The computer boots up 50, and the computer boots up

Press F8 at startup to build, enter safe mode to try, or find the installation disk of GHSOT, use the PE tool inside to enter the system, and copy the file.

If you have a USB flash drive at hand, you can make a bootable USB flash drive PE, see My Space.

According to the prompt, there may be a problem with the data cable of the hard disk, try to connect it again, but it can't be replaced.

You can go to the PE system first to copy out the data of your computer's C drive, and then reinstall the system.

You can turn on F8 to enter safe mode. I take the USB flash drive away and install the system from it.

There may be a problem with your hard drive, but a different one might work.

Boot requires pressing F1 to enter the system troubleshooting.

Under normal circumstances, the requirement to press F1 to enter the system is caused by a minor problem with the system's BIOS settings that do not affect the system startup, so please check the hardware information settings in the BIOS for discrepancies with the actual situation.

The common faults in general are:

1. The battery on the motherboard is dead.

Solution: Replace the motherboard battery.

2. You have set up the floppy drive to start, but there is a problem with your floppy drive.

Solution: A. Press del to enter the BIOS at boot, boot up the boot sequence, and turn off the floppy drive to boot.

b. Turn off the detection function of the floppy drive when it is turned on

Start the computer and press the [DEL] button to enter the main BIOS settings interface.

Select "Advanced."

biosfeatures", press the enter key to enter;

Add "boot

upfloppy

seek" is set to "disabled", so that the boot software detection function can be disabled.

Press the DEL key after powering on, enter the BIOS, and move the cursor to StandardCMOS

features, move the cursor to drivea, press enter, select none, press the F10 key, and then press the Y key to save the settings and press enter. There is also a floppy drive controller, which is integrated

peripherals, move the cursor the same way to find SuperIoDevice (or: io

devices

configuration

Press enter and find Onboard

FdccontrollerEnter, select Enabled, save the settings with the above method, press Enter to enter the system after boot POST, at this time the floppy drive is blocked.

After my computer is installed with the program, there is also this problem, I am on the blos in the blind tidy, just can't install the program, the optical drive is also installed, and it won't work after a while, others say that the blos are changed, and the brand machine is good to have this problem.

The button battery on your computer's motherboard is dead, go buy a new one and install it and reboot the system, boot the computer and press the del button, enter the BIOS settings, select the first item, and find that the floppy drive is set to, but in fact there is no floppy drive in the chassis, after setting this item to none, troubleshooting.

The first thing to do is to replace the motherboard battery. After letting, press F1 to power on. After entering the system, you can adjust the time.

This is because the motherboard battery is dead and the BIOS settings cannot be saved. After entering the BIOS, turn off the floppy drive, and you don't need to press F1 when you boot it in the future.

When you turn on your computer, F1 and F2 will appear on the screenIf I don't press any of them, I won't turn on. But when the machine was turned on, everything in it changed, and the time went back to 08. Please help me open normally....Detailed.

Turn on, press F2 to enter the BIOS, adjust the time in the first item, there is a setting floppy drive under the time, set it to off, F10 save and restart.

Without waiting for it to restart,Turn off the computer,Unplug the power supply,Reboot F2 into biso,See if the time goes back to 08 years,Yes,It means that the button battery on the motherboard is dead.,Go buy a new one.,Follow my first steps to re-operate it.。