If the household air conditioner press is flooded, how to use the easiest way to eliminate it?

The low-pressure valve is intake, and the high-pressure valve is outlet. Do you suck the water into the low-pressure valve? Tell you casually, once the water enters the compressor, there is no other way than to put the oven, because the antifreeze inside the compressor will float on the water. Or you make a hole under the compressor, and hopefully you won't do it.

1. The basic working process of the cold (hot) water unit is: the outdoor refrigeration (hot) unit refrigerates and cools the cold (hot) medium water (or heats it up), and then the cooled refrigerant (hot) water is transported by the water pump to the fan coil unit installed indoors, and the fan coil unit adopts the method of local return air to exchange heat with the indoor air to achieve the purpose of indoor air treatment. 2. The basic working process of the air duct (road) unit is:

During cooling, the outdoor refrigeration unit absorbs the refrigerant vapor from the indoor unit, compresses and condenses it, and then delivers the liquid refrigerant to each indoor unit. When heating, the outdoor refrigeration unit absorbs the refrigerant vapor from the condenser and delivers the steam refrigerant to each indoor unit after compression, and the indoor unit sucks in the air through the return air outlet arranged on the ceiling, carries out heat exchange and sends it into the air duct (channel) installed in the ceiling of each indoor room, and transmits air to each indoor room through the diffuser on the air outlet. The air duct (road) is designed with a fresh air valve and an exhaust air door, which can replace the air in a certain proportion to ensure the quality of indoor air.

3. The basic working process of the inverter one-to-multi unit is: when the cooling is supplied, the outdoor refrigeration unit absorbs the refrigerant vapor from the indoor unit and delivers the liquid refrigerant to each indoor unit after compression and condensation. When heating, the outdoor refrigeration unit absorbs the refrigerant vapor from the condenser, compresses it, and delivers the steam refrigerant to each indoor unit.

Each indoor unit is arranged on the ceiling by concealed installation. The air is sucked in through its return air outlet, sent in after heat exchange, and then the treated air is sent back to the room by means of local return air from the air supply outlet. The unit is controlled by a microcomputer in terms of energy regulation, and the inverter compressor of the outdoor unit automatically adjusts the working state of the compressor according to the changes of indoor cooling and heating load to meet the requirements of indoor cooling and heating load.

After the compressor is flooded, a small amount of water will still accumulate in the bottom of the compressor casing after simple water filling and drying, and a small amount of tiny water droplets will be wrapped in oil in the refrigeration system pipeline. So it takes two steps to clean up to deal with it.

The first step of the compressor treatment is to drill a hole at the lowest point of the bottom of the compressor with a 4-6 mm diameter drill bit (ground into a three-pointed type), and when drilling, a hard rubber block is used to cover the upper limit of the drill bit, exposing only 5-6 mm. Pay attention to iron filings.

Nitrogen (or 50-60 degrees dry air) is blown into the suction pipe of the compressor (about 5 minutes) to remove the accumulated water and residual oil, and then dry, measure the insulation resistance, seal and weld drilling, vacuuming, oil change, and test drying.

The second step is to blow nitrogen (or 50-60 degrees dry air) in sections of the pipeline system, remove the filter drier (generally not too dirty, drying, sealing and vacuuming can be reused) and replace it, remove the expansion valve (capillary tube can not be removed) and dry, and blow nitrogen (or 50-60 degrees dry air) respectively after removing the evaporator and condenser, and the treatment time is generally more than 1 hour.

After the above two steps are completed, the resealing and welding, the new connection system, vacuuming, fluorine injection, and the test machine. If there is also a slight ice blockage, the filter drier can be replaced once or twice.

Water ingress into the air conditioner - the solution for water ingress into the air conditioner unit.

Check whether the condenser and evaporator need to be cleaned: if there is a lot of dust adhesion, it may affect the heat exchange effect. 4. Check whether there are any obstructions in the suction port and blowing port of the outdoor unit, otherwise it will not only hinder the heat release, but also make the compressor bear excessive load and shorten the life.

Clean the filter regularly to avoid clogging the filter that could reduce airflow velocity, refrigeration and dehumidification. Cleaning steps: Grasp the handle of the dust filter, pull it out, and gently wipe the dust and dirt off the net.

If it is too dirty, it can be finely washed with detergent and dried before putting it into the noodle frame.

Heat exchanger (evaporation equipment and condenser): Generally, it is best to maintain it once every two years, and the dust on the heat exchanger can be blown away with non-flammable, explosive and non-corrosive gases. The water temperature should not be higher than 40 degrees Celsius, and it should not be corrosive such as gasoline.

Strong solvent cleaning. Check whether the wires, piping, heat insulation sleeves, and straps of the air conditioner and air conditioner maintenance device power supply are damaged or loose.

The press change machine, blow the pipeline with nitrogen, I have tried it, it is normal.

The press is disassembled, the refrigeration oil is poured out, and the other pipes are also dried with nitrogen, replaced with new refrigeration oil, the press is installed back, the new filter is replaced, and the filter for cold storage is connected to the return pipe.

Find Gree's professional maintenance personnel for repair.

This is a very serious problem when water enters the aircon compressor as it can cause damage to the compressor. Here are the steps to deal with the water ingress of the aircon compressor:

1.Turn off the air conditioner: First of all, the air conditioner must be turned off to avoid further damage.

2.Check the water source: Check if there are any water sources around that could cause water ingress, such as a leak in a nearby pool or pipe.

3.Inspect the air conditioning lines: Inspect the air conditioning lines for possible leaks or breakages.

4.Drain water: Drain all water. The room can be dried by dehumidification or a hair dryer to avoid further moisture entering the air conditioning system.

5.Replace the aircon filter media: Replace the aircon filter media to ensure that dry air flows into the aircon system.

6.Check the air conditioner condenser: Check the air conditioner condenser and remove the foreign car and dust from it to ensure good heat exchange and air flow.

7.Call a professional maintenance personnel: If the above methods of the leather car still cannot solve the problem, you need to call a professional maintenance personnel to check and deal with it. Maintenance personnel may need to replace the air conditioner, the drunge compactor, or other related components.

Overall, when water enters the aircon compressor, it is best to take immediate steps to resolve the issue to avoid further damage. In most cases, a simple check-up and exclusion is sufficient, but if the problem is severe, you need to seek professional help.

The compressor of the air conditioner is sealed and will not enter the water. If water is ingressive, the compressor is broken. You should find a professional person to repair it.

Is there water in the lubricating oil? If so, treat the air compressor lubricating oil mixed with water according to the following treatment method:

There are many ways to purify, and the simplest method is to settle quietly, that is, to heat the lubricating oil to about 90 in the sedimentation tank for 3 4h precipitation. But this method can only remove part of the water; The second is the distillation method, which can also remove the water from the lubricating oil by distilling it. However, oil separators (serialized as FYQ) are usually used for oil-water separation.

The oil separator rotates at a higher speed, generally at 4000 7000r min. Centrifugal force is used to separate oil and water with different relative densities to achieve the purpose of purification.

For the above explanation, if the air compressor lubricating oil is mixed with water, it is best to clean it according to the above steps to maintain the purity of the air compressor oil, so that the production can be carried out smoothly. If still you can solve 13-91-82-80-880