How to dismantle the PVC ceiling in the bathroom? Don t be destructive

Waterproof gypsum board: waterproof gypsum board is made of light steel keel, you need to be careful not to touch the light steel keel, in addition, the gap between the gypsum board is treated with gypsum and caulking tape, and the outer layer is coated with putty and paint, so be careful not to loosen the keel when dismantling.

You can buy a suction cup first, use the suction cup to stick to one corner of the square, and then pull the corner of the aluminum gusset hard to warp up, and the other three corners can be removed in the same way.

The gusset is a PVC gusset ceiling material, which is made of polyvinyl chloride resin as the base material, adding a certain amount of anti-aging agent, modifier and other additives, and is made by mixing, calendering, vacuum blister and other processes.

2.This kind of PVC gusset ceiling is especially suitable for kitchen and bathroom ceiling decoration, with light weight, moisture resistance, heat insulation, non-combustible, non-vacuuming, easy to clean, paintable, easy to install, low and so on.

There are many varieties of gusset ceiling patterns, and the varieties of colors that can be selected are: milky white, beige, lake blue, etc.; The patterns are: epiphany, peach, bear bamboo, cloud dragon, lattice flower, parquet, etc.

The plastic gusset is made of PVC as raw material, the main advantages are: light weight, easy installation, waterproof and moisture-proof, moth-proof, the surface of the pattern changes are also very many, and pollution-resistant, easy to clean, sound insulation, heat insulation good performance, especially the new process to add flame retardant materials, so that it can be extinguished from the fire, safer to use. Compared to metal ceiling panels, the disadvantage is that the service life is relatively short.

The last corner strip of the PVC gusset ceiling is glued, and it can be removed from the beginning after being found.

Look on both sides, the beginning of the block is a whole block, and the end is definitely not a whole piece.

If it doesn't take long, you can. You see where the top gusset finishes when it is installed, and you start to remove it from that side. The first piece generally does not use gusset wire. As long as the first piece is carefully removed, the latter will be simple.

PVC is a flexible ceiling method to go! You can push from the middle to the top!

PVC gusset ceiling material is made of polyvinyl chloride resin as the base material, adding a certain amount of anti-aging agent, modifier and other additives, through mixing, calendering, vacuum blister and other processes. How to dismantle the PVC ceiling? Next, let pchouse answer for you.

PVC gusset is mostly used for the strip-shaped plate material of room ceiling and room partition, and the building material produced by hollow PVC material in the middle can be divided into sheet floor and coil floor from the shape.

1. When the original PVC ceiling decoration is removed, it should be completely dismantled, and the original ceiling decoration structure should not be retained.

2. In particular, the structures that carry the weight of the ceiling such as the boom and pendant in the original ceiling must be removed, which may also affect the later installation.

3. When dismantling, the power supply should be cut off first, and the original circuit pipeline in the ceiling should be removed as much as possible.

After installing the ceiling for a period of time, if you want to clean or check the pipeline problem on the ceiling or the roof leakage problem, you need to remove the bathroom gusset and then repair it, but some owners do not know how to disassemble it and dare not dismantle it casually. Let's bring it to youBathroom ceiling demolitionUnloading method.

First, the bathroom ceiling dismantling method.

1. Use a wallpaper knife to insert the aluminum ceiling board along the gap: swipe back and forth a few times to find the position of the clip, and then squat gently, squatting in the middle first, the sides are easy to deform.

2. Square aluminum buckle plate: the long buckle aluminum buckle plate needs to be removed from the next buckle plate, and then removed in turn; The long single-buckle aluminum gusset can be sung down with a small flathead screwdriver, and the single gusset can be removed separately.

3. Long PVC ceiling board: first look at the installation and trimming corners of the PVC board to see if it touches the glass glue, if it does, please cut it off with a utility knife. Then, insert a flathead screwdriver or utility knife into the rear piece and the penultimate jaw, gently swing it up and down, and after a while, the PVC board will become loose.

4. Then push the board to the left or right side of the trimming corner, turn one side down, then grab one side down with both hands, gently go down a little bit, and with a little force, pull it out. Then use a Phillips screwdriver to remove the inner plate, because the female seam of each PVC board is a self-tapping screw, please tap the self-tapping screws first, and then remove it slowly without breaking.

5. After opening the pipe hole, first place the disassembled plate in the direction, then mark the place where the pipe hole needs to be opened, then place the purchased pipe vertically at the mark, draw a circle with a paint pen to follow the pipe and use the hole opener to open the hole. Once done, install it according to the original path and place the glass glue around.

2. Precautions for dismantling the bathroom ceiling.

1. If there are no electrical appliances or wires in the ceiling, the dismantling work can be completed very quickly. However, if there are electrical appliances such as bath bombs and electric water heaters, the power supply must be cut off before disassembling to prevent leakage or electric shock. If you want to use these devices again, you should handle them with care when removing them.

2. If it is a 20-year-old house with a suspended ceiling, you should pay more attention to safety. Because sometimes, if you demolish one place, it may cause another place to fall directly, so be aware of the aging of the ceiling. When carrying out dismantling work, it is advisable to remove all the old lines; Because the wires are old, there is no need to use them.

If you use them again, you can easily get an electric shock accident.

3. There are some integrated ceilings, with hangers and pendants, which are easy to cause potential safety hazards to future life, so it is recommended that you keep them tidy. If everyone is plastic or plastic steel integrated ceilings, it is not recommended that you do it yourself, or ask professionals to work more reliably.

4. When the original ceiling decoration is removed, attention should be paid to removing it as much as possible and not retaining the original ceiling decoration structure. In particular, the structure that carries the weight of the ceiling such as the boom and pendant silver collapse in the original ceiling must be demolished, which is mainly from the safety considerations in the future.

1. The ceiling is dismantled only by collecting it on the ceiling with a tool, and then sucking all the air inside, and at the same time pulling out a corner with the help of suction, and then according to the same method, pull out all four corners.

2. After the outer plate is removed, an auxiliary keel will be installed behind each plate. These auxiliary keels are connected to the main keel. As long as the secondary keel is removed, the main keel can be easily removed, and then positioned in the correct position to remove them one by one.

3. The last piece of plastic gusset is directly glued to it. Just move it firmly onto the wall. When moving hard, tap the gusset with your hand.

After removing this part, use screws to secure the other parts. If it is fixed, make a few strokes along the glass glue, then insert it into the gap of the edge banding, gently pry it open, and then disassemble it one by one from the side, and it is done.

If the bathroom ceiling is installed, if there are problems such as water leakage, the owners must remove the bathroom ceiling for maintenance. What are the ways to dismantle the bathroom ceiling? Bathroom ceiling removal is generally dismantled square, strip aluminum plate or PVC board hail cautiously, bathroom, bathroom ceiling cleaning is usually cleaned with a soft cloth.

First, the bathroom ceiling removal method

1. Square aluminum plate

When the bathroom ceiling is removed, you can use a suction cup to connect one corner of the aluminum plate, and then pull the corner of the aluminum plate to pull it up. Other angles of the aluminum plate are also consistent with the method, and the aluminum plate can be used. When dismantling, this method of disassembling the square aluminum plate will not scratch the ceiling and is simpler.

2. Strip-shaped aluminum plate

When removing the ribbon aluminum plate from the bathroom ceiling, you need to find the last aluminum plate to be installed, then gently wipe the glass glue between the edge and the tile with a thin iron, and then insert the sealing ring. In the gap between the two sides, slide the clip back and forth after determining the position of the clip, sliding it down.

3. PVC board

When the strip aluminum gusset is removed from the bathroom ceiling, the closure is usually located on both sides, and the hanging plate can be pushed to the side of the ceiling by hand. If the loose part is the last piece, push it hard to the side and pull the PVC board down. In this way, they are disassembled one after the other.

Second, the cleaning method of the bathroom ceiling

Some of the common water vapor in the bathroom is relatively large, and the suspended ceiling will leave some water stains. I usually just need to wipe the ceiling with a soft cloth, usually after a month or two. Deep cleaning, i.e., cleaning with a soft cloth, needs to be wiped with water, then the doors and windows of the bathroom need to be opened, and ventilated to dry.

If the ventilation of the bathroom is not very good, you can choose to use a better quality paper towel to wipe the ceiling.

The above is the method of removing the bathroom ceiling and the cleaning method of the bathroom ceiling. In daily life, owners should keep the bathroom clean, if the bathroom has a suspended ceiling, it should be wiped frequently, and at the same time, the doors and windows should be opened frequently, so that the bathroom can be ventilated and kept dry and respectful.

You can get it for free

Modern society for the integrated ceiling many people do not know a lot, they only know that the installation of the integrated ceiling will be beautiful, however, do not know how to disassemble the integrated ceiling in a special time, today here for you to introduce how to disassemble the bathroom ceiling, bathroom hole round boring ceiling disassembly steps.

How to remove a bathroom ceiling?

1. Waterproof gypsum board disassembly method.

Some kitchens will use waterproof gypsum board as the material of the ceiling, because the surface of the waterproof gypsum board has fallen off in the long-term use, and because of the smell of oil smoke caused by a certain stain on the surface of the waterproof gypsum board cavity source and is not easy to clean, so it needs to be removed, and then redecorate. In addition, the gaps between the gypsum boards are treated with gypsum and caulking tapes, and the outer layer is coated with putty and paint, so be careful not to loosen the keel when dismantling, so as not to have problems in the next decoration.

2. Aluminum gusset disassembly method.

Now the ceiling of the kitchen in the family adopts a lot of aluminum gusset, the aluminum gusset is basically a square, the size is 30cm*30cm, if you want to do it yourself, you can go to a suction cup first, use the suction cup to stick to a corner of the square, and then pull the corner of the aluminum gusset plate hard, and the other three corners can be dismantled by the same method, so that the way of bending can effectively remove the labor cost of disassembly.

What are the steps to remove the bathroom ceiling?

1. The disassembly and cleaning of the integrated ceiling is also convenient, as long as three small steps: suction, pulling, and disassembly. The manufacturer will be equipped with a small tool, as long as you gently close it on the board, suck the air away, suck one of the corners, and then pull it out hard, pull out the four corners, you can disassemble the whole board and clean the inside.

2. After disassembling the outer plate, you can see the internal structure. Among them, each plate is equipped with an edge banding auxiliary keel around it, and the auxiliary keel plays the role of connecting the module and the light steel keel to ensure that each plate can be closely connected to each other.

3. When dismantling, the safety of the equipment and facilities in the original ceiling should be considered, many old houses in the last century have heating pipelines in the ceiling, and some residences are air-conditioning systems, so as to avoid damage to pipelines and equipment due to inattention to demolition.

4. When removing the original ceiling in the kitchen and bathroom, avoid damaging the ventilation duct and flue.

We sometimes encounter the problem of dismantling and replacing the bathroom ceiling, such as buying a second-hand house and renovating it, or the ceiling in the home is broken and needs to be replaced. So when these problems arise, we should deal with them in time, and let's introduce you to the bathroom ceiling replacement? What are the precautions for the replacement of suspended ceilings?

We sometimes encounter the problem of dismantling and replacing the bathroom ceiling, such as buying a second-hand house and renovating it, or the ceiling in the home is broken and needs to be replaced. So when these problems arise, we should deal with them in time, and let's introduce you to the bathroom ceiling replacement? What are the precautions for the replacement of suspended ceilings?

Bathroom ceiling replacement?

1. Waterproof gypsum board disassembly method.

We know that some kitchens will use waterproof gypsum board as the material of the ceiling, because the surface of the waterproof gypsum board has fallen off in the long-term use, and because of the smell of oil smoke caused by a certain stain on the surface of the waterproof gypsum board and is not easy to clean, so it needs to be removed, and then redecorate.

2. Aluminum gusset disassembly method.

We know that the ceiling of the kitchen in the family now uses a lot of aluminum gusset plates, aluminum gusset plates are basically a square, the size is 30cm 30cm, if you want to do it yourself, you can first buy a suction cup, use the suction cup to stick to a corner of the square, and then pull a corner of the aluminum gusset plate will be warped, and the other three corners can be removed by the same method The aluminum gusset can be removed, so that the labor cost of dismantling can be effectively removed.

3. Disassembly method of plastic or plastic steel plate.

Because such materials require professional tools to be disassembled, and if you are not careful, the original structure will be damaged or you will not be able to install it during renovation. It is necessary to hire professional demolition personnel to carry out the dismantling work, so as to ensure the smooth completion of the redecoration.

What are the precautions for the replacement of suspended ceilings?

1. When the original ceiling decoration is removed, attention should be paid to the removal as much as possible, and the original ceiling decoration structure should not be retained. In particular, the structure that carries the weight of the ceiling such as the boom and pendant in the original ceiling must be removed, which is mainly for future safety considerations.

2. And when dismantling, the power supply should be cut off first, and the original circuit pipeline in the ceiling should be removed as much as possible, and no longer consider continuing to use, because the original circuit in the ceiling has basically no use value.

3. When dismantling, the safety of the equipment and facilities in the original ceiling should be considered, many old houses in the last century have heating pipelines in the ceiling, and some residences are air-conditioning systems, so as to avoid damage to pipelines and equipment due to inattention to demolition.

4. When removing the original ceiling in the kitchen and bathroom, avoid damaging the ventilation duct and flue.

What we have introduced to you above is about the replacement of bathroom ceilings? The relevant problems of the precautions for the removal of the ceiling, the removal and replacement of the ceiling in the bathroom is relatively troublesome, so we need to understand how to operate, so that when we encounter these problems, we will know how to deal with them.