How to dismantle the split floor air conditioner indoor unit KFR 6l DyE3?

Dust fullness refers to the dust on the evaporator or filter screen of the indoor unit after being used for a long time.

The filter is in the lower part, and the panel in the lower half is opened by pulling it out of the upper part by hand, and it is good to take out the filter and wash it.

If you want to disassemble it yourself, you should first look at the assembly situation and then disassemble it, and you can remove the filter screen and wash it first, and the effect will be some.

There are several main types of Midea split wall-mounted air conditioners, the most common are wall-mounted air conditioners, as well as cabinet units, etc. The first is the wall-mounted air conditioner, which is an evaporation unit hung on the indoor wall. The position of the wall should not only consider the good indoor air convection effect, but also consider the distance as close to the outdoor unit as possible, and avoid over-long pipes to reduce the loss of cooling capacity.

The height of the indoor unit hanging is about 2 meters, and the ideal effect can be achieved.

In addition, it is also necessary to pay attention to the fact that the tuyere should not be directed at the person's body. The direction of the refrigerant pipes and drainage pipes should be well distributed to ensure that they are beautiful and useful. The cabinet air conditioner is installed on the floor heating, the air conditioner blows upward, and the air outlet grille can adjust the direction of the air outlet, which is generally used more in the living room with a relatively large area.

E3 means compressor low pressure protection. Causes and solutions: 1. Determine if the ambient temperature is too low. 2. To determine whether it is a control failure or a system failure, you can first short connect the LPP plug on the main control board and the neutral line N on the motherboard.

Dismantle the Midea split floor air conditioner, open the indoor unit F226LDY13, if you want to disassemble this, remove the screws from top to bottom, and then cut it open.

Dismantle the air conditioner first**Freon, and then remove the copper pipe, and the indoor unit can be removed.

Its disassembly is very simple to find its screws, and then twist its screws to disassemble, and it is a relatively simple way.

If you want to take it apart, in fact, the master of the air conditioner will come and turn it on directly.

Dismantle the beautiful split floor air conditioner indoor unit km2-6a.

How to remove Midea KFR-72LW DY-DC(E2) cabinet filter.

Hello, I'm glad to answer for you: 1. Before dismantling the canopy and unloading the air conditioning filter, first carefully open the air conditioning shell, generally the air conditioning shell is stuck with two small card slots, and gently open the outer cover outward. 2. After opening the outer cover of the air conditioner, there are often two buckles inside, and it is necessary to gently open the outer cover to fully open.

Then it is to take the filter, the filter is relatively easy to take, but it is stuck by a few card slots, first push the filter up, and then gently drag the filter down after the card slot. 3. After removing the filter screen, some air conditioners have black particles that strengthen the filtration, which should be taken off separately for cleaning and drying. Then carefully rinse the filter with clean water several times, you can scrub it with a soft brush several times, and finally dry it in a ventilated place until it is dry.

Be sure not to bend the filter when cleaning, although it is elastic, but Xinlu is plastic and cannot withstand bending.

Summary. Midea's mid-to-high-end cabinet machines; Method: Hold both sides of the lower panel of the air conditioner with your hands, pull it out forcefully and pull it apart, there is a filter screen on the separated lower panel, pull it out upwards Take the filter screen and rinse it under clean water, dry it and insert it, you can; Note:

When installing the panel, it should be noted that when the panel is buckled, the panel needs to be lifted upwards forcefully, otherwise the panel will not be buckled or there will be gaps.

Midea KFR-51LW DY-E2 dismantling and washing**.

Midea's mid-to-high-end cabinet machines; Method: Hold both sides of the lower panel of the air conditioner with your hands, pull it out forcefully and pull it apart, there is a filter screen on the separated lower panel, pull it out upwards Take the filter screen and rinse it under clean water, dry it and insert it, you can; Note: When installing the panel, it is necessary to pay attention to the need to lift the panel upwards when the panel is buckled, otherwise the panel cannot be buckled or there is a gap.

That's it. We hope you are informed.