How to use and maintain the Audi A4 car jack correctly?

Place the car jack (vehicle tool) on solid ground. If necessary, a large sturdy backing plate can be placed under the jack. When the ground is smooth (such as a tile floor), a non-slip mat (such as a rubber mat) should be placed under the base of the car jack.

Look for the mark on the door of your car that is closest to the wheel to be replaced. The markings on the side beams are followed by the support points of the car jacks.

Rotate the automobile jack on the support point of the lower side beam by the handwheel and make it rise as much as possible until the fixed claw 1 completely covers the notch on the car.

Correct the position of the automobile jack so that its fixing claw 1 wraps the notch and makes the bottom plate 2 flat on the car bottom. At this point, the base plate 2 must be located vertically under the support point 1.

Attaching the crank to the car jack: Insert the crank into the opening of the handwheel. Rotate the rocker to the left or right to fix.

Continue to turn the car jack shaker to lift the vehicle until the wheels are slightly off the ground.

It is necessary to ensure the stability of the car jack. On slippery or floppy surfaces, car jacks can slip or sink – a risk of accidents!

Please use only the jack lifting vehicle that was supplied at the factory. If you use a jack from another vehicle, the vehicle may slide down and there is a risk of injury!

Only the car jack is mounted on the specified side beam support points and position calibration. Otherwise, if the grip is not firm enough, then the car jack may slip off the car and there is a risk of injury!

The car jack can only be supported on the specified support points of the side beams.

Cars with jacks in storage bags: The storage bag with the jack is fixed to the retaining ring of the luggage compartment and must be securely fastened again after use.

The jacks on the car are maintenance-free.

Hello, for the correct use of the jack, next to the four wheels, there will be a clear sign as a fixed position for the jack to use, do not support the jack on the bumper, beam, lower skirt and other positions, so that it is very easy to damage the vehicle. When turning the rocker arm, the support bar cannot slip out of the support point, the ground supporting the jack must be hard, if there is no way to work on the softer ground, a strong backing plate should be laid. Be sure to pay attention to balance when supporting the jack.

Never start the engine when the vehicle is lifted, as the vibration of the engine or wheels will cause the vehicle to slide off the jack. For the maintenance of the jack, it is best to add lubricating oil to it every once in a while to prevent rust, and at the same time, do not often place some heavy objects on the jack to avoid crushing the parts. In addition, it is also necessary to pay attention to dust prevention, too much dust covering the surface for a long time will also make the jack surface rust.

The Audi A4 is located under the trunk cover. 【Get Reserve Price for Free】The trunk is opened, and under the innermost cover, near the rear seats, is the place where the tools are placed. The jack box is also in the trunk, and the warning triangle is on the trunk lid.

In terms of appearance, the 2020 Audi A4 adopts the latest family-style design language, with a larger grille size, while the size of the fog lamp area on both sides has also been increased, with sharp LED headlights, the overall look is extremely exquisite and dynamic.

Car maintenance precautions.

Changing the engine oil is the most common item in maintenance, and the oil mainly plays the role of lubrication, because the engine oil has a life cycle, so it should be changed regularly. The oil filter element is also called the oil filter, its function is to remove various impurities in the oil and ensure the normal lubrication system.

Dust and grit in the air can easily lead to wear between the piston rings and cylinder liners in the engine. Over time, the carbon deposits on the piston will become more and more, which will cause the engine to idle unstable, increase fuel consumption, excessive exhaust gas, and in severe cases, it will also lead to the engine burning oil weakness. Get the reserve price for free

On-board tools, car jacks, tire repair kits and electric inflatable pumps are located under the floor cover in the luggage compartment.

The Audi A4 car jack, tire repair kit, and electric pump are all under the floor lid of the luggage compartment. The Audi A4 is a popular B-segment sedan produced by FAW-Volkswagen and launched in April 2003. It fills the gap of domestic B-class cars and strengthens FAW-Volkswagen's leading position in the domestic luxury car market.

As the first models to introduce a long wheelbase and a turbo concept, sales of the B5 to B8 and A4 have been enduring for a long time. **The A4 abandons the tearful design and adds the Quattro four-wheel drive mode, which has a more sleek and sporty appearance, and more power and handling. The interior of the model is exquisitely made, the technology configuration is rich, and the empty rooms are abundant, which has good practicality in the B-class model.

Audi A4 is sold in three displacements, namely. Among them, it is divided into four types: manual basic type, automatic basic type, comfort type and technology-leading type. There are three types of displacement: comfort, sports comfort, and comfort.

With only one displacement, the quattro all-wheel drive system is installed. The Audi A4 produced by FAW-Volkswagen is the first B-segment car of an international luxury brand in China, filling the gap in the domestic B-segment and strengthening FAW-Volkswagen's leading position in the domestic luxury car market.

Place the car jack (on-board tool) on solid ground. If necessary, place a sturdy mat under the jack. When the ground is flat (such as a tile floor), a non-slip mat (such as a rubber mat) should be placed under the base of the car jack.

Look for the mark on the sill that is closest to the wheel you want to replace. Then the mark on the middle side beam is followed by the support point of the car jack.

Rotate the car jack on the lower threshold support point with a handwheel so that it is raised as high as possible until the fixing claw 1 completely covers the notch of the car.

Correct the position of the automobile jack so that its fixing claw 1 covers the notch, and the bottom plate 2 is placed flat at the bottom of the car. At this moment, the base plate 2 must be located vertically below the support point 1.

Install the crank on a car jack: Insert the crank into the opening of the handwheel. Or turn the crank from side to side to repair it.

Continue to turn the crank of the car jack to lift the vehicle until the wheels are slightly off the ground.

Ensure the stability of the car jack. On slippery or soft ground, car jacks can slip or sink – there's a danger of accidents!

Please use only factory-supplied jack lift vehicles. If you use the jack chain top of another vehicle, the vehicle may slip off and get injured!

Install the car jack only on the specified side sills support points and calibrate the position. Otherwise, if the grip is not firm enough, the car jack may slip off the car, causing injury!

The car jack can only be supported on the designated support point of the side beam.

Cars with a jack for storage bags: Storage bags with a jack are fastened to the retaining ring of the luggage compartment and must be securely re-fastened after use.

The jacks on the car do not require maintenance.

Millions of car purchase subsidies.

Before using the jack, the car should be parked on a flat and solid road, then the vehicle should be fixed, a tripod should be placed behind the car, and finally the chassis support point should be found.

There are two main types of common truck-mounted jacks, rack jacks and screw jacks, and rack jacks are more common.

The precautions for the use of jacks are as follows:

1. Flat and solid horizontal pavement. A flat and solid road surface is the basis of subsequent operations, and it is easy to cause accidents due to displacement after the vehicle is lifted if it is not flat. In addition, if the pavement is loose mud and sand, it is necessary to place harder and flat planks, bricks, etc. under the jack to improve the bearing capacity of the pavement, otherwise it is easy to cause the jack to collapse.

2. Fixed vehicles. The automatic transmission car can directly pull the handbrake to hang the P gear, and the manual transmission in addition to pulling the handbrake, remember to hang the gear to the first gear or reverse gear. Because the manual car brake can only hold the rear wheels in place, the gears can be secured to the front wheels using engine brakes.

3. Place a tripod 50 meters behind the car (150 meters away at high speed).

4. Find the chassis support point. This is also very important, each vehicle has a special support point, generally in the vehicle chassis on both sides of the edge near the car shouting crack wheel place, jack lifting part must be supported to the chassis support point, otherwise the vehicle will be unstable, but also easy to damage the jack and the car chassis. (Photo by Zheng Guanwen:.)

Pacific Automobile Network Chen Jie 2).