The distance between the strings of the electric guitar and the straight board is too high

It is normal for the guitar to appear to play after a while, especially in winter, the climate is dry, and if there is some heating equipment, the piano is easy to deform, so don't frustrate the frets at will.

First rule out the influence of the above reasons, keep the piano away from any heating equipment, try to make the ambient air a little humid, and then consider frustration if it has not recovered after a while.

Change the strings, no, let's talk about the next step, don't adjust the steel bar casually, it shouldn't be a problem with the steel bar, don't frustrate, unless you're going to buy a new one.

The best way to do this is to relax the strings all the way first, preferably all of them. In this way, the straight board will slowly return to its original appearance. This is the safest way to do it.

In the case of guitar plucking, each string has a screw (upright) that controls the height of the string.

Loosen the string first, then tighten the screw into place, and you're good to go.

In the area where the fine tuning is located, there is a hole for tuning the height of the strings.

Take the corresponding screwdriver and you can adjust it.

Actually, I don't think it's a big deal to play electric guitar. Let's fight.

You can't play with an empty piano either.

You tell me. You shouldn't be able to hear it when you plug in the speaker effects.

If you really feel like a hitter, tighten the strings.

That's caused by your own neck, you now need to tune the neck to the correct position, then fine-tune the bottom of the string with the smallest Allen wrench, tune the 2nd string until it doesn't hit, and then readjust the octave with the tuner!

1.Grind 2 frets with a frustration. 2.A hex wrench fine-tunes the strings. 3.Look at the height of your 12-fret strings and frets, preferably within centimeters.

Even for the piano, not the guitar. Hehe.

Whether it's an electric guitar or a folk guitar, if you don't use it for a long time, there will be a similar situation such as playing or changing voices. Tighten the strings a little bit and talk slowly for a while, it may not feel very good. It's okay to adjust it slowly.

Maybe you don't have to tune it at all. Because the strings are elastic, it's good to use them.

Twist in the direction of a string, but it should be noted that it can only be twisted little by little, not a lot of hand twisting, and the neck must be patted every time you finish twisting, otherwise it is easy to break the string.

The inside of the neck is made of a steel bar, which is not usually found on classical guitars, and is only found on folk and electroacoustic guitars. In fact, the principle of steel bar is very simple, mainly by changing the length of the steel bar, in order to achieve a mandatory adjustment to the curvature of the steel bar. If the string spacing is too high, you will need to press the strings more vigorously when practicing, and your fingers will be more likely to be injured.

Therefore, once you find that the distance between the strings is too high, you must adjust it in time, otherwise it will hurt both your hands and the piano.

This is called copy spacing, and can be adjusted by grinding the pillow and bridge bai.

du。Generally, the closer the string is to the fretboard, the better the feel of the left hand zhi, but at the same time, the feel of the right hand becomes worse in the opposite direction, and the dynamic range of the sound becomes smaller, that is, the volume of the head of a tone becomes smaller, and the feel for the right hand is that the strings are dull, cannot be played, and it is easy to play. Therefore, the distance between the strings and the fretboard is not as low as possible!

This distance needs to take into account the feeling of the left and right hands at the same time, rather than only the left hand and the right hand, and the best state is that the strings are neither high nor low from the fingerboard, and within a certain range, it is best to make the left and right hands feel good.

The distance between 2 mm and 4 mm is normal. How high you want to adjust it depends on your preferences. Most people like to adjust the string pitch of the 12th frets to about 3mm.

The position of the twelfth fret, the string distance indicator should not be missed by 5 mm.

Play all the notes just without hitting the frets or slightly hitting the frets.

The string spacing is 3 mm.

The two hex screws on both sides of the bridge were raised.

In addition to the quality of the innate issues aside, your practice time will also determine your fretboard, and if you don't play it often, he may cause the fretboard (neck) to bend and go out of shape! Some people play once a few weeks, or play for a few minutes, and then let your guitar rest on the couch for a few days, and it's the same! The humidity of the air, combined with the wood of the guitar itself, bends!

Here it is emphasized that the guitar is actually a matter of course, but the good guitar goes slower, and the bad guitar goes faster! Your guitar should have an Allen screw that adjusts the neck! Usually inside the articulation hole, or near the headstock!

I loosen the strings a little! Adjust the hexagon to see the fretboard bulge or concave! It depends on the situation of the piano!

You also need to calculate the tension of the strings, because the originally curved neck will also become straightened due to the tension of the strings! So this method is more time-consuming! In addition, the strings of the folk song are also divided into several models!

The thickness of the strings directly affects the curvature of the neck, so don't change the strings of the same model as soon as you open it! Incorrect string changes can also cause the neck to bend, for example, if the strings are all loose, and then 6 pieces are replaced! This hurts the neck a lot!

I want to change one and loosen one! One last resort! Change your guitar!

Haha, if you really like it, spend more money to pull!

The distance between the strings and the fretboard should be better.

At 1 fret, no more than 1mm 12 fret, no more than 4mm, if there are too many, it will be difficult to press the string, and the pitch will be inaccurate when pressing the string, so the distance between the fretboard and the string is a very important problem. 6mm is definitely not accurate, it's time to tune it.

Your string height is already too high, on the one hand, you have to see if the pillow and saddle can be polished and adjusted. It is very likely that the neck is already bent, so the inner tendon of the neck can be adjusted appropriately.

Yours is a ballad so it's not as well tuned as an electric organ, and the neck and bridge can be high.

When you go back and change the set of strings, remember to make the strings as soft as possible, which is good for the neck and good for playing.

Incorrect string changes will affect! As for the feel, of course, the freshly changed strings are not as good as they used to be.

1: You can use a small saw to cut down the string pillow of the headstock, which is the position of each string.

2: The bridge at the back of the guitar can be removed and sharpened a little.

It won't be so high that way.

Guitar string pitch high:

First, it depends on whether the neck is bowed, and the neck must be straightened before moving on to the next step.

Second, if the neck is still straightened or high, then only the two small pillars of each string of the bridge can be adjusted, note that it is clockwise.

Wring. Third, you must pay attention to the amount, because it is likely to be hit after the adjustment.

Adjust the chord spacing Don't be in a hurry, find it slowly, and finally tune out the best feel!