn off, and the DJI T30 drone shows that the No. 5 motor is overloaded.

Wait a minute. Hello, the DJI T30 drone shows the reason for the overload of the No. 5 motor, if the app prompts "Gimbal overload", the gimbal pitch control is abnormal or cannot follow the direction of the spike limb well. Please follow the steps below to check, and after each step, check whether the current guess seems to have disappeared

1.If the prompt only appears in S gear (sport mode), it is due to the large amount of the hungry rod that causes the gimbal to exceed the limit, and the phenomenon will disappear as long as the rod is played gently. 2.

If a prompt appears in non-S gear (sport mode), please check whether the gimbal is stuck according to the following methods: (1) Please check whether the gimbal protective cover is removed, if not, please remove the gimbal protective cover; (2) If you are using Mavic mini, please check whether you have installed a third-party filter on the gimbal, Mavic mini does not support the installation of third-party filters, if so, please remove the third-party filter; (3) Please place the aircraft flat on the ground to check if there are any foreign objects stuck in the gimbal, and if so, please clean up the foreign objects; (4) If the reminder appears when the fuselage is not there, please check whether the propeller is stuck on the gimbal, if so, please refold the shaft arm to ensure that the gimbal is not stuck; (5) Please check whether the protective sticker on the gimbal camera is removed

If the DJI Mavic 2 gimbal motor is overloaded, there are several possible solutions:

Check the load: First of all, you need to check whether the weight of the camera or other device exceeds the load capacity of the gimbal. If the load capacity is exceeded, some of the load should be removed or upgraded to a stronger gimbal.

Adjust the balance: If the camera or other device is not mounted equally, it may cause some motors to be overloaded. Try readjusting the balance point to burn the difference to solve this problem.

Reduced speed: If the gimbal is running too fast, it can also cause the motor to overload. You can try reducing the running speed to reduce the load on the motor.

Replace the motor: If the motor has been damaged or aged, it may be necessary to replace the motor to solve the overload problem.

Check the connections: If the motor is overloaded due to a connection issue, you can check and make sure that all connections are secure and error-free.

Please note that before performing any repair or replacement work, always turn off the power and follow the manufacturer's operating guidelines. If you're not sure how to do maintenance or repairs, ask a peel professional for help.

The DJI Mavex 2 gimbal motor overload may be caused by overload of the slow land motor, mechanical structure problems, foreign objects getting stuck, etc. Here are some possible workarounds:

1.Check the gimbal mechanical structure. If there is a problem with the gimbal mechanic, it may cause the motor to be overloaded and need to be repaired or replaced.

2.Remove foreign body jamming. If a foreign object is stuck, it may cause the motor to be overloaded and disrupted. It is necessary to check the motor and gears of the gimbal to confirm that there is no abnormality in the machine.

3.Disassemble the gimbal for cleaning. Remove dirt and hard objects from the gimbal. If it is too dirty, it may cause the motor to be overloaded.

4.Adjust the motor load. You can try adjusting the center of gravity and focus of the camera to reduce the load on the motor.

5.Adjust the gimbal posture. You can refer to the user manual to adjust the attitude of the gimbal to prevent the motor from being overloaded.

When the DJI Mavic 2 gimbal motor is overloaded, you can try the following solutions:

2.Reduce the load: If the gimbal motor is overloaded due to an overload, you can try to reduce the load, such as reducing the weight of the camera or other equipment.

3.Adjust the parameters: You can adjust the parameters of the motor, such as motor response speed and power, in the settings of the DJI Mavic 2 gimbal to suit different shooting needs.

If the problem cannot be solved by the method of disabling the fiber, it is recommended to contact the DJI after-sales service center for repair or replacement of the motor.

It's a display issue.

First of all, confirm whether the gimbal lock and white plastic buckle are removed, and secondly, check whether the DJI drone has abnormal video performance during the flight.

This problem can also be solved by recalibrating the IMU and then performing the gimbal auto-calibration.