How many spark machine discharges can a person calibrate the meter every day?

Basically, you can verify about three to five times a day, and this is still a relatively familiar process to be realized, and practice more.

The discharge of the spark machine can be corrected for a person per day, which should be 25. There are less than 25 depending on the situation, and the specific problems will be analyzed on a case-by-case basis.

A person can adjust the meter for a few minutes a day, and under normal circumstances, about 40 meters are already a lot, which also requires skilled people.

There are generally more than 300 of the daily callable meter minutes that can be called every day, which are normal values.

The number of discharges that a person can call for two minutes a day is about 10 to 15, because this is also rated.

The spark machine discharges a person every day with a ridiculous watch. A lot, because this school schedule can only be solved according to how fast or slow they are, so they are daily. There are many longevity pills and should be calibrated.

It depends on each person, he has one per day, but sometimes some schools have two per day.

How many minutes can a person calibrate the meter every day when the firecracker is discharged? Because of the spark machine discharge, how many varsity teams can a person have per day? We need to look at your results through your workload, and we can also calculate it through the network.

If every day, he sees your contribution value and points it.

How many sparks can be placed in the table per day, it depends on one of your own techniques or abilities.

He is a spark machine that can be opened in style, and everyone is different when it is discharged.

The song is calculated according to the proficiency level of each person.

How many spark machine discharges can a person calibrate the meter every day? The spark machine discharges one person can calibrate the meter for minutes per day. Probably, dozens of them.

How many spark machine discharges can a person calculate the meter every day, and determine how many he puts according to its model.

The spark machine discharges, and a person can call the meter minutes every day.

How to calibrate the table, small factories generally use the fallacy filament table for calibration, you see people operate once, understand, try a few times slowly, fast or slow is just a matter of experience, some large factories use standardized fixtures such as erowa, the efficiency of external clamping is high, and the investment is larger.

Touch! Count on both sides of the workpiece.

Touch the side and return to 0

Then touch the other side, write down the number and take the middle, and that's it.

But the premise is to calibrate several sides of the workpiece.

Absorb the dial gauge on the spindle of the machine tool, point to the datum of the template with the dial gauge head, move the work surface of the machine tool back and forth until the pointer of the dial gauge is zero and do not move, and then press the template, and then re-check it after compression, see if the template moves in the process of compression, if everything is normal, the correction work of the template can be over.

The copper male you are talking about is the electrode for EDM, the correction electrode first needs to hit the dial gauge on one side of the electrode, shake the handle of the machine tool, check the direction of the electrode tilt, see how much the difference between the highest point and the lowest point is only, and adjust the electrode to the opposite direction. This is to adjust the horizontal direction of the electrodes, and then also the vertical direction of the electrodes; Again, hit the dial gauge on the side of the electrode, let the electrode move up and down, and adjust the verticality of the electrode. There are adjusting screws on the EDM head, which can adjust the verticality of the electrodes.

Calibration electrodes need to be patient, you will not be proficient at the beginning, and you will naturally become proficient after a long time.

It is very likely that what you said was not checked, for example, after I finished the x-axis, after the y-axis was removed, and after the completion of the work, I found that there would be a small shift in the x-axis. One or two more repetitions are required for the xy axis.

Low precision first find a piece of flat iron (preferably multi-faceted flat) about 40 centimeters, directly use the copper male reference table to discharge the iron block plane, debug until the spark is uniform, xy both directions need to be repeated once or twice, until the sparks on both sides are uniform, in the pull parallel. It is suitable for novice and experienced fast-acting copper (only for molds with low precision requirements).

High-precision die iron large plane and copper male are both effective table. The error is all within a wire. There is no shortcut to this, and you can only rely on your own familiarity to multi-effect a few times.

You have to foresee the meaning of the swing direction of the watch pointer, and then adjust the adjustment screw on the spark machine to a large extent, pay attention to its swing direction, and then you will understand, pay attention. It is a large adjustment to see clearly...

I've been learning spark machines for almost three months, and I don't work from time to time, and I always play exhaust and these things. If you go on like this, you will learn something. What a waste of time.